Help with removing the cams???

  • ravenz07
  • ravenz07's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 108
  • Thanks: 2

Help with removing the cams???

09 Sep 2011 15:51
#475426
I am attempting to adjust my valve clearances and I was not aware my 80 KZ750 (4 cylinder) LTD uses "under bucket" shims. I am aware of how to adjust shims, but my experience has been with the other type.

How can I remove the cams and get it back to where it was as easily as possible? Can I put the motor at TDC and mark the chain in relation to the cams and put it back the exact way when done?

What do I have to do with the cam chain tensioner?

Thanks in advance
1994 Kawasaki KZ1000 Police
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: Help with removing the cams???

09 Sep 2011 16:09
#475435
in a word, Yes.
but the best thing u can do is get a manual so u can follow all of the detailed instructions. it will tell u how many chain links go between the cam sprockets markings.
they even have pictures. for guys like me. lol
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • ravenz07
  • ravenz07's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 108
  • Thanks: 2

Re: Help with removing the cams???

09 Sep 2011 16:11
#475440
I have one but the pictures are just useless. They are too dark to see anything. Plus I feel it is not put into words all too well.
1994 Kawasaki KZ1000 Police
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim

Please Log in or Create an account to join the conversation.

  • ravenz07
  • ravenz07's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 108
  • Thanks: 2

Re: Help with removing the cams???

09 Sep 2011 16:16
#475443
Basically from what I see from the manual is it says to "lock" the CCT by removing the bolt that sticks out to the right of the motor and putting a longer bolt in its place. Is that all that needs to be done?
1994 Kawasaki KZ1000 Police
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Help with removing the cams???

09 Sep 2011 16:55 - 09 Sep 2011 16:56
#475458
kz.bike-night.com/

Scroll down to and click on "The Bible".

Good Fortune! :)
1973 Z1
KZ900 LTD
Last edit: 09 Sep 2011 16:56 by Patton.

Please Log in or Create an account to join the conversation.

  • RonKZ650
  • RonKZ650's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 3719
  • Thanks: 252

Re: Help with removing the cams???

09 Sep 2011 17:07
#475461
Yes, you need to lock the tensioner as you already know. This is the 6mm bolt on the side of the tensioner body. To lock the tensioner, simply remove that short bolt and thread in a longer bolt that will tighten against the tensioner to hold it in place. After this is done remove your valve cover. If you're careful and no moron has used gasket sealer you can remove the cover without ruining the gasket and it can be reused indefinately. Now to be safe turn the motor over clockwise with a 17mm socket on the right end of the crank until your timing marks for 1-4 indicate TDC. Now look at the cams and see the arrow on the exhaust sprocket pointing straight forward aligned with the top surface of the head and your intake facing straight back lining up with the top of the head. If the arrows are not this way, turn the motor over 1 complete revolution until 1-4 are again at TDC. Now you have cams in correct position should an accident happen during disassembly. Now the way to remove the cams as to not disturb the timing. Of course first remove the center idler sprocket from between the cams and now work on one cam at a time. Remove all 4 cam caps from one cam, push down on the chain where your center idler was and at the same time lift the cam towards the center of the engine. Be sure and keep the chain tight going down in the engine and keep all slack between the cams. Once the cam is in the center of the engine you can do your shim swaps, then carefully reposition the cam in place. The important part is keep all slack between the cams and the chain always tight going down into the engine. Bolt up the caps and you're done with that cam. Repeat for the other cam. Do it right and timing has not been goofed up. This is direct from Kawasaki 4/77 service bulletin. Get it all bolted up, reinstall your short bolt in the tensioner and you're done. Tighten cam caps to 8ft/lb or less.
321,000 miles on KZ's that I can remember. Not going to see any more.
The following user(s) said Thank You: Patton

Please Log in or Create an account to join the conversation.

  • ravenz07
  • ravenz07's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 108
  • Thanks: 2

Re: Help with removing the cams???

09 Sep 2011 17:31
#475466
The bolt on the CTT is the bolt on the right correct?

I had already removed the valve cover. Is this going to be an issue?
1994 Kawasaki KZ1000 Police
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim

Please Log in or Create an account to join the conversation.

  • ravenz07
  • ravenz07's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 108
  • Thanks: 2

Re: Help with removing the cams???

09 Sep 2011 20:26 - 09 Sep 2011 20:29
#475496
Sooo, lifting one of the buckets out, one of the shims popped out and dropped into the motor through the chain valley.

Cant seem to get it out with a magnet, all it did was get the chain all over the place.

How screwed am I?
1994 Kawasaki KZ1000 Police
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim
Last edit: 09 Sep 2011 20:29 by ravenz07.

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Help with removing the cams???

09 Sep 2011 22:56 - 09 Sep 2011 22:57
#475528
Drop the oil pan and pray you can find it. BTW, it is customary to pack the chain galley with rag when working up top. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Last edit: 09 Sep 2011 22:57 by 650ed.

Please Log in or Create an account to join the conversation.

  • ravenz07
  • ravenz07's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 108
  • Thanks: 2

Re: Help with removing the cams???

10 Sep 2011 00:05
#475549
Well I figured that out quickly once it happened lol.

I am going to try one last thing and get a flexible magnet.

Any advice on maybe convincing the shim to go down? Maybe a bit of shaking and engine turning?
1994 Kawasaki KZ1000 Police
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Help with removing the cams???

10 Sep 2011 00:12
#475552
I wouldn't be rotating the crankshaft with that shim floating around down there, it could end up getting pinched in a bad place. Also, I don't know if you removed both cams or just one. If you only removed 1 cam the other cam is still holding a valve open, so if you rotate the crank with the cam chain inoperable the cam won't rotate and the piston may hit a valve. I would keep trying with a magnet and if no luck pull the pan. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • ravenz07
  • ravenz07's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 108
  • Thanks: 2

Re: Help with removing the cams???

10 Sep 2011 01:24
#475582
I removed both pretty much. I suppose I could try some more and give it a good shaking if nothing else.

How plausible is it that it will make its way down to the oil pan?
1994 Kawasaki KZ1000 Police
1980 Kawasaki KZ750 LTD
1981 Yamaha XJ650H Maxim

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum