high revs
- 78kz400
-
Topic Author
- Offline
- User
-

Registered
- Posts: 16
- Thanks: 0
high revs
20 Sep 2011 19:22
I'm having some issues with my engine revs going up once the motor is at operating temp. It never did it before, but i had other issues i had to deal with like a missing spring in the carb (kehin cv32) with i replaced both with stock ones,and also replaced the leaking push rod oil seal(i had to split the case to do that) I cleaned the carb as best as i could and when everything was put back together thats when the rev problem started. Its timed proper at low rpm and high rpm and runs good, but once it gets to operating temp it seems to hang up around the 3200rpm range and then slooowwly will come back down to idle(1000-1100rpm)The throtle cables are adjusted proper,so could this be a carb problem or could it be a problem with the timing advance(streached spings) Sorry for the long 1st post i'v made but its driving me NUTS.
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: high revs
20 Sep 2011 19:38
Possible air/vacuum leak at several places:
1.The rubber ducting or boots between the air flter box and carbs.
2.The carb holders between the carb and engine.
3.The rubber plugs on the sync ports.
To check for these, use a spray of WD-40,brake cleaner or with and UNLIT PROPANE TORCH.
Check the operation of the mechanical ignition advancer by twisting it with the engine off, it should return to it's original position. If stcking, clean it and lune with a light oil like 3-in-one or sewing machine oil.
Check valce clearances too, as they will affect the operation when the engine is hot.
1.The rubber ducting or boots between the air flter box and carbs.
2.The carb holders between the carb and engine.
3.The rubber plugs on the sync ports.
To check for these, use a spray of WD-40,brake cleaner or with and UNLIT PROPANE TORCH.
Check the operation of the mechanical ignition advancer by twisting it with the engine off, it should return to it's original position. If stcking, clean it and lune with a light oil like 3-in-one or sewing machine oil.
Check valce clearances too, as they will affect the operation when the engine is hot.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Re: high revs
20 Sep 2011 21:03 - 20 Sep 2011 21:04
the propane torch works better IMO
oh and welcome, u should really intro urself in the appropriate section, WITH BIKE PHOTOS
oh and welcome, u should really intro urself in the appropriate section, WITH BIKE PHOTOS
Last edit: 20 Sep 2011 21:04 by jonnybravo.
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: high revs
20 Sep 2011 21:36MFolks wrote: Possible air/vacuum leak at several places:
1.The rubber ducting or boots between the air flter box and carbs.
2.The carb holders between the carb and engine.
3.The rubber plugs on the sync ports.
To check for these, use a spray of WD-40,brake cleaner or with and UNLIT PROPANE TORCH.
Check the operation of the mechanical ignition advancer by twisting it with the engine off, it should return to it's original position. If stcking, clean it and lune with a light oil like 3-in-one or sewing machine oil.
Check valce clearances too, as they will affect the operation when the engine is hot.
A good way to check for leaks is to temporarily idle the engine down as low as it can go and still run then spray carb cleaner around the mating surfaces of the carb holders and cylinder head and the carb holders and carbs. A leak will kill the engine or at least make a noticable change in the idle. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
