Camshaft lockup on rebuild. Help!!!

  • Sweet Back
  • Sweet Back's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 160
  • Thanks: 0

Camshaft lockup on rebuild. Help!!!

21 Sep 2011 15:20
#478357
Try to make this short, with enough details. I broke a piston. Since then, I had the cylinder replaced, all 4 honed. New piston and rings. As 2 valves were bent on original head, using head from a previous motor. All parts are KZ1000p, interchangeable years, 93 and 96. With only crankcase, motor spins freely. With cylinders on, motor spins freely. Once I put on the head and torque down cam shafts motor will not turn. I've torn down and rebuilt 4 times. Camshafts are installed properly, TDC on 1-4 verified by T mark, and visual through spark plug hole. Notches in cam shaft are opposite each other, marks on camshafts are lined up. When I go to turn motor, it moves maybe half inch, chain jumps, so the crankshaft wants to turn. But I believe the camshafts are binding under the caps. Camshaft bushings are in place, valves are moving as they should. Seems when I put the camshaft caps on, they sit flush, no interference when I tighten them, but I feel they are keeping the camshafts from spinning. Yes I have exhaust and intake camshafts in proper order. I'm at a loss. Any suggestions are welcome and needed for my sanity. Thanks in advance.
1996 KZ1000P

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Camshaft lockup on rebuild. Help!!!

21 Sep 2011 15:27 - 21 Sep 2011 19:14
#478360
The cam bearing caps are machined to match the head, and also they are #'d to match up with the corresponding boss on the head. 1-4, arrow pointing forward.
Did you use the caps from the head you have installed and them installed correctly? Then don't over torque the bolts, they won't take the 12 foot pounds listed in some manuals. Try 90-100 inch pounds, or so.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 21 Sep 2011 19:14 by Motor Head.

Please Log in or Create an account to join the conversation.

  • Old Man Rock
  • Old Man Rock's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6071
  • Thanks: 225

Re: Camshaft lockup on rebuild. Help!!!

21 Sep 2011 15:41 - 21 Sep 2011 15:47
#478364
Is timing chain adjuster in-place pre-rotation?

Regarding replaced cylinder, did you check piston deck heights?
Reasoning, my KZ1015cc cylinders came in a kit pre-bored and honed with higher compression pistons. Upon measuring deck heights, found the cyclinder had been milled more then spec'd... Pistons were hitting the valves... :pinch:

I doubled up my cylinder base gaskets 40,000 +/- 3,000 all good...

Just a thought,

OMR
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter

Phoenix, Az
Last edit: 21 Sep 2011 15:47 by Old Man Rock.

Please Log in or Create an account to join the conversation.

  • Sweet Back
  • Sweet Back's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 160
  • Thanks: 0

Re: Camshaft lockup on rebuild. Help!!!

21 Sep 2011 15:50
#478366
Cam chain tensioner is not in place per manual. I did not check deck heights. It is definitely a camshaft issue. I'll make sure the head is paired with original caps and camshafts. I have tried the 2 different sets of cams, but still using original caps. Head is different so must go in that route.
1996 KZ1000P

Please Log in or Create an account to join the conversation.

  • Old Man Rock
  • Old Man Rock's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6071
  • Thanks: 225

Re: Camshaft lockup on rebuild. Help!!!

21 Sep 2011 16:04
#478367
"When I go to turn motor, it moves maybe half inch, chain jumps"...

Possibly cam chain is bound below sprocket, insure it isn't...

With a free spin cam chain, lift up to catch crank sprocket, hold in place until on cam sprockets...

Get everything lined up (TDC 1/4, cam sprocket arrows to decking, 1 up & 44 pins over, cam caps in place), then insert timing chain adjuster, then rotate otherwise chain slack can bind or jump as you mentioned...

Just went through this last weekend Kawi P-21, gut feeling is cam chain is bound up down below...
But hey, what do I know....

Hope you figure it out,

OMR
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter

Phoenix, Az

Please Log in or Create an account to join the conversation.

  • Sweet Back
  • Sweet Back's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 160
  • Thanks: 0

Re: Camshaft lockup on rebuild. Help!!!

21 Sep 2011 16:26
#478369
OMR thanks. Only thing I question is the chain tensioner. Manual states do not install. Would it be better to simply push on it? And are you saying install the cross pin?
1996 KZ1000P

Please Log in or Create an account to join the conversation.

  • Sweet Back
  • Sweet Back's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 160
  • Thanks: 0

Re: Camshaft lockup on rebuild. Help!!!

21 Sep 2011 16:26
#478370
OMR thanks. Only thing I question is the chain tensioner. Manual states do not install. Would it be better to simply push on it? And are you saying install the cross pin?
1996 KZ1000P

Please Log in or Create an account to join the conversation.

  • kz10006
  • kz10006's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 37
  • Thanks: 9

Re: Camshaft lockup on rebuild. Help!!!

21 Sep 2011 17:13 - 21 Sep 2011 17:16
#478378
Does your head have the speedo drive gear in the head or is it the electronic speedo sensor. The worm gear can get cought up when you tighten down the cam caps if you do have one.
Last edit: 21 Sep 2011 17:16 by kz10006.

Please Log in or Create an account to join the conversation.

  • 531blackbanshee
  • 531blackbanshee's Avatar
  • Offline
  • Vendor
  • Vendor
    Vendors
  • Posts: 7442
  • Thanks: 796

Re: Camshaft lockup on rebuild. Help!!!

21 Sep 2011 18:00
#478386
sure would be nice to have been able to put the cams in the head without valves or springs and insure that the cams turn freely.

you could take the cams out and hold the cam chain up to insure that it stays on the lower sprocket while you turn the engine over and inusre that the chain turns freely with the crank sprocket.



leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!

billybiltit.blogspot.com/

www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work

kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0

Please Log in or Create an account to join the conversation.

  • Sweet Back
  • Sweet Back's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 160
  • Thanks: 0

Re: Camshaft lockup on rebuild. Help!!!

21 Sep 2011 18:06
#478387
No Speedo at all. I did verify that the cam chain spins freely on the bottom gear. I've torn it apart and put it together 4 times.
1996 KZ1000P

Please Log in or Create an account to join the conversation.

  • 531blackbanshee
  • 531blackbanshee's Avatar
  • Offline
  • Vendor
  • Vendor
    Vendors
  • Posts: 7442
  • Thanks: 796

Re: Camshaft lockup on rebuild. Help!!!

21 Sep 2011 18:12 - 21 Sep 2011 18:14
#478390
damn!






i hate to say it,




but.







if it was mine i would pull the head and take the valves and springs out and re-install the cams and caps and tighen them down and see if they are still locking up.
at least then you could confirm or deny that the caps are causing it.if they spin free with no valves and springs then you most likely are having valve to piston contact.

leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!

billybiltit.blogspot.com/

www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work

kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Last edit: 21 Sep 2011 18:14 by 531blackbanshee.

Please Log in or Create an account to join the conversation.

  • 531blackbanshee
  • 531blackbanshee's Avatar
  • Offline
  • Vendor
  • Vendor
    Vendors
  • Posts: 7442
  • Thanks: 796

Re: Camshaft lockup on rebuild. Help!!!

21 Sep 2011 18:17 - 21 Sep 2011 18:18
#478391
is the head gasket overhanging the bores?

in other words maybe the hole for the cylinders is std and your new over bore is contacting the edges of the head gasket.

leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!

billybiltit.blogspot.com/

www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work

kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Last edit: 21 Sep 2011 18:18 by 531blackbanshee.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum