Oil Pressure Switch leak
- bloglos
-
Topic Author
- Offline
- User
-

Registered
- Posts: 229
- Thanks: 0
Oil Pressure Switch leak
16 Sep 2011 12:24
Oil pressure switch is leaking oil behind my points plate. Just noticed it this morning after I pulled up to work. Pulled off the cover and I think it's leaking form there. Can I just tighten it? or is it slightly more complicated then this? Anyone else have this issue?
78 KZ650 C2 - Runner
77 KZ650 B1 - Project
77 KZ650 B1 - Project
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Oil Pressure Switch leak
16 Sep 2011 13:15
Determine if it's the switch body or where it screws into, if it's the body, it might need replacement. Otherwse, remove the switch, clean the hole, and put a few turns of the Teflon plumbers tape and re-install the switch.
www.z1enterprises.com might be able to get you a new switch.
www.z1enterprises.com might be able to get you a new switch.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- bloglos
-
Topic Author
- Offline
- User
-

Registered
- Posts: 229
- Thanks: 0
Re: Oil Pressure Switch leak
16 Sep 2011 13:40MFolks wrote: Determine if it's the switch body or where it screws into, if it's the body, it might need replacement. Otherwse, remove the switch, clean the hole, and put a few turns of the Teflon plumbers tape and re-install the switch.
www.z1enterprises.com might be able to get you a new switch.
Roger that. Do I need to drain the oil to remove the switch and or the switch body? I'm guessing I'll have to remove the points plate as well, which will require me to set the timing once everything is back on.
78 KZ650 C2 - Runner
77 KZ650 B1 - Project
77 KZ650 B1 - Project
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Oil Pressure Switch leak
16 Sep 2011 14:10
I'd think if you can tilt the bike,you can remove it without draining the oil(unless it's due for a change).
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- clutch
-
- Offline
- User
-

Registered
- I wish I had a tad more patience to do it better!
- Posts: 1051
- Thanks: 13
Re: Oil Pressure Switch leak
16 Sep 2011 14:52 - 16 Sep 2011 14:54
Had the same issue on my kz 750 e not long after I acquired it. I had to remove the pickup coils to get at it, and also had to buy* a new socket to get it out...I think it was 24 or 26mm size. I didn't drain the oil, just had it on the side kick stand and no oil drained when I pulled it out. Once replaced, no more oil on my foot.
Southern Maryland, USA
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
Last edit: 16 Sep 2011 14:54 by clutch.
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: Oil Pressure Switch leak
16 Sep 2011 21:25
If you need to remove the points plate here's a tip: Put a few small pieces of masking tape on the points plate and on the engine case adjacent to the plate. Then very carefully draw some reference lines on the points plate tape and engine tape so the lines align with each other. Do this in 3 or 4 locations as space permits. When you remove the plate, be careful not to disturb the tape. When you re-install the plate just carefully line up all the reference lines and your points timing should be back where it was before you loosened anything. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
The following user(s) said Thank You: wireman
Please Log in or Create an account to join the conversation.
- bloglos
-
Topic Author
- Offline
- User
-

Registered
- Posts: 229
- Thanks: 0
Re: Oil Pressure Switch leak
16 Sep 2011 23:35650ed wrote: If you need to remove the points plate here's a tip: Put a few small pieces of masking tape on the points plate and on the engine case adjacent to the plate. Then very carefully draw some reference lines on the points plate tape and engine tape so the lines align with each other. Do this in 3 or 4 locations as space permits. When you remove the plate, be careful not to disturb the tape. When you re-install the plate just carefully line up all the reference lines and your points timing should be back where it was before you loosened anything. Ed
Thanks for the great advice guys! So if the body itself is leaking, is there generally no saving it? Just replacement?
78 KZ650 C2 - Runner
77 KZ650 B1 - Project
77 KZ650 B1 - Project
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Oil Pressure Switch leak
16 Sep 2011 23:41
Yes, just replace it, no sense in trying to glue/seal it if oil has contaminated the switch body.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
