Problems installing cylinder head
- Brady Jenn
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
Problems installing cylinder head
05 Aug 2011 19:00
Hello everybody,
Im new to this forum and in need of help.
I have an '82 kz750H ltd with a stripped spark plug holes in the cylinder head. Ive bought a new head on ebay, which turns out is the black painted head from the specter model kz750. My mechanic installed the head and everything worked fine except the far left cylinder had zero compression. The reason is because the intake valve shim that came with the head is to big and won't allow the valve to close all the way. We established that we need a 200 size shim to make it work with the cam shaft from my old head. I cannot find this shim anywhere apparently its a very uncommon size.
Does anyone know where i can get a 200 shim or an intake camshaft from a specter engine?
Is it futile to try and use the specter head on my bike? If so does anyone have the head I need and would like to sell it?
Best,
Brady
Im new to this forum and in need of help.
I have an '82 kz750H ltd with a stripped spark plug holes in the cylinder head. Ive bought a new head on ebay, which turns out is the black painted head from the specter model kz750. My mechanic installed the head and everything worked fine except the far left cylinder had zero compression. The reason is because the intake valve shim that came with the head is to big and won't allow the valve to close all the way. We established that we need a 200 size shim to make it work with the cam shaft from my old head. I cannot find this shim anywhere apparently its a very uncommon size.
Does anyone know where i can get a 200 shim or an intake camshaft from a specter engine?
Is it futile to try and use the specter head on my bike? If so does anyone have the head I need and would like to sell it?
Best,
Brady
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Problems installing cylinder head
05 Aug 2011 19:11 - 05 Aug 2011 19:13
It's easy to grind the end of that valve a touch to allow using a thicker shim if you absolutely can't get the shim. The mechanic should have bench checked the valve clearances. I don't think changing cams will help, the cams that came with the head should work.
1979 KZ-750 Twin
Last edit: 05 Aug 2011 19:13 by bountyhunter.
Please Log in or Create an account to join the conversation.
- Brady Jenn
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
Re: Problems installing cylinder head
05 Aug 2011 21:05
So we tried sanding the shim itself and we got the valve clearance we needed but for some reason the left two cylinders are still getting a lower compression than the right two, around 60 psi vs. 90 psi. Do you know what compression we should be looking to get from this motor? It doesn't say in my manual. The head I bought seems to be in fine working order and I have new gaskets and everything. No leaks around the spark plugs. We are gonna do a liquid test to check for anything we can't see. Really appreciate the help, thanks a lot.
Brady
Brady
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Problems installing cylinder head
05 Aug 2011 21:17 - 05 Aug 2011 21:22
Per FSM:
Do not grind the shim. This may cause it to fracture, causing extensive engine damage.
FSM also provides specs and procedure to "tip" the valve (as bountyhunter suggested).
Your manual is like a new vacuum cleaner -- it really sux. :laugh:
Good Fortune!
Do not grind the shim. This may cause it to fracture, causing extensive engine damage.
FSM also provides specs and procedure to "tip" the valve (as bountyhunter suggested).
Your manual is like a new vacuum cleaner -- it really sux. :laugh:
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 05 Aug 2011 21:22 by Patton.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Problems installing cylinder head
05 Aug 2011 21:37
Here's a link to a website that includes a decent free down-loadable manual.
Click > kz.bike-night.com/
Good Fortune!
Click > kz.bike-night.com/
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Problems installing cylinder head
05 Aug 2011 22:12 - 06 Aug 2011 00:48
Back off your cams so they are not holding any valve open, or remove them. Then perform a Leak Down Test, as those compression #'s suck dude. That would be a waste of time and money without repairing the issue, find out whether its in the head or also rings. I would recommend doing the rings, and re-doing one of those two heads so you can be sure of decent #'s when you re-torque after a heat cycle.
Then I wonder why you are changing the head out for a couple of bad plug holes. There are Heli-coils, timeserts, and other Inserts that work quite well. this is a super common problem with Alloy heads. Ask anyone who owns a late model Ford truck, those blow plugs out all the time!
Any chance your compression gauge is off like 40psi?
Then I wonder why you are changing the head out for a couple of bad plug holes. There are Heli-coils, timeserts, and other Inserts that work quite well. this is a super common problem with Alloy heads. Ask anyone who owns a late model Ford truck, those blow plugs out all the time!
Any chance your compression gauge is off like 40psi?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 06 Aug 2011 00:48 by Motor Head.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Problems installing cylinder head
05 Aug 2011 22:19The shims are surface hardened (very thin layer) and grinding the hardening off weakens them. It will also cause them to wear really fast if the valve stem is banging on a shim face with no hardening.Patton wrote: Per FSM:
Do not grind the shim. This may cause it to fracture, causing extensive engine damage.
FSM also provides specs and procedure to "tip" the valve (as bountyhunter suggested).
Your manual is like a new vacuum cleaner -- it really sux. :laugh:
Good Fortune!
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Problems installing cylinder head
05 Aug 2011 22:23The only time mine ever read that low it had s erious problem with a valve not seating. IMHO, that head should have been gone through by a machinist to lap the valves and check things before installing.Brady Jenn wrote: So we tried sanding the shim itself and we got the valve clearance we needed but for some reason the left two cylinders are still getting a lower compression than the right two, around 60 psi vs. 90 psi.
