Just Scored Some Web Cams!

  • Tyler
  • Tyler's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 845
  • Thanks: 92

Just Scored Some Web Cams!

13 Sep 2011 17:07 - 13 Sep 2011 17:08
#476436
I finnaly got some e-bay karma for once. I have my clutch apart on my 650 and was parusing ebay for parts when I came across an brand new set of 110 grind web cams for a 650/750. I though for all of about 10 microseconds before buying them for a whopping $75 bones...

I need some advice before I install them and I hope Larry C. is reading. :whistle:

I have just rebuilt this engine with 10.4:1 Weisco pistons. The head got a valve job and I put it toegether with APE springs. So I should be able to just bolt these cams in. I am running my stock carbs that were rebuilt and jetted, stock airbox also an electronic ingnition. I run a kereker exhaust and my mixture is spot on right now. What can I expect when I install these cams? Will I be lean, or will it not make much difference?

I have a couple heads laying around, would it really pay have a real port job done? Is my stock head going to limit any gains form the cams?

Any advice would help.
If I knew what I was doing all the time life wouldn't be any fun.

'80 KZ650 E 700cc, dyna ignition and coils, frame up restoration, daily driver
'81 KZ1300 A3 full restoration, custom big bore pistons, 1400cc 6 cylinder super bike
"77 KZ650 B1 - Barn Find, work in progeress
"74 Yamaha DT 400 Enduro
Last edit: 13 Sep 2011 17:08 by Tyler.

Please Log in or Create an account to join the conversation.

  • cavanaughracing
  • cavanaughracing's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 213
  • Thanks: 25

Re: Just Scored Some Web Cams!

13 Sep 2011 20:54 - 13 Sep 2011 20:55
#476472
At the risk of Officer Bill [aka KZCSI] editing yet another of my posts....Here's my opinion.

Take the valves out of one of your spare heads and set the new 110 grind Web cams in with the inside cam caps [2 on each cam] in place with the dowels. Make sure the cams spin without hitting the tappet bores. You need those cam caps to center the cams.

If they spin free [they should but you ALWAYS check] then you're good to go. I would go up 2 sizes on the main jet and ride it. Adjust from there.

Obviously to get the most out of the motor, porting is the way to go but you're going to get a nice boost from those cams, even with a stock head.

Stock carbs are limiting the output as well. They'll restrict a good port job too so you may want to run down some 26mm carbs and then consider the port work.
Last edit: 13 Sep 2011 20:55 by cavanaughracing.

Please Log in or Create an account to join the conversation.

  • Tyler
  • Tyler's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 845
  • Thanks: 92

Re: Just Scored Some Web Cams!

13 Sep 2011 23:54
#476530
Thanks,

I will make sure I have clearnce before I install. I will see how it runs before I get into carbs and head work.

How will these cams affect the bottom end?
If I knew what I was doing all the time life wouldn't be any fun.

'80 KZ650 E 700cc, dyna ignition and coils, frame up restoration, daily driver
'81 KZ1300 A3 full restoration, custom big bore pistons, 1400cc 6 cylinder super bike
"77 KZ650 B1 - Barn Find, work in progeress
"74 Yamaha DT 400 Enduro

Please Log in or Create an account to join the conversation.

  • Tyler
  • Tyler's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 845
  • Thanks: 92

Re: Got the wrong cams, looking to sell or trade...

19 Sep 2011 14:22
#477883
I got my cams in mail today and founf they were not the cams marked on the box. They are not WEB 110's they are infact WEB 206's for the 900/1000 kz's. Damn it! :pinch:

They are stamped 206 on one end and measure .500 lift on the intake. I contacted the seller and he was sorry about the mistake and offered to refund.

I would like to offer these for sale or trade here. I paid $75 for these and $15 for shipping. So I would sell for $90 shipped, BUT i would much rather trade for a set of cams for my 650. .390 or .395 lift.

These are brand new WEB 206 cams, let me know if anyone is interested. If not I will just return them.
If I knew what I was doing all the time life wouldn't be any fun.

