some ideas please
- pimpstic
-
Topic Author
- Offline
- User
-

Registered
- Posts: 34
- Thanks: 0
some ideas please
18 Aug 2011 15:44
Its a '78 KZ1000 LTD- some ideas of what I should do to the engine. It has 29,000 miles on it. I dont think I wanna bore it out.
78 KZ1000 LTD
YOUR NOT RIDE'N UNLESS YOUR KZ RIDE'N
YOUR NOT RIDE'N UNLESS YOUR KZ RIDE'N
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: some ideas please
18 Aug 2011 16:06 - 18 Aug 2011 16:07
without getting into the engine.
you can't go wrong with some mild cams,
www.dynoman.net/engine/cams/webcams_kawa.html#kz900
that kerker is is going to help and depending on what carbs you have you could go up in size a little bit.
probably no bigger than 34mm carbs.
carbs are expensive tho.new ones will be around $700.00
www.dynoman.net/carb/mikuniRS2.html
leon
you can't go wrong with some mild cams,
www.dynoman.net/engine/cams/webcams_kawa.html#kz900
that kerker is is going to help and depending on what carbs you have you could go up in size a little bit.
probably no bigger than 34mm carbs.
carbs are expensive tho.new ones will be around $700.00
www.dynoman.net/carb/mikuniRS2.html
leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Last edit: 18 Aug 2011 16:07 by 531blackbanshee.
Please Log in or Create an account to join the conversation.
- testarossa
-
- Offline
- User
-

Registered
- Attack life, it's only trying to kill you.
- Posts: 3673
- Thanks: 83
Re: some ideas please
18 Aug 2011 16:29
Run a compression test first. If it comes back low, then do a leakdown test next to determine if its the rings not holding compression or the valves.
On the other hand, if you have good compression, then I would pull the valve cover and have a look around. Check valve clearances, check the timing chain stretch, and have a look at the rollers. If anything doesn't check out there, then replace as necessary. Once you are sure that you have a decent motor, then drop in cams and carbs will be your easy power adders. Beyond that you start looking into spending quite a bit more money. All depends on how wild you want to get. Make sure you have a service manual handy when you do get under that valve cover. It will help you avoid a lot of pitfalls.
Also, check out your ignition to make sure you aren't loosing power from a poor state of tune. Make sure the timing advancer is lubricated and moving properly. Perform the electrical tests on your coils to make sure they are in spec. Also check that you are getting full battery voltage to the coils as it's common for these old wiring harnesses to corrode and add resistance to the ignition circuit. New spark plugs are cheap insurance.
Basically get caught up on all the maintenance and then you'll have a good baseline to start with. Oh yeah, I almost forgot. Just adding that 4 into 1 exhaust means that you will need to properly jet your carbs. You will likely be running lean if they were properly tuned for the stock pipes.
On the other hand, if you have good compression, then I would pull the valve cover and have a look around. Check valve clearances, check the timing chain stretch, and have a look at the rollers. If anything doesn't check out there, then replace as necessary. Once you are sure that you have a decent motor, then drop in cams and carbs will be your easy power adders. Beyond that you start looking into spending quite a bit more money. All depends on how wild you want to get. Make sure you have a service manual handy when you do get under that valve cover. It will help you avoid a lot of pitfalls.
Also, check out your ignition to make sure you aren't loosing power from a poor state of tune. Make sure the timing advancer is lubricated and moving properly. Perform the electrical tests on your coils to make sure they are in spec. Also check that you are getting full battery voltage to the coils as it's common for these old wiring harnesses to corrode and add resistance to the ignition circuit. New spark plugs are cheap insurance.
Basically get caught up on all the maintenance and then you'll have a good baseline to start with. Oh yeah, I almost forgot. Just adding that 4 into 1 exhaust means that you will need to properly jet your carbs. You will likely be running lean if they were properly tuned for the stock pipes.
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
