29 Smoothbore question
- Dice
-
Topic Author
- Offline
- User
-

Registered
- Posts: 20
- Thanks: 0
29 Smoothbore question
27 Aug 2011 14:43
:huh: Have a question on a newly aquired set of smootbore 29's. I was in the process of cleaning them and saw that I have the 2.0 slides in them. From what I have seen these were for the Suzuki GS bikes, will these work on a Z1? The jetting was setup with 125 mains and 127.5 pilots. Any suggestions on how jetting changes with these particular slides over the 1.5 slides?
1975 Z1B
Please Log in or Create an account to join the conversation.
- peter1958
-
- Offline
- User
-

Registered
- Posts: 1553
- Thanks: 198
Re: 29 Smoothbore question
27 Aug 2011 15:17
www.z1enterprises.com/reference/z1-carb-guide.aspx
You might want to read this about slides
www.kzzone.com/
cavanaughracing.com/kzdata.html
www.mtceng.com/index.php/us-dealers/44-f...-performance-orlando
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Re: 29 Smoothbore question
27 Aug 2011 18:06127.5 pilots ?????Dice wrote: :huh: Have a question on a newly aquired set of smootbore 29's. I was in the process of cleaning them and saw that I have the 2.0 slides in them. From what I have seen these were for the Suzuki GS bikes, will these work on a Z1? The jetting was setup with 125 mains and 127.5 pilots. Any suggestions on how jetting changes with these particular slides over the 1.5 slides?
lay off the weed Bubs :laugh: :laugh:
Please Log in or Create an account to join the conversation.
- Jeff.Saunders
-
- Offline
- Vendor
-

Vendors
- Posts: 1238
- Thanks: 149
Re: 29 Smoothbore question
27 Aug 2011 20:52
The 2.0 slides work OK on the large cc Z1/KZ engines (1100cc or 1200cc). Becasue the larger cutaway allows more air, you have to compensate and run bigger pilot jets - typicaly 22.5 or 25.0. The issue is low-end throttle response on smaller engines (900 OR 1000cc). Fuel doesn't flow fast enough to effectively atomize the fuel - so you end up with rougher running and sluggish response at low rpm.
Please Log in or Create an account to join the conversation.
- Chaotic Reason
-
- Offline
- User
-

Registered
- Posts: 384
- Thanks: 15
Re: 29 Smoothbore question
27 Aug 2011 23:00
@Jeff-- Is that why they put the accl pump on the '80 kz1000 ST?
Michael
1980 KZ1000 shaft drive
1980 KZ1000 shaft drive
Please Log in or Create an account to join the conversation.
- Dice
-
Topic Author
- Offline
- User
-

Registered
- Posts: 20
- Thanks: 0
Re: 29 Smoothbore question
28 Aug 2011 15:59
Whoops, should of been 27.5 pilot jet. :blush:
I am going to drop the pilot jets down to either a 20 or 22.5 and see how it behaves. I am running a 1015cc wisco 10.5 topend with 400 lift cams and dyna ignition. Hopefully I can get it sorted out one way or another as these are a nice set of carbs. Thanks for the replies.
I am going to drop the pilot jets down to either a 20 or 22.5 and see how it behaves. I am running a 1015cc wisco 10.5 topend with 400 lift cams and dyna ignition. Hopefully I can get it sorted out one way or another as these are a nice set of carbs. Thanks for the replies.
1975 Z1B
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
