Timing issue?

  • gwolever
  • gwolever's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 237
  • Thanks: 8

Timing issue?

23 Aug 2011 22:38
#471299
I was removing the timing plate/ign. advance assembly to be able to pull off that engine cover to polish. The crank actually turned just a little (I saw the nearest piston move up about an inch in the cylinder). I checked my cam chain as it is tied to a board on the ceiling in the garage, and it had moved some, so I pulled the chain taut and just moved the crank back that small amount to where it was before.

Before pulling everything apart, I marked where the chain and cam sprockets lined up:

Attachment 015_2011-08-23.JPG not found



Attachment 016_2011-08-23.JPG not found



So as long as I line them back up, I figure I shouldn't have a timing issue. Am I safe to assume this?
1982 KZ1000 CSR

Please Log in or Create an account to join the conversation.

  • rcarver
  • rcarver's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 62
  • Thanks: 0

Re: Timing issue?

24 Aug 2011 22:10
#471575
You're good.
1979 KZ650 SR (aka: Stella Blue)

Please Log in or Create an account to join the conversation.

  • gwolever
  • gwolever's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 237
  • Thanks: 8

Re: Timing issue?

24 Aug 2011 22:37
#471578
Cool. Thanks.
1982 KZ1000 CSR

Please Log in or Create an account to join the conversation.

  • T_Dub
  • T_Dub's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1441
  • Thanks: 26

Re: Timing issue?

24 Aug 2011 23:02
#471583
Did you take the cams out? If so, you are not safe to assume that, as when you take them out you'll likely not get the chain on the same tooth on the crank. Best is to time it just like the manual says.
1977 KZ650B1
-810cc
-Cavanaugh Racing Head
-Mikuni RS34's
-GPR Muffler

Please Log in or Create an account to join the conversation.

  • rcarver
  • rcarver's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 62
  • Thanks: 0

Re: Timing issue?

25 Aug 2011 00:00
#471596
True...important the relation of the chain to crank did not change. I assumed it was set to TDC before messing with the cams and returned there after the misalignment.
1979 KZ650 SR (aka: Stella Blue)

Please Log in or Create an account to join the conversation.

  • gwolever
  • gwolever's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 237
  • Thanks: 8

Re: Timing issue?

25 Aug 2011 22:27
#471788
Good to know. Thanks guys. I was looking at getting the Xenon Timing Light with Advance from Harbor Freight. Is that what I should use? It is going for $30 right now. Does that sound like a good price?
1982 KZ1000 CSR

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Timing issue?

25 Aug 2011 22:57
#471799
A timing light will be good for setting the ignition timing. But they are referring to is the Mechanical timing of the Crankshaft to the Camshafts.
Your Service manual will show this, and have details of how to set/ check it. I strongly recommend going through the procedure.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: Timing issue?

25 Aug 2011 23:05
#471802
the valve cover on j-series motors has a tensioner/guide built in to it,when you reinstall the valve cover it should go right back into the same location if you dont turn the motor over.
id remove the tensioner on back of motor and reinstall it after you put valve cover back on to make life easier.DO NOT TURN THE MOTOR OVER WITH THE TENSIONER ON BACK OF MOTOR REMOVED!!!!!!!!!!!! B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • rcarver
  • rcarver's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 62
  • Thanks: 0

Re: Timing issue?

26 Aug 2011 11:09 - 26 Aug 2011 11:10
#471924
I had bad luck with an "el-cheapo" brand timing light I purchased from Advanced Auto. It did not work on my Dyna copper core wires, and the directions stated that a suppression type wire must be used which I thought was B.S.

So I purchased this one from Z1: www.z1enterprises.com/TimingWork-Light-Self-Powered-2581.aspx

It is pricey but works great and is self powered via 2 D-cell batteries so you don't need to fuss with the battery. And I have heard this type gives you more accurate readings.
1979 KZ650 SR (aka: Stella Blue)
Last edit: 26 Aug 2011 11:10 by rcarver.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum