Removing crankshaft cover
- gwolever
-
Topic Author
- Offline
- User
-

Registered
- Posts: 237
- Thanks: 8
Removing crankshaft cover
18 Aug 2011 16:13
So I am finishing up polishing my engine covers, got to the timing plate cover, and was wondering...do I have to take the timing plate/ignition advance ass./pickup coil ass. off as well, or can I just unscrew the entire crankshaft cover and pull it from the engine to polish?
Thanks.
Attachment 021.JPG not found
Thanks.
1982 KZ1000 CSR
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: Removing crankshaft cover
18 Aug 2011 17:19
remove the three screws holding the ign. plate on and then remove the advancer and then you can get the housng off.
hth,
leon
hth,
leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Removing crankshaft cover
18 Aug 2011 18:32
Don't forget there's an oil seal under the cover for the crank, as long as you've got it off, replace it if possible, and maybe the gasket for the cover too.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- gwolever
-
Topic Author
- Offline
- User
-

Registered
- Posts: 237
- Thanks: 8
Please Log in or Create an account to join the conversation.
- gwolever
-
Topic Author
- Offline
- User
-

Registered
- Posts: 237
- Thanks: 8
Re: Removing crankshaft cover
18 Aug 2011 23:48
Do I have to have the camshafts and chain in place to take the bolt off of the plate/advancer?
1982 KZ1000 CSR
Please Log in or Create an account to join the conversation.
- roy-b-boy-b
-
- Offline
- User
-

Registered
- Posts: 3245
- Thanks: 103
Re: Removing crankshaft cover
19 Aug 2011 00:08 - 19 Aug 2011 00:09
The advancer can only go on two ways. If you put it on wrong you will be 180 deg. out on your timing and have to turn it. No biggie. Mark it if you can.
1979 LTD Street Fighter.1977 KZ1000
Last edit: 19 Aug 2011 00:09 by roy-b-boy-b.
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: Removing crankshaft cover
19 Aug 2011 10:30gwolever wrote: Do I have to have the camshafts and chain in place to take the bolt off of the plate/advancer?
no you just need to be able to block the crank with some wood or hold the crank it may not take much effort.the little bolt is the one you want to remove.
leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
