Z1 Classic will not run

  • Marvin
  • Marvin's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 4
  • Thanks: 0

Z1 Classic will not run

20 Aug 2011 19:50
#470453
I have a 1980 Z1 Classic that will not run all the time . It will start once in a great time. I have checked the coils , wiring , throttle position switch , compression , valves , fuel pressure , injectors and relay . The air flow meter valve checks good but I still think it is the problem or the computer. The bike seems to be rich when it does run. It has good spark . Does anyone have any idea whaat to do next . The bike fires like it wants to run but will not stay running when I release the starter button . Has anyone ever installed the megasqruit system?

Thanks
Marvin

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Z1 Classic will not run

20 Aug 2011 19:58
#470455
check Fuel pressure with a gauge Tee'd in before the fuel rail, so you see the regulated pressure. Also since it will not show any codes like modern systems. you must test everything manualy.
I have the service manual that should cover that system in my signature. but always remember, got the basics, compression? Ignition? etc.
If you do a search, i have posted quite a bit on that early system. One of the fellows found a cheap replacement for the throttle switch, and the Double relay was also shared with car systems. It is not a Kawasaki specific system, just some of the stuff. The computer I would say only fits the bike, but that is a guess.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Z1 Classic will not run

20 Aug 2011 20:02
#470456
Fuel pressure should be 33 PSI at idle, when the throttle/air box flap valve opens, it sould be 35 PSI. Checked the main pump relay? Good voltage to the fuel pump?
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • roy-b-boy-b
  • roy-b-boy-b's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 3245
  • Thanks: 103

Re: Z1 Classic will not run

20 Aug 2011 22:17
#470492
Do not try and work on this system without a manual. Really. roy
1979 LTD Street Fighter.1977 KZ1000

Please Log in or Create an account to join the conversation.

  • Marvin
  • Marvin's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 4
  • Thanks: 0

Re: Z1 Classic will not run

21 Aug 2011 17:35
#470705
I have a clymer service manual on this bike .I followed all the checks in the book . I installed a fuel pressure gauge before the fuel rail and the pressure is with in spec. I checked the fuel relay also and changed it with 2 different relays no change .I have a blue spark on the spark plugs plus I checked the coils as shown in the service manual and they checked good.Also checked the pick up coils and ic igniter and they checked good. I checked all the wiring and connections . I ohm the wires out plus I disconneced all the plugs on the wiring harness and sent 12 volts threw each wire with a load . Than I moved the wires around checking voltage when doing this and all checked good on the wiring with the voltage check and ohm check.I checked the throttle position switch per spec and all checked good. Also checked switch threw the wiring harness to the computer and checked good.When the bike starts it runs good most of the times but it seems to have rich exhaust flumes . A few times it did start it would not speed up and spit and pop out of the air metering valve box. This just happened a few times. I did check all the past posting on this bike and followed them . One of the checks on the air meter box had just a little low ohm reading. Should I take the cover off this and check all the solding joints and connections . This bike has only 5400 miles and I have own this bike since 1983 . I would like to swap out the air meter box and computer to see if this is the problem . But they are hard to find plus they cost a lot if this is not the problem . I will check the manual you sent to see if there is anything different to check than I have already checked . I have checked everything in the book I have . Valves good , compression 155 lbs , fuel pressure in spec , blue spark and check power to fuel injectors with noid lights all good .

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Z1 Classic will not run

21 Aug 2011 18:14
#470710
www.redlinecycle.com does have some of the Z1 classic parts now and then too.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Z1 Classic will not run

21 Aug 2011 18:18
#470712
Use the manual in my signature and check both the Engine Temp Sensor and Air Temp Sensor, at the plugin for the computer. Have you had you injectors cleaned/ tested, or at least had them out for a spray pattern/ leak check?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Z1 Classic will not run

21 Aug 2011 18:57
#470720
Kawasaki Fuel Injection Sensor Specs

Here's from my 1982 GPz1100 B2 factory shop manual:

Air temperature sensor spec(probably the one on the air filter housing, or next to it).

Meter at ohms X 1K ohms ( I use ohms X 2K as it works on my meter)
Disconnect the wiring from the harness, one meter probe to one of the connector pins, the other on the last pin.

Should read 2.0K ohms to 3.0 K ohms at 68 F, if your meter won't read this, try the 20K ohm setting.

A footnote says this reading is true when sensor temperature is 20C (68F), 4.7 K ohms to 7.6 K ohms when 0 C (32 F) and 1.4 K ohms to 2.2 K ohms when 30 C (86 F).

Engine temperature sensor spec:
Again, meter to 2K ohm settings, one meter lead to the push on terminal (remove the wire as it may give a false reading) and the other to a chassis ground(any Black with Yellow stripe wire is part of the ground circuit).

The readings will be the same as the air temperature sensor.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • Marvin
  • Marvin's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 4
  • Thanks: 0

Re: Z1 Classic will not run

22 Aug 2011 19:22
#470988
I did have the fuel injector cleaned and inspected at Southbay Injectors .Resistor / Ohm passed,flow rate all good , report said injectors flow match to within + /- 1.0% up to OEM spec.


Thanks
Marvin

Please Log in or Create an account to join the conversation.

  • Marvin
  • Marvin's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 4
  • Thanks: 0

Re: Z1 Classic will not run

22 Aug 2011 19:28
#470989
I checked the temperature sensor , checked good . Checked the air temperature sensor checked good . The manual you sent on the 81 & 82 is different on some of the things than my 80 Z1 Classic. My air temperature sensor is in the flow meter and cannot be replaced .One check on the flow meter terminals#34 & #35 potentiometer checked 311 ohm my book call for 350 - 400 ohm if less or more it said to replace flow meter . The manual you sent has this test 250 -400 ohm . Do you think this is bad . I have done some checking and the air flow and computer are different on the GPZ1100 than the Z1 Classic.I going to do some of the checks on the computer that is in the manual you sent Tuesday when I get time . Do you think these test will be good on my bike since the computer & air flow is different?

Thanks for the help
Marvin

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Z1 Classic will not run

22 Aug 2011 19:35
#470992
Contact Larry Cavan at www.cavanaughracing.com/ he might know more about the early FI classic like you've got.

Another website is: www.750turbo.com/home.htm as they use a similar FI system.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • trianglelaguna
  • trianglelaguna's Avatar
  • Offline
  • User
  • User
    Registered
  • New and improved - extra strength
  • Posts: 8019
  • Thanks: 236

Re: Z1 Classic will not run

22 Aug 2011 19:51
#470994
my very tiny small caveman 2 cents...."bad brain...only way to check it...is with a brand new one..that may be bad also..and copycat down a goose chase"....


that was my summer of riding a 81 gpz 1100 with a faulty brain/main box , under the tail...that is what i was told when i got the bike and the above statement came from the mechanic who was rolling the bike out to sell me from a bone yard......he said they wee the #1 culprit...bike would be fine and then out of no where couple of days a week, in the middle of passing cars it would sputter,foul a plug,or go onto two cylinders...hot plugs and octane boost..back pack with a plug ratchet and wire brush/plugs....what a loser..guy said the "black box " was 400 from kawi ,this must have been 89-90......to cheap then so i just swapped plugs....not much has changed..lol...

i also had some cycle folks during that summer repeat the bad computer under the tail stories...

hot plugs and junk in the gas ..it would all a sudden shoot a nice 3 foot flame when it sputtered at night...:laugh: ..people would come up at the next light hooting and egging me to do it again..it was a mistake ...:unsure:

sounds like you tested everything...test the main computer/is there such a beast...nice bike,low miles...i love that model...some folks never have a problem ...but rumors persist that all those kawi injected bikes broke
1976 KZ900
2003 ZX12R
2007 FZ1000
2004 ninja 250R for wife

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum