splitting the crank

  • crackfox1
  • crackfox1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 27
  • Thanks: 0

splitting the crank

14 Sep 2011 06:35
#476604
Hello all, I'm splitting the crankcase on my z1000st in order to change the output gear for a sprocket driven one. I did a temporary job involving a welder and the splined link piece from out of the shaft drive mechanism. (allowing me to use the bike until I had the appropriate gearbox). What I'd like to know before I lift out the engine is,. Can I split the crank without removing the top-end ? ie, can the crank bearing cap be removed from underneath, enabling me to turn the engine upside down on the bench to split. I cant make out in the manual whether the cranks fixing holes are in the upper or lower casing. If I do have to remove the top-end then I'll do it before pulling out the engine to reduce weight. Any info on this issue would be most welcomed. Thank you. Simon.

Please Log in or Create an account to join the conversation.

  • Harvey1327
  • Harvey1327's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 138
  • Thanks: 9

Re: splitting the crank

14 Sep 2011 07:29 - 14 Sep 2011 07:33
#476605
Hi Crack,
You can split the cases without removing the top end. I had stripped my
output shaft and replaced it with a longer shaft. A stock Z1000 spline
is only pretruding out 8mm,for the thickness of a stock sprocket.
I replaced it with an output shaft with a spline pretruding about 14mm.
I could not find out what bike it came out of but other than longer in
the spline it was identical. I have since found out after that it could
have come from a Z1R. I needed this as I'm running a 5/8 offset sprocket.

Remember to follow the manual closely. Referring to lining up the oil
holes on the shaft to the ones on the gears.

You don't have to go near the crank. You also can leave the clutch basket on too.
Gently gently and all will be ok. :whistle:

Goodluck.
1 x 77 Z1000
1080,cams,ported
29 smoothbores,
Akron rims,Martin Swingarm
1 x 77 Z1000
1327 Wiseco,cams
ported,34.5 S/bores
GSXR swingarm
RF900 frontend.
1 x 2008 Nightrain
shotgun shock,corbin
seat,fat bars,some bling.
www.kzrider.com/media/kunena/attachments/8119/IMG_0461.JPG
Last edit: 14 Sep 2011 07:33 by Harvey1327.

Please Log in or Create an account to join the conversation.

  • crackfox1
  • crackfox1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 27
  • Thanks: 0

Re: splitting the crank

14 Sep 2011 09:15
#476626
Thank's for that info, I've just re-built the top end and hate doing thing's twice. It's time to find out how strong my weld's been on top of the nut holding my makeshift offset sprocket on. simon.

Please Log in or Create an account to join the conversation.

  • 531blackbanshee
  • 531blackbanshee's Avatar
  • Offline
  • Vendor
  • Vendor
    Vendors
  • Posts: 7442
  • Thanks: 796

Re: splitting the crank

14 Sep 2011 11:28 - 14 Sep 2011 11:29
#476654
harvey is right.

could you post some pictures of your modification to get the sprocket on the shaft drive output shaft?

leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!

billybiltit.blogspot.com/

www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work

kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Last edit: 14 Sep 2011 11:29 by 531blackbanshee.

Please Log in or Create an account to join the conversation.

  • crackfox1
  • crackfox1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 27
  • Thanks: 0

Re: splitting the crank

14 Sep 2011 12:00
#476660
Sorry but I'm having trouble posting any of my pictures to the site. I've tried dozens of times and think it's to do with my pc set-up. However computers aren't my thing. I will as soon as I get the computer sorted. thanks. simon.

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: splitting the crank

14 Sep 2011 13:16 - 14 Sep 2011 13:17
#476677
crackfox1 wrote: Sorry but I'm having trouble posting any of my pictures to the site. I've tried dozens of times and think it's to do with my pc set-up. However computers aren't my thing. I will as soon as I get the computer sorted. thanks. simon.

While attempting to post a pic while using the following procedure, is is possible to determine where hitting a snag?

Attachment picpostnewsite.jpg not found




Good Fortune! :)
1973 Z1
KZ900 LTD
Last edit: 14 Sep 2011 13:17 by Patton.

Please Log in or Create an account to join the conversation.

  • crackfox1
  • crackfox1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 27
  • Thanks: 0

Re: splitting the crank

14 Sep 2011 14:01
#476686
[attachment:1]C:\fakepath\z1000st.jpg[/attachment]
This is what happens every time, any idea what the fakepath means ?

Please Log in or Create an account to join the conversation.

  • Chaotic Reason
  • Chaotic Reason's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 384
  • Thanks: 15

Re: splitting the crank

14 Sep 2011 14:42
#476698
I move the pictures I want to post to my desktop. For some reason this works for me. I try to keep the file size around a Meg too.
Michael
1980 KZ1000 shaft drive

Please Log in or Create an account to join the conversation.

  • crackfox1
  • crackfox1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 27
  • Thanks: 0

Re: splitting the crank

14 Sep 2011 16:16
#476731
Just tried again and apparently my single pic mounted to 74MB which exceeded the limit. ???

Please Log in or Create an account to join the conversation.

  • crackfox1
  • crackfox1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 27
  • Thanks: 0

Re: splitting the crank

14 Sep 2011 16:35
#476738
[attachment:1]C:\fakepath\z1 003.jpg[/attachment]

Please Log in or Create an account to join the conversation.

  • 531blackbanshee
  • 531blackbanshee's Avatar
  • Offline
  • Vendor
  • Vendor
    Vendors
  • Posts: 7442
  • Thanks: 796

Re: splitting the crank

14 Sep 2011 17:00 - 14 Sep 2011 17:02
#476745
sounds like you may need to resize them.

i use
www.resize.it/advanced-online-photo-tools.html

make the image 817 height

make the image 1089 width

then hit okay and save it,
then use the resized saved pic to post.

hth,
leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!

billybiltit.blogspot.com/

www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work

kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Last edit: 14 Sep 2011 17:02 by 531blackbanshee.

Please Log in or Create an account to join the conversation.

  • Chaotic Reason
  • Chaotic Reason's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 384
  • Thanks: 15

Re: splitting the crank

14 Sep 2011 17:13
#476749
Leon's tool is nice because you can choose the dimensions. I would suggest lowering your resolution on your camera a bit. Sound like your shooting each pic at 10-12 megapixals. For stuff like this, you can drop it down to 2 and still give good quality photos.
Alternatively, you could try opening the picture in Microsoft paint, click on the image tab at the top, and then on RESIZE. Put it to about 30% on horizontal and vertical and see what the size of the file is then. Then you'll have to save it. But change the name a bit so you can still keep your original pic.
Michael
1980 KZ1000 shaft drive

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum