Low compression

  • JanTaliban
  • JanTaliban's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Z750 LTD Twin -83
  • Posts: 45
  • Thanks: 0

Low compression

26 Sep 2011 17:00
#479715
I have about 116 psi on both cylinders, I have a KZ750 Twin -83. I tried a little oil i both cylinders an it bumped up to about 130 psi on both. I rebuilt the top end this spring, new cylinderblock, new pistons and rings but nothing done about the head. For three weeks ago I changed both intake valves, they were bent and after that the problems with compression arised, it also smokes oil when I open the throttle a couples of times and then close it again, a couple of seconds after, it smokes om idle for about ten seconds, no smoke when I rev it to 5000 rpm an holds it there for a while. When I changed the intakes, I lapped all four valves but I'm not shure if they are sealing ok. I didn't change the stemseals, I didn't have any. I would like to belive that the compression issue coming from the valves not sealing, but I can't stop thinking if it is the rings. Any input would be appreciated.
KZ 750 Twin -83

Please Log in or Create an account to join the conversation.

  • indianajames
  • indianajames's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 93
  • Thanks: 1

Re: Low compression

26 Sep 2011 17:48
#479723
hey jan whats with the user name ? some kinda joke i dont get ? maybe you could enlighten me.

Please Log in or Create an account to join the conversation.

  • jonnybravo
  • jonnybravo's Avatar
  • Offline
  • Banned
  • Banned
    Registered
  • Posts: 518
  • Thanks: 18

Re: Low compression

26 Sep 2011 17:52
#479727
I thought ur were supposed to change the seals as well

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Low compression

26 Sep 2011 18:10
#479732
I read your earlier post where you bent the valves and cracked the guides. You also said you were going to use a different head.
So you put new valves in what a different head or the one with the cracked valve guides? Also when valves come into contact with the piston, and bend, they can very easily Crimp the top Compression ring into the land. Look close at the tops of those pistons. Probably worth a base gasket to find out.
Do you know how to do a Leak Down Test? Best with a tool/ gauge so you know what amount is leaking from where. But you can just add air pressure to the cylinder when it is at TDC firing position both valves closed.
That's another, is the cam timing correct? Why/ what caused the bent valves? Did the cam chain tensioner fail?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • JanTaliban
  • JanTaliban's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Z750 LTD Twin -83
  • Posts: 45
  • Thanks: 0

Re: Low compression

26 Sep 2011 18:11
#479733
@Indianajames: Just a nick I sometimes use, nothing more.
KZ 750 Twin -83

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Low compression

26 Sep 2011 18:13 - 26 Sep 2011 18:15
#479734
The valve seals on these twins fail terribly. Replace them EVERY time the valves are out. Use VITON seals if you can find them.
new cylinderblock, new pistons and rings but nothing done about the head. For three weeks ago I changed both intake valves, they were bent and after that the problems with compression arised, it also smokes oil when I open the throttle a couples of times and then close it again, a couple of seconds after, it smokes om idle for about ten seconds,

Are you saying you bored the cylinders and installed new pistons and rings?

Sounds like bad seals for sure.
1979 KZ-750 Twin
Last edit: 26 Sep 2011 18:15 by bountyhunter.

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Low compression

26 Sep 2011 18:16
#479736
Motor Head wrote: I read your earlier post where you bent the valves and cracked the guides.
To anybody who cares, I have a full set of brand new OEM kawasaki valve guides for 750 twin and will sell at discount.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • JanTaliban
  • JanTaliban's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Z750 LTD Twin -83
  • Posts: 45
  • Thanks: 0

Re: Low compression

26 Sep 2011 18:28
#479738
Thanks Motor Head and Bountyhunter for your input. I changed the intakes on the head with the cracked guides, the valves were bent when I turned the engine over with a wrench, the camchain was a couple of teeth off and I didn't notice until I turned the engine over, I didn't start it until correcting it . I looked at the pistontops but I couldn't see any marks on them. I have ordered vitonseals for the other head, found them on eBay.
KZ 750 Twin -83

Please Log in or Create an account to join the conversation.

  • JanTaliban
  • JanTaliban's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Z750 LTD Twin -83
  • Posts: 45
  • Thanks: 0

Re: Low compression

26 Sep 2011 18:32
#479739
Actally, I didn't bore the cylinders, I put on a new cylinderblock and new pistons and rings.
KZ 750 Twin -83

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Low compression

26 Sep 2011 18:35
#479741
So the guides are still cracked? I wouldn't run it like that. Get the guides replaced and the Valve seats cut, new stem seals.
If you bent the valves by turning it by hand, then the piston would not of taken much force and the upper ring and land should be ok.
To test if your valves are seating a simple test is to fill the port up with a solvent and let stand. Any leak of fluid and it is not seating.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • JanTaliban
  • JanTaliban's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Z750 LTD Twin -83
  • Posts: 45
  • Thanks: 0

Re: Low compression

26 Sep 2011 18:42
#479742
I will replace the present head with the one I ordered, hopefylly it's ok, I will change the valve seals to VITON seals before I put it on. I also belive my starter is a bit weak, maybe it crank the engine enough to get a good reading? I don't know if using the kickstarter would work when testing compression.
KZ 750 Twin -83

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Low compression

26 Sep 2011 18:45
#479744
Did you warm the engine, then hold the throttle open, and kick it with the other plug out, until MAX gauge reading pumps up?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum