1978 kz650 Engine case reassembly
- nitrochristian
-
Topic Author
- Offline
- User
-

Registered
- Posts: 39
- Thanks: 0
1978 kz650 Engine case reassembly
09 Aug 2011 01:04
Time to put the 1978 kz650 back together, but I think I lost a couple of dowel pins needed to join the engine cases? there are two one on each side right behind the crank journals they are still in place but there are two other holes that look like I need dowels one at front center and one at rear center. I looked on bikebandit and bought the dowels but the holes are different sizes, the top case holes are 10mm but the bottom case holes are smaller so the dowels wont work so are there suppose to be dowels here???? plz help
78 KZ650
96 Ford Bronco
96 Ford Bronco
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: 1978 kz650 Engine case reassembly
09 Aug 2011 10:23
Take a look at "CRANKCASE BOLT & STUD PATTERN" in the parts diagrams on Kawasaki.com. It shows where dowels are used. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 1978 kz650 Engine case reassembly
09 Aug 2011 10:42
Lots of good info on kawasaki.com, including parts diagrams, part numbers, models sharing same part, availability, etc.
Here's a link for help with navigating the site and finding information.
kzrider.com/index.php?option=com_kunena&...w&catid=13&id=376734
Good Fortune!
Here's a link for help with navigating the site and finding information.
kzrider.com/index.php?option=com_kunena&...w&catid=13&id=376734
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- OnkelB
-
- Offline
- User
-

Registered
- Posts: 1011
- Thanks: 80
Re: 1978 kz650 Engine case reassembly
09 Aug 2011 12:17 - 09 Aug 2011 16:24
There are only the two dowel pins you mention, one on each side right behind the crank.
However, in the upper case there are also two small locating pins that should fit into the shaft bearing races (clutch shaft and output shaft), one opposite the clutch and one opposite the output sprocket, make sure you get the races positioned correctly (pin in hole) before you tighten the cases, same goes for the half-moons.
However, in the upper case there are also two small locating pins that should fit into the shaft bearing races (clutch shaft and output shaft), one opposite the clutch and one opposite the output sprocket, make sure you get the races positioned correctly (pin in hole) before you tighten the cases, same goes for the half-moons.
77 KZ 650 B1, 82 GPz 1100 B2.
Last edit: 09 Aug 2011 16:24 by OnkelB.
Please Log in or Create an account to join the conversation.
- nitrochristian
-
Topic Author
- Offline
- User
-

Registered
- Posts: 39
- Thanks: 0
Re: 1978 kz650 Engine case reassembly
14 Aug 2011 01:20
Thanks for the info but one more time plz, do you know what these holes are for and do you know why bike bandit and other companys sell dowel pins for the holes when the wont work. we are really wanting to put the engine back together but we are fearful due to all the work and money we have spent if we screw up and leave a part out it will take another year to replace all the parts we bought. thks for the help
78 KZ650
96 Ford Bronco
96 Ford Bronco
Please Log in or Create an account to join the conversation.
- OnkelB
-
- Offline
- User
-

Registered
- Posts: 1011
- Thanks: 80
Re: 1978 kz650 Engine case reassembly
14 Aug 2011 07:17 - 14 Aug 2011 07:28
If you check the parts diagrams at Kawasaki.com they list two dowel pins (p/n: 92043-1037, size 10x8.2x14)) being used.
According to the diagram these two dowel pins should be installed in he holes you mention, front center and rear center - however there is no mention whatsoever of the two dowel pins behind the crank (which would bring the number of dowel pins up to four).
I'll stick my neck out and say that the diagram got it wrong (wouldn't be the first time I found an error in the diagrams/parts list there) - BikeBandit and others probably lift their info from the diagrams which would explain why they sell the pins for those holes.
I have personally split and reassembled two 650 engines, none of them had more than the two dowel pins behind the crank, neither does the spare set of cases I have in my garage.
Edit: I just asked the guys over at KZ650.info for verification on this, I'll let you know what they have to say.
According to the diagram these two dowel pins should be installed in he holes you mention, front center and rear center - however there is no mention whatsoever of the two dowel pins behind the crank (which would bring the number of dowel pins up to four).
I'll stick my neck out and say that the diagram got it wrong (wouldn't be the first time I found an error in the diagrams/parts list there) - BikeBandit and others probably lift their info from the diagrams which would explain why they sell the pins for those holes.
I have personally split and reassembled two 650 engines, none of them had more than the two dowel pins behind the crank, neither does the spare set of cases I have in my garage.
Edit: I just asked the guys over at KZ650.info for verification on this, I'll let you know what they have to say.
77 KZ 650 B1, 82 GPz 1100 B2.
Last edit: 14 Aug 2011 07:28 by OnkelB.
The following user(s) said Thank You: nitrochristian
Please Log in or Create an account to join the conversation.
- OnkelB
-
- Offline
- User
-

Registered
- Posts: 1011
- Thanks: 80
Re: 1978 kz650 Engine case reassembly
16 Aug 2011 16:56
So a couple of guys answered over at KZ650.info - both of them rebuilt their engines recently and both agree: two dowel pins right behind the crank journals, that's it.
77 KZ 650 B1, 82 GPz 1100 B2.
The following user(s) said Thank You: nitrochristian
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