'80 KZ650 E 700cc, dyna ignition and coils, frame up restoration, daily driver
'81 KZ1300 A3 full restoration, custom big bore pistons, 1400cc 6 cylinder super bike
"77 KZ650 B1 - Barn Find, work in progeress
"74 Yamaha DT 400 Enduro

Please Log in or Create an account to join the conversation.

  • Jack
  • Jack's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 691
  • Thanks: 7

Re: Got the wrong cams, looking to sell or trade...

19 Sep 2011 16:25
#477908
Thought those numbers looked familiar - BIG cams for BIG motors - got a set in my 1500cc. dragbike. Great cams,race only - check the Web Cams page for their description and spec. If you need a set of cams like these ,the price is rock bottom.
79 KZ 1075 MKll
79 KZ 1500 MKll dragbike
Gone but not forgotten:
3 X 73 Z1's
1 X 74 Z1A
1 X 75 Z1B

Please Log in or Create an account to join the conversation.

  • joe k
  • joe k's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 64
  • Thanks: 1

Re: Got the wrong cams, looking to sell or trade...

22 Sep 2011 09:54
#478547
Tyler wrote: I got my cams in mail today and founf they were not the cams marked on the box. They are not WEB 110's they are infact WEB 206's for the 900/1000 kz's. Damn it! :pinch:

They are stamped 206 on one end and measure .500 lift on the intake. I contacted the seller and he was sorry about the mistake and offered to refund.

I would like to offer these for sale or trade here. I paid $75 for these and $15 for shipping. So I would sell for $90 shipped, BUT i would much rather trade for a set of cams for my 650. .390 or .395 lift.

These are brand new WEB 206 cams, let me know if anyone is interested. If not I will just return them.

Unfortunatly i don't have the cams you require for a swap but am interested in purchasing these off you, can you find out your side on what it costs to ship to Melbourne Australia and pm me your details so as to make payment thanks---Joe

Please Log in or Create an account to join the conversation.

  • Tyler
  • Tyler's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 845
  • Thanks: 92

Re: Got the wrong cams, looking to sell or trade...

03 Oct 2011 23:21
#481266
Last Call, these cams are still unspoken for. Anyone?
If I knew what I was doing all the time life wouldn't be any fun.

'80 KZ650 E 700cc, dyna ignition and coils, frame up restoration, daily driver
'81 KZ1300 A3 full restoration, custom big bore pistons, 1400cc 6 cylinder super bike
"77 KZ650 B1 - Barn Find, work in progeress
"74 Yamaha DT 400 Enduro

Please Log in or Create an account to join the conversation.

  • joe k
  • joe k's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 64
  • Thanks: 1

Re: Got the wrong cams, looking to sell or trade...

04 Oct 2011 05:12
#481296
Hi Tyler you have a pm from me please check as i still want these cams but was on the other side of Oz as sister had a stroke whilst driving home and is in a bad way.
Please email me bank or ebay or what ever way you want payment made to [email protected] if pm not getting through----Thanks----Joe

Please Log in or Create an account to join the conversation.

  • Tyler
  • Tyler's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 845
  • Thanks: 92

Re: Got the wrong cams, looking to sell or trade...

04 Oct 2011 10:55
#481320
I didn't get your last responce, after some time I thought you had lost interest.

All is well now, PM sent. ;)
If I knew what I was doing all the time life wouldn't be any fun.

'80 KZ650 E 700cc, dyna ignition and coils, frame up restoration, daily driver
'81 KZ1300 A3 full restoration, custom big bore pistons, 1400cc 6 cylinder super bike
"77 KZ650 B1 - Barn Find, work in progeress
"74 Yamaha DT 400 Enduro

Please Log in or Create an account to join the conversation.

  • joe k
  • joe k's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 64
  • Thanks: 1

Re: Got the wrong cams, looking to sell or trade...

04 Oct 2011 21:42
#481387
Tyler you have another pm, i suggest that ebay would possibly the best medium to transfer the funds----Thanks----Joe

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum