Broken chain guide damper?
- gwolever
-
Topic Author
- Offline
- User
-

Registered
- Posts: 237
- Thanks: 8
Broken chain guide damper?
18 Aug 2011 15:33
Hey guys. I've been working on the engine this week and ran into another problem. (Not as bad as the broken bolts/extractors though I think...which ended up costing me $180 for three bolts with the EDM at the shop by the way).
I was removing the cam chain tensioner to polish along with my engine covers and noticed that there was a broken piece of plastic down by the bottom of rear chain guide.
I am pretty sure this is the chain guide damper that sits above the chain guide holder:
So I was able to use needle nose pliers to pull the 2 broken pieces out. Should I be concerned here about any other small pieces (plastic slivers?) or should I just order a new one and replace it?
And to replace it, do I need to remove the cylinder block?
Thanks.
I was removing the cam chain tensioner to polish along with my engine covers and noticed that there was a broken piece of plastic down by the bottom of rear chain guide.
I am pretty sure this is the chain guide damper that sits above the chain guide holder:
Attachment 014.JPG not found
Attachment 015.JPG not found
Attachment 016.JPG not found
Attachment 018.JPG not found
So I was able to use needle nose pliers to pull the 2 broken pieces out. Should I be concerned here about any other small pieces (plastic slivers?) or should I just order a new one and replace it?
And to replace it, do I need to remove the cylinder block?
Thanks.
1982 KZ1000 CSR
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Broken chain guide damper?
18 Aug 2011 15:44
The rear pivot/ guide that the tensioner pushes on can only be replaced by removing the cylinder block. The front one will come out the top.
here is the Exploded view. Why did it break? IMHO chain slap. check those springs, I'd get new ones. Also there is a measurement in the service manual for chain stretch. the one in my signature covers all this. You can get a Hi-Vo master link which you rivet in.
here is the Exploded view. Why did it break? IMHO chain slap. check those springs, I'd get new ones. Also there is a measurement in the service manual for chain stretch. the one in my signature covers all this. You can get a Hi-Vo master link which you rivet in.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- gwolever
-
Topic Author
- Offline
- User
-

Registered
- Posts: 237
- Thanks: 8
Re: Broken chain guide damper?
18 Aug 2011 16:19
Thanks Motor Head.
I think the plastic was just turning brittle. When I was checking the 2 broken pieces in my hand, just a little pressure on them and they were starting of crack and fall apart.
I will most likely get new springs when I order the damper though, just to be on the safe side.
I think the plastic was just turning brittle. When I was checking the 2 broken pieces in my hand, just a little pressure on them and they were starting of crack and fall apart.
I will most likely get new springs when I order the damper though, just to be on the safe side.
1982 KZ1000 CSR
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Broken chain guide damper?
18 Aug 2011 18:23
I don't know how many miles are on your bike, or the condition. But when in that far; Rings, Valves refaced seats cut and new stem seals, plus the cam chain and guides, tensioner springs.
Then with the carbs off, have you been through them very recently? You get the Idea, try to get it back in great shape, if you have the time and $.
Then with the carbs off, have you been through them very recently? You get the Idea, try to get it back in great shape, if you have the time and $.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
