bike not starting
- newowner79kz750b1
-
Topic Author
- Offline
- User
-

Registered
- 79 kz750b4
- Posts: 114
- Thanks: 0
bike not starting
17 Aug 2011 18:02 - 17 Aug 2011 18:15
so i got a kz750b4 twin a little over a month ago. rode great but had to have the choke on. cleaned the carbs,floats,adjusted the floats, cleaned the jets all that good stuff. now the bike ran without the choke up but still wasent quit right. found out that i needed a new coil.so i got a emgo one from z1 enterprises and it fired right up but still something was a little off. put new spark plug caps on and new plugs also. rode it around. parked it for like a week. came back to the bike to work on it. it started but wouldnt stay running. cleaned the float bowls and jets out again thinking maybe something was clogged. put everything back together and it wont start. it doesnt seem like its getting any spark either and i dont no why! its a new coil,new wires,new plug, and new caps. im stumped.:dry:
Last edit: 17 Aug 2011 18:15 by newowner79kz750b1.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: bike not starting
17 Aug 2011 23:25 - 17 Aug 2011 23:35newowner79kz750b1 wrote: kz750b4 twin...wont start. it doesnt seem like its getting any spark either and i dont no why! its a new coil,new wires,new plug, and new caps. im stumped.:dry:
Ignition coil must be receiving adequate voltage while the ignition switch is turned ON.
If not already done, would check for sufficient voltage being received at ignition coil primary terminal with ignition switch ON.
There are several places where voltage might be lessened or lost between the battery and the coil, such as fuse connections, wiring connectors, switches, etc.
With adequate voltage to coil, the signal from the ignition (via wire attached to the other coil primary terminal) to unground the coil must be present.
Here's an illustration with points.
If the Kawasaki electronic ignition is fitted, a rotor and module are located under the points cover (instead of points and condensers) with wires to an IC Igniter (box located under the seat or side cover) and signal wire from the IC igniter to unground the coil primary.
It is the ungrounding of a charged coil that causes the coil to fire high intensity voltage through the spark plug wires.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 17 Aug 2011 23:35 by Patton.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: bike not starting
17 Aug 2011 23:33
If needed, there's a 79kz750b1 wiring diagram in the FILEBASE.
Good Fortune!
Attachment filebasekzr.jpg not found
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- newowner79kz750b1
-
Topic Author
- Offline
- User
-

Registered
- 79 kz750b4
- Posts: 114
- Thanks: 0
Re: bike not starting
18 Aug 2011 20:04
do u think a bad battery could be causing my problem? usually if i was to charge it it would still start but its deff not starting.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: bike not starting
18 Aug 2011 20:52 - 18 Aug 2011 20:57
You need to clean the tank thoroughly, install inline filters and then overhaul the carbs. As long as there is dirt in the tank, you will have a permanent hobby of trying to start your bike.
"cleaned the carbs,floats,adjusted the floats, cleaned the jets"
Couple of suggestions:
Did you set the float height using clear tube and fuel level? If not, it will never run worth crap.
JETS: install a 50 pilot jet, it will run and start a lot better than the 45.
From: "parked it for like a week. came back to the bike to work on it. it started but wouldnt stay running."
That definitely sounds like fuel/carbs. Electrical problems don't get worse by parking for a week, but crud in a fuel system settles and chokes things.
"cleaned the carbs,floats,adjusted the floats, cleaned the jets"
Couple of suggestions:
Did you set the float height using clear tube and fuel level? If not, it will never run worth crap.
JETS: install a 50 pilot jet, it will run and start a lot better than the 45.
From: "parked it for like a week. came back to the bike to work on it. it started but wouldnt stay running."
That definitely sounds like fuel/carbs. Electrical problems don't get worse by parking for a week, but crud in a fuel system settles and chokes things.
1979 KZ-750 Twin
Last edit: 18 Aug 2011 20:57 by bountyhunter.
Please Log in or Create an account to join the conversation.
- newowner79kz750b1
-
Topic Author
- Offline
- User
-

Registered
- 79 kz750b4
- Posts: 114
- Thanks: 0
Re: bike not starting
18 Aug 2011 21:09
i infact did use the clear tube method for the floats and both were withen spec. i took the bowls off and all the jets and cleaned them two times. took the bowls off again to check and were spotless. i cleaned them anyway and made sure i could see through each little hole in the jets.
whats weird though is when i installed my emgo coil it fired right but but still ran a little off do to still have to tune the carbs. now im not getting any spark at all. or atleast i didnt see one. im not sure how bright the spark is supposed to be though. it was pretty bright out.
whats weird though is when i installed my emgo coil it fired right but but still ran a little off do to still have to tune the carbs. now im not getting any spark at all. or atleast i didnt see one. im not sure how bright the spark is supposed to be though. it was pretty bright out.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
