Compression Advice KZ900
- KZJOE900
-
Topic Author
- Offline
- Administrator
-

Super Users
- Posts: 1984
- Thanks: 455
Compression Advice KZ900
03 Aug 2011 14:28
Well, after reading through jcote75's compression thread, I decided on doing one myself before spending anymore money on cosmetics for this beast. The bike doesn't smoke. I got the following readings on a warm engine using a compression gauge on loan from Autozone:
#1: 110 psi
#2: 110 psi
#3: 90 psi
#4 95 psi
Did a wet test on #3 with probably two much oil and it went up to 155 psi. I know I should have continued the wet test on the rest of the cylinders but ran out of time.
According to the service manual I got from one of the threads here (Kawasaki Shop Manual Z-Series, from 1972 which seems outdated for a 76), the standard is 121 psi with a service limit of 85 psi and a maximum variation of 14 psi between cylinders. Is this correct for the 76 KZ900? So I know something is up with the rings, so I didn't even bother checking the valve clearance after finding out about the rings.
Just a brief history on the bike. I think it has been sitting since 2002. First in Alaska (probably outside) and then in Florida under a open sided carport at the PO's. The only thing I have done so far is strip and rebuild the carbs. Now it runs, albeit not perfect. I plan on adjusting and sync'ing the cabs when time permits. But it seems like it will be strong once it is tuned.
I saw somewhere on another thread a suggestion that the rings may be stuck, and that running it a few miles would loosen them up? I that possible in this case? How many miles should I try it for. How should I ride it, hard or go easy, vary the speed or steady cruising? I will do a tear down in the winter. But for now I would like to ride the thing a few months. Haven't had a bike since '93 and I'm itching to ride. Any suggestions are appreciated.
#1: 110 psi
#2: 110 psi
#3: 90 psi
#4 95 psi
Did a wet test on #3 with probably two much oil and it went up to 155 psi. I know I should have continued the wet test on the rest of the cylinders but ran out of time.
According to the service manual I got from one of the threads here (Kawasaki Shop Manual Z-Series, from 1972 which seems outdated for a 76), the standard is 121 psi with a service limit of 85 psi and a maximum variation of 14 psi between cylinders. Is this correct for the 76 KZ900? So I know something is up with the rings, so I didn't even bother checking the valve clearance after finding out about the rings.
Just a brief history on the bike. I think it has been sitting since 2002. First in Alaska (probably outside) and then in Florida under a open sided carport at the PO's. The only thing I have done so far is strip and rebuild the carbs. Now it runs, albeit not perfect. I plan on adjusting and sync'ing the cabs when time permits. But it seems like it will be strong once it is tuned.
I saw somewhere on another thread a suggestion that the rings may be stuck, and that running it a few miles would loosen them up? I that possible in this case? How many miles should I try it for. How should I ride it, hard or go easy, vary the speed or steady cruising? I will do a tear down in the winter. But for now I would like to ride the thing a few months. Haven't had a bike since '93 and I'm itching to ride. Any suggestions are appreciated.
Current project 76 KZ900 (This was a Vetter model)
76 KZ900
81 XJ550H SECA (Current Project)
82 XJ550R SECA
Past:
86 FJ1200
74 Z1900
72 CB450
76 KZ900
81 XJ550H SECA (Current Project)
82 XJ550R SECA
Past:
86 FJ1200
74 Z1900
72 CB450
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Compression Advice KZ900
03 Aug 2011 15:57That's surprising it could be that low. I thought it was more like 170 ballpark. The 750 twin is 155 psi.KZJOE900 wrote: Well, after reading through jcote75's compression thread, I decided on doing one myself before spending anymore money on cosmetics for this beast. The bike doesn't smoke. I got the following readings on a warm engine using a compression gauge on loan from Autozone:
#1: 110 psi
#2: 110 psi
#3: 90 psi
#4 95 psi
Did a wet test on #3 with probably two much oil and it went up to 155 psi. I know I should have continued the wet test on the rest of the cylinders but ran out of time.
According to the service manual I got from one of the threads here (Kawasaki Shop Manual Z-Series, from 1972 which seems outdated for a 76), the standard is 121 psi
At any rate: if it measured 100 psi and jumped to 155 with oil, that's really bad news for the rings (assuming data is correct).
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: Compression Advice KZ900
03 Aug 2011 17:32
Just ride the snot out of it and keep tinkering. Save your rebuild for the colder months.
I agree that those numbers are dismal, but hey - it goes right.
Advance your initial timing a few degrees.
I agree that those numbers are dismal, but hey - it goes right.
Advance your initial timing a few degrees.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- KZJOE900
-
Topic Author
- Offline
- Administrator
-

Super Users
- Posts: 1984
- Thanks: 455
Re: Compression Advice KZ900
03 Aug 2011 18:32 - 03 Aug 2011 18:36
I agree bountyhunter, the standard specs do seem low. All the threads I've read seem to suggest a higher value is normal. The service manual I got it from is date 1972. So I was hoping someone had specs which are more specific to the '76. TeK9iNe, I think I will do what you suggested no matter what I find out about the rings. Winter in Florida is actually the nicest time to ride, but I wouldn't want to do the tear down in the summer heat. I start to sweat even standing still this time of year. After searching again, I found another thread here by 2KZLTDs which answered my question about the possibility of stuck rings. There were suggestions about using the Yamaha 'Ring Free' and/or Seafoam. So I think I will try it out. Must have missed that thread. But unfortunately, as in a lot of these threads, there is no posting of the final resolution. So I don't know if these products had any effect on 2KZLTDs' compression. Still, I will get tags next week and see what kind of results I can get. Can anyone confirm if 121 psi is the standard compression for this bike? Joe.
Current project 76 KZ900 (This was a Vetter model)
76 KZ900
81 XJ550H SECA (Current Project)
82 XJ550R SECA
Past:
86 FJ1200
74 Z1900
72 CB450
76 KZ900
81 XJ550H SECA (Current Project)
82 XJ550R SECA
Past:
86 FJ1200
74 Z1900
72 CB450
Last edit: 03 Aug 2011 18:36 by KZJOE900. Reason: clarity
Please Log in or Create an account to join the conversation.
- cavanaughracing
-
- Offline
- User
-

Registered
- Posts: 213
- Thanks: 25
Re: Compression Advice KZ900
03 Aug 2011 19:02
Those are typical numbers for an old air cooled KZ that's in need of respiratory therapy
Larry C.
cavanaughracing.com
cavanaughracing.com
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