Brady
On a 750 twin, stock compression is about 155 psi. I thought the fours were higher like the 160 - 180 ballpark, just my memory.Brady Jenn wrote: Do you know what compression we should be looking to get from this motor? It doesn't say in my manual.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: Problems installing cylinder head
05 Aug 2011 22:30Brady Jenn wrote: So we tried sanding the shim itself and we got the valve clearance we needed ......Brady
I would throw any shim you "sanded" away. The odds are you removed the hardened surface which means the shim will cause you more grief than it is worth. What manual are you using? Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- Brady Jenn
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
Re: Problems installing cylinder head
06 Aug 2011 01:44
Thanks for all the responses guys. I will get rid of the sanded shim asap. And taking the head to a machinist sounds like a good idea. Downloaded the manual thanks a lot.
I tried remedying the stripped spark plug threads in my original head with a sleeve about a month or two ago. It worked and the bike ran beautifully for about 500 miles until i pulled over at a gas station and noticed that my plug was blue and very lose. I rode to a mechanic shop and tried tightening the plug back down which immediately caused that cylinder to not fire at all. I then pulled the plug all the way out with the sleeve stuck to it only to find the end of the sleeve battered and mashed up like the valve had been hitting it inside the cylinder though i never heard any odd valve noise while riding it or had any loss of power. I tried a new shorter sleeve and new plug only to find that no matter what i did the plug screwed in at a hard angle, no where near strait. Somehow that seemed to not matter and the bike ran great again except i know could feel exhaust escaping through that plug hole. The quick fix didn't last though and i noticed the bike feeling a little sluggish and my plug was turning blue again, so thats when i made the decision to get this new head and gaskets. The guy I'm working on it with is knowledgeable about old japanese bikes so I would find it odd if he would miss diagnosing bad piston rings, but it was his idea to sand the shim...Maybe a did some real damage to the bike not getting it properly fixed right away. But I didn't have all this low compression bs until I put that new head on, but my mechanic says it the part looks in fine condition.
I tried remedying the stripped spark plug threads in my original head with a sleeve about a month or two ago. It worked and the bike ran beautifully for about 500 miles until i pulled over at a gas station and noticed that my plug was blue and very lose. I rode to a mechanic shop and tried tightening the plug back down which immediately caused that cylinder to not fire at all. I then pulled the plug all the way out with the sleeve stuck to it only to find the end of the sleeve battered and mashed up like the valve had been hitting it inside the cylinder though i never heard any odd valve noise while riding it or had any loss of power. I tried a new shorter sleeve and new plug only to find that no matter what i did the plug screwed in at a hard angle, no where near strait. Somehow that seemed to not matter and the bike ran great again except i know could feel exhaust escaping through that plug hole. The quick fix didn't last though and i noticed the bike feeling a little sluggish and my plug was turning blue again, so thats when i made the decision to get this new head and gaskets. The guy I'm working on it with is knowledgeable about old japanese bikes so I would find it odd if he would miss diagnosing bad piston rings, but it was his idea to sand the shim...Maybe a did some real damage to the bike not getting it properly fixed right away. But I didn't have all this low compression bs until I put that new head on, but my mechanic says it the part looks in fine condition.
Please Log in or Create an account to join the conversation.
- elfmagic17
-
- Offline
- User
-

Registered
- Posts: 334
- Thanks: 24
Re: Problems installing cylinder head
06 Aug 2011 02:07Brady Jenn wrote: So we tried sanding the shim itself and we got the valve clearance we needed but for some reason the left two cylinders are still getting a lower compression than the right two, around 60 psi vs. 90 psi.
Brady
Double check your Cam timing, if its off a tooth on one of the cams it will cause a low compression issue too. Done this myself once!!
Kenny Hicks
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Problems installing cylinder head
06 Aug 2011 09:33 - 06 Aug 2011 10:11
The cylinder that had the metal plug insert trouble, is it the one with low compression? What does the top of the piston look like, beat up and marked? The Piston Ring Land could be pinched, causing the upper compression ring to be stuck in the upper groove. Then the metal from it has probably scored the cylinder wall, and small pieces are on at least the upper ring. Better pull the jugs off and inspect.
Depending on the brand of the insert, there are a few with a different outer diameter and still the same size inside diameter. You can buy some pretty large outside diameter ones, Bluepoint/ Snapon has a kit for those later Fords with one that is really big. Stainless steel and still 3/4 reach.
But this other head maybe just needs a disassemble for inspection. Pretty easy to see pits in a valve face or seat, or if the seat width is to wide. Personally, I don't know if the Combustion Chamber Sizes changed any through the years on your motor. A way to check that would be to measure the liquid volume of the combustion chamber and compare to the original head. Its called "CC"ing.
This is another possibility for low compression #'s. Besides having a Bum gauge. That is where a leak down test is best. If you have under 25% leakage and when checking with 2 compression gauges shows the same low #'s, then I would suspect a low compression Ratio due to a large combustion chamber.
Depending on the brand of the insert, there are a few with a different outer diameter and still the same size inside diameter. You can buy some pretty large outside diameter ones, Bluepoint/ Snapon has a kit for those later Fords with one that is really big. Stainless steel and still 3/4 reach.
But this other head maybe just needs a disassemble for inspection. Pretty easy to see pits in a valve face or seat, or if the seat width is to wide. Personally, I don't know if the Combustion Chamber Sizes changed any through the years on your motor. A way to check that would be to measure the liquid volume of the combustion chamber and compare to the original head. Its called "CC"ing.
This is another possibility for low compression #'s. Besides having a Bum gauge. That is where a leak down test is best. If you have under 25% leakage and when checking with 2 compression gauges shows the same low #'s, then I would suspect a low compression Ratio due to a large combustion chamber.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 06 Aug 2011 10:11 by Motor Head.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
