I'm guessing clutch

  • Topper
  • Topper's Avatar Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
    Registered
  • Posts: 1609
  • Thanks: 133

I'm guessing clutch

04 Aug 2011 20:39 - 04 Aug 2011 20:43
#466877
!! Noob warning !!

Ok you've been warned.

I've been trying to get a '88 KZ305 back on the road. Was running and riding last fall, but it hasn't been happy since coming out of storage for the winter.

Current problem is that I'm not getting any power to the rear wheel at high (ish) rpms. It'll pull me around the yard and I don't have any real problems at 3k and lower.

But when the rpms get up above 3k it's like the rear wheel just isn't getting power anymore.

Seems pretty clear it's gotta be a clutch or transmission issue. I've tried adjusting the clutch cable and it's about at the end of its adjustable range.

Any suggestions on how to figure out exactly what's going on? I'm short on funds and don't want to throw money at the wrong parts.
Permanent and perpetual noob.

1979 KZ750 Twin
2009 Kawasaki Versys
Last edit: 04 Aug 2011 20:43 by Topper.

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: I'm guessing clutch

04 Aug 2011 21:00
#466880
Ask here about your 305 clutch problem: www.armbell.com/forum/index.php?c=17&sid...51fe6a6&mforum=kz400

Also what brand/type of oil used in the engine? "Car Oils" for the most part contain friction modifiers not compatable with motorcycle starter and wet plate clutches.

Oil is oil is not the same for a motorcycle.....
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: I'm guessing clutch

04 Aug 2011 21:25
#466884
Topper wrote: ...'88 KZ305...running and riding last fall...coming out of storage...not getting any power to the rear wheel at high (ish) rpms. It'll pull me around the yard and I don't have any real problems at 3k and lower.
But when the rpms get up above 3k it's like the rear wheel just isn't getting power anymore.
Seems pretty clear it's gotta be a clutch or transmission issue. I've tried adjusting the clutch cable and it's about at the end of its adjustable range....

Is clutch slipping, as evidenced by increased rpm absent increase in road speed?

Would also assure the timing advancer is functioning properly, and not stuck in the closed position.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • Topper
  • Topper's Avatar Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
    Registered
  • Posts: 1609
  • Thanks: 133

Re: I'm guessing clutch

04 Aug 2011 21:51
#466888
Patton wrote: Is clutch slipping, as evidenced by increased rpm absent increase in road speed?
Good Fortune! :)


Yeah that sounds like what I'm experiencing.

So I'm guessing I need to take the clutch apart and see what's what.

Will check the timing advancer first.
Permanent and perpetual noob.

1979 KZ750 Twin
2009 Kawasaki Versys

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: I'm guessing clutch

04 Aug 2011 22:13
#466892
Topper, doesn't the 305 have the clutch pushrod adjustment? A cover on your left side, where your sprockets at, about 2.5" long and 2 allen bolts attaching it.
Have the manual for your bike? Look up this adjustment.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • Topper
  • Topper's Avatar Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
    Registered
  • Posts: 1609
  • Thanks: 133

Re: I'm guessing clutch

04 Aug 2011 23:18
#466908
Motor Head wrote: Topper, doesn't the 305 have the clutch pushrod adjustment? A cover on your left side, where your sprockets at

I don't think the '88 has that pushrod adjustment, but I know what you're talking about. My '79 750 has it.

The manual I have covers too many years and models. It does mention the pushrod adjustment in the main section, but the supplements that cover my year don't mention it. And the cover shown in the photos isn't on my bike.

Is it possible there's a pushrod adjuster under the sprocket cover?
Permanent and perpetual noob.

1979 KZ750 Twin
2009 Kawasaki Versys

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: I'm guessing clutch

04 Aug 2011 23:20 - 04 Aug 2011 23:27
#466909
Does the cable still go in on the left side? Got a camera to post a picture?
It may not, as they did go away from it.

Looking at the parts Fiche for your bike, you don't have that adjustment. Sorry miss-leading you. :ohmy:

If the clutch is slipping then you would need at least new springs. Maybe clutch friction plates.
The 550 I had would slip under full power, untill I replaced the springs. Then it was fine. Cost $10 and 15min work. :)
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 04 Aug 2011 23:27 by Motor Head.

Please Log in or Create an account to join the conversation.

  • Topper
  • Topper's Avatar Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
    Registered
  • Posts: 1609
  • Thanks: 133

Re: I'm guessing clutch

04 Aug 2011 23:43
#466925
The cable routes over to the right side. I could take a pic tomorrow if needed.

15 minutes and $10 sounds like my kind of repair. The plates don't look too terribly expensive either.

How would I know if it's the springs or the friction plates? What am in for repair wise if it's the plates?
Permanent and perpetual noob.

1979 KZ750 Twin
2009 Kawasaki Versys

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: I'm guessing clutch

04 Aug 2011 23:48
#466928
Your manual should have the Min thickness spec for the plates. Both the Fiber and steels. The Fiber ones are most likely the only worn plates. I just put a set in my 1000 for $51 including shipping from Japan. After 3000mi they are working perfectly, and only needed 1 small adjustment.
They could be put in at the same time as new springs to give you a really fresh clutch.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • jonnybravo
  • jonnybravo's Avatar
  • Offline
  • Banned
  • Banned
    Registered
  • Posts: 518
  • Thanks: 18

Re: I'm guessing clutch

05 Aug 2011 00:06
#466935
Checked ur valves yet???

Please Log in or Create an account to join the conversation.

  • Topper
  • Topper's Avatar Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
    Registered
  • Posts: 1609
  • Thanks: 133

Re: I'm guessing clutch

05 Aug 2011 00:13
#466938
I found the procedure for replacing the friction plates in my manual. It doesn't look too hard even for a noob like me.

I guess I'll be tearing into the clutch this weekend.

Time to round up some parts.
Permanent and perpetual noob.

1979 KZ750 Twin
2009 Kawasaki Versys

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum