Checked valve clearances today, have ?s
- ravenz07
-
Topic Author
- Offline
- User
-

Registered
- Posts: 108
- Thanks: 2
Checked valve clearances today, have ?s
03 Aug 2011 01:23
Checked the clearances on my 94 KZ1000P.
My results are:
Exhaust: (1-4)
.11, .13, .12, .09
Shims-
225, 2-0 (middle digit is missing), 230, 225
Intake:
<.04, <.04, <.04, .11
Shims-
2-0 (middle digit is missing), (no numbers at all), 240, 220
So my understanding is that number 4 on the exhaust will need to be replaced, and 1-3 on the intake will need to be replaced. Right? The smallest feeler gauge I have is a 0.04, and that would not go under the lobe. Which is a problem itself due to 3 were not legible. I will be picking up a micrometer tomorrow to find out the thickness.
What is the size of these shims width wise, 29mm?
Anyone have a smaller size shim I could try throwing in the few that were too tight to get a reading?
Comments?
My results are:
Exhaust: (1-4)
.11, .13, .12, .09
Shims-
225, 2-0 (middle digit is missing), 230, 225
Intake:
<.04, <.04, <.04, .11
Shims-
2-0 (middle digit is missing), (no numbers at all), 240, 220
So my understanding is that number 4 on the exhaust will need to be replaced, and 1-3 on the intake will need to be replaced. Right? The smallest feeler gauge I have is a 0.04, and that would not go under the lobe. Which is a problem itself due to 3 were not legible. I will be picking up a micrometer tomorrow to find out the thickness.
What is the size of these shims width wise, 29mm?
Anyone have a smaller size shim I could try throwing in the few that were too tight to get a reading?
Comments?
1994 Kawasaki KZ1000 Police
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim
Please Log in or Create an account to join the conversation.
- Jeff.Saunders
-
- Offline
- Vendor
-

Vendors
- Posts: 1238
- Thanks: 149
Re: Checked valve clearances today, have ?s
03 Aug 2011 08:12
If you can spin the shim/bucket youo have some clearance - it's just a little over zero - so you can assume you need to drop two shim sizes.
If you can't spin the bucket, the chances are you still will only need to drop two shim sizes - but that's something you need to check again after replacing the shim.
The 3 intake shims are the ones you must replace. The #4 exhaust you may want to change to get all 4 of the exhaust clearances as close to one another as possible.
If you can't spin the bucket, the chances are you still will only need to drop two shim sizes - but that's something you need to check again after replacing the shim.
The 3 intake shims are the ones you must replace. The #4 exhaust you may want to change to get all 4 of the exhaust clearances as close to one another as possible.
Please Log in or Create an account to join the conversation.
- KZ1000A2A
-
- Offline
- User
-

Registered
- Posts: 23
- Thanks: 1
Re: Checked valve clearances today, have ?s
03 Aug 2011 10:18
At the positions that the numbers are not readable put known thickness shims out of one of the other holes in those positions just to get an accurate measurement, will save you from buying shims not needed..
Please Log in or Create an account to join the conversation.
- ravenz07
-
Topic Author
- Offline
- User
-

Registered
- Posts: 108
- Thanks: 2
Re: Checked valve clearances today, have ?s
03 Aug 2011 14:52
Yes, unfortunately, you cannot turn the the motor with a shim missing. So I need to find a shim to test with.
1994 Kawasaki KZ1000 Police
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim
Please Log in or Create an account to join the conversation.
- ravenz07
-
Topic Author
- Offline
- User
-

Registered
- Posts: 108
- Thanks: 2
Re: Checked valve clearances today, have ?s
04 Aug 2011 22:21
1994 Kawasaki KZ1000 Police
Exhaust - 1 2 3 4
Clearance: 0.11mm 0.13mm 0.12mm 0.09mm
Shim Size: 225 - 230 225
Measured Shim: 2.25mm 2.29mm 2.30mm 2.24-2.25mm
Intake- 1 2 3 4
Clearance: <0.04mm <0.04mm <0.04mm 0.11mm
Shim Size: - - 240 220
Measured Shim: 2.30mm 2.35mm 2.40mm 2.20mm
(-)= Illegible/no number
Measured the shims today with a micrometer.
Exhaust - 1 2 3 4
Clearance: 0.11mm 0.13mm 0.12mm 0.09mm
Shim Size: 225 - 230 225
Measured Shim: 2.25mm 2.29mm 2.30mm 2.24-2.25mm
Intake- 1 2 3 4
Clearance: <0.04mm <0.04mm <0.04mm 0.11mm
Shim Size: - - 240 220
Measured Shim: 2.30mm 2.35mm 2.40mm 2.20mm
(-)= Illegible/no number
Measured the shims today with a micrometer.
1994 Kawasaki KZ1000 Police
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
