issues around the starter clutch and rotor

  • Schorly
  • Schorly's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 82
  • Thanks: 1

issues around the starter clutch and rotor

04 Aug 2011 04:40 - 04 Aug 2011 05:18
#466752
I don’t know how often I had the rotor cover off to sort out the starter clutch on my 1982 CSR 1000 to either replace the three bolts holding the starter clutch to the rotor or re-tighten them or as it happened yesterday the rotor bolt was loose making the clutch assembly spinning on the crankshaft and not turning the engine over. I have used some none-permanent locking agent for the bolts but as I said the rotor bolt came loose. Any idea what I can do or have missed to make this part of the engine a bit more reliable?
1982 KZ1000 CSR M
Last edit: 04 Aug 2011 05:18 by Schorly.

Please Log in or Create an account to join the conversation.

  • Schorly
  • Schorly's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 82
  • Thanks: 1

Re: issues around the starter clutch and rotor

08 Aug 2011 10:58
#467684
I have purchased some higher strength locking agent and hope this will hold the centre bolt better. By the way, does anybody know how the oil drains back from the rotor housing? I always was wondering how the oil gets back from the there. I can only see an 8mm diameter howl on the top section behind the starter clutch, but the oil could not get up there for draining out?
1982 KZ1000 CSR M

Please Log in or Create an account to join the conversation.

  • steell
  • steell's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6849
  • Thanks: 208

Re: issues around the starter clutch and rotor

08 Aug 2011 11:20
#467689
You're putting the locking agent on the wrong part.

Assuming the crank is tapered and the bore in the flywheel has a matching taper, then it's the job of the taper fit to lock the rotor in place and keep it from spinning.
The problem is it sounds like the taper is messed up, either on the crank (really bad) or the rotor (merely bad). Assuming that's the case, I have used LocTite Stud and Bearing Lock to lock the rotor to the crank. Still working after three years.
KD9JUR

Please Log in or Create an account to join the conversation.

  • Schorly
  • Schorly's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 82
  • Thanks: 1

Re: issues around the starter clutch and rotor

08 Aug 2011 11:56
#467695
Yes, you are assuming right, the rotor sits on a tapered crank, but I don't think the taper is damaged. It is the bold which was loose when I opened the cover. i thought I had tightened it properly and applied locking agent, but both was not enough. So I hope the stronger locking agent will do the job.
1982 KZ1000 CSR M

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: issues around the starter clutch and rotor

08 Aug 2011 14:05
#467715
Some of the Kawasaki's had a woodruff key with matching slot cut in the crankshaft securing the rotor, others did not. See if there was once a keyway machined in the crank & rotor.

A woodruff key is a half moon solid piece of metal with one flat and one round side:
www1.mscdirect.com/cgi/NNSRIT2?PMAKA=679...ting-_-SearchResults (Just an example, not the size you may possibly need).
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • Schorly
  • Schorly's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 82
  • Thanks: 1

Re: issues around the starter clutch and rotor

08 Aug 2011 15:38
#467738
The tapered shaft on mine has no wood-ruff key. I understand a wood-ruff key to be a component more for indexing/ positioning rather than transferring loads. I am sure on my engine the problem is that the bolt came lose and even with a wood-ruff key I would have a problem.
1982 KZ1000 CSR M

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: issues around the starter clutch and rotor

08 Aug 2011 18:05
#467766
Did this condition appear out of the blue, say after a lengthy riding history with no such issue?

Or has it existed since acquiring the bike?

If a previous owner replaced the rotor with the wrong part from a similar model, the taper may appear the same, but be different enough to prevent fitment, in which event, a locking agent probably won't suffice.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: issues around the starter clutch and rotor

08 Aug 2011 18:43
#467784
One good fix is to get some machinist's lapping compound/valve grinding compound, and then by removing very small amounts of mismatch, by turning the rotor by hand with the compound on the crankshaft taper, it should make a tight fit(don't forget the locking compound on the bolt/nut).
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • Schorly
  • Schorly's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 82
  • Thanks: 1

Re: issues around the starter clutch and rotor

09 Aug 2011 11:24
#467988
I will have a look the next time the bolt is coming loose if I can improve the fit of the rotor, but in the meantime it all holds and the bike is starting well with the bolt tight.
In terms of the oil around the rotor, do you know how the oil drains back in to the crank case? I can not figure out how this works. If oil gets in it need to get out, otherwise I would have the whole rotor cover full of oil.
1982 KZ1000 CSR M

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: issues around the starter clutch and rotor

09 Aug 2011 12:59 - 09 Aug 2011 13:04
#468006
Schorly wrote: ...In terms of the oil around the rotor, do you know how the oil drains back in to the crank case? I can not figure out how this works. If oil gets in it need to get out, otherwise I would have the whole rotor cover full of oil.

There's supposed to be a little oil under the rotor cover.
FSM instructions say place a catch pan underneath when removing the cover.
In my experience, excess oil under the rotor cover hasn't been an issue.
The primary issue seems to be leakage past the rubber grommet where the wires exit the cover.

Here's the lubrication diagram as shown in the FSM for 1977~1979 KZ1000 (see below).

The magnified excerpt is colorized per my interpretation of the oil flow into and out of the area underneath the cover.
But I'm not positive about the exit route. :unsure:

I don't have an FSM covering the 1982 KZ1000, but would imagine that the lubrication diagram is very similar.

Good Fortune! :)

1973 Z1
KZ900 LTD
Last edit: 09 Aug 2011 13:04 by Patton.

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: issues around the starter clutch and rotor

09 Aug 2011 15:49
#468032
Schorly wrote: Yes, you are assuming right, the rotor sits on a tapered crank, but I don't think the taper is damaged. It is the bold which was loose when I opened the cover. i thought I had tightened it properly and applied locking agent, but both was not enough. So I hope the stronger locking agent will do the job.
You need to use acetone (carb cleaner spray) to get the bolt threads and the inside of the shaft threads DEAD CLEAN or the loctite won't hold. Also, let it cure fully.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum