EXHAUST BOLT BROKE OUT
- crappiehuntr
-
Topic Author
- Offline
- User
-

Registered
- Posts: 43
- Thanks: 0
EXHAUST BOLT BROKE OUT
02 Oct 2011 04:26
I was removing exhaust to replace gaskets and right side bolt pulled out and broke were it mounted to head looks like it had been jb welded or something prior and the nut on the stud was seized causing it to brake is welding the only fix it was not leaking on that cylinder before and if the nut had not been seized I think it would have been ok but what did they use anything out there that works?
1977 KZ1000
1978 KZ650
1976 KZ900 project
1981 KZ550 project
1978 KZ650
1976 KZ900 project
1981 KZ550 project
Please Log in or Create an account to join the conversation.
- trianglelaguna
-
- Offline
- User
-

Registered
- New and improved - extra strength
- Posts: 8019
- Thanks: 236
Re: EXHAUST BOLT BROKE OUT
02 Oct 2011 07:51
in short....no...as you just found out.....
by the time i was done i had 50-75 in special taps and back outs and oversize sae thread efforts...along with all the high heat epoxies and metal fillers that i wasted money on...my stud was an inner cyl so i had to pull my engine and call around for a local welder that could weld on a aluminum ex area and would do a little job,he boogered it up nice with fresh molten alum and then used my taps... :laugh: i left him and my new from the deal 5 dollar studs and new nuts....one day deal 125.00 and done....never even think about again...imo dont waste time and $$$ just call around and see who can take a look at it for you...money well spent...there are other threads in the history here same deal...that is where i was told to weld only
goood luck...bummer...but easy fix if done right
by the time i was done i had 50-75 in special taps and back outs and oversize sae thread efforts...along with all the high heat epoxies and metal fillers that i wasted money on...my stud was an inner cyl so i had to pull my engine and call around for a local welder that could weld on a aluminum ex area and would do a little job,he boogered it up nice with fresh molten alum and then used my taps... :laugh: i left him and my new from the deal 5 dollar studs and new nuts....one day deal 125.00 and done....never even think about again...imo dont waste time and $$$ just call around and see who can take a look at it for you...money well spent...there are other threads in the history here same deal...that is where i was told to weld only
goood luck...bummer...but easy fix if done right
1976 KZ900
2003 ZX12R
2007 FZ1000
2004 ninja 250R for wife
2003 ZX12R
2007 FZ1000
2004 ninja 250R for wife
The following user(s) said Thank You: wireman
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: EXHAUST BOLT BROKE OUT
02 Oct 2011 12:00 - 02 Oct 2011 12:14
If you can weld, maybe your local supplier has some of this rod?
www.zena.net/htdocs/welders/Rods/Aluminum.shtml
It is pretty easy to use, and will fill that broken area. Then drill and re-tap, also cleaning up with a Dremel tool.
Some will die from laughter, but since the rod is DC, you may be able to "Macgyver" a weld using jumper cables and a Battery. Although you can't limit current flow easily, I wonder if using your Good bike battery would work? :blink:
As with any welding, testing on spare material to see if the temp and technique is correct, is recommended.
Post a Picture?
www.zena.net/htdocs/welders/Rods/Aluminum.shtml
It is pretty easy to use, and will fill that broken area. Then drill and re-tap, also cleaning up with a Dremel tool.
Some will die from laughter, but since the rod is DC, you may be able to "Macgyver" a weld using jumper cables and a Battery. Although you can't limit current flow easily, I wonder if using your Good bike battery would work? :blink:
As with any welding, testing on spare material to see if the temp and technique is correct, is recommended.
Post a Picture?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 02 Oct 2011 12:14 by Motor Head.
Please Log in or Create an account to join the conversation.
- Gary - K7GLD
-
- Offline
- User
-

Registered
- 1983 1100LTD
- Posts: 135
- Thanks: 17
Re: EXHAUST BOLT BROKE OUT
02 Oct 2011 17:18 - 02 Oct 2011 17:21
I've had good luck in the past using a reverse rotation drill bit slightly smaller in diameter than the bolt size - just need to be very careful to line the drill angle properly, and carefully center the drill bit - it helps to use a smaller bit size first to use as a pilot hole for the reverse bit - usually the heat and friction created by the reverse drill bit will quickly back out the broken stud...
John Day area - Eastern Oregon
Restored 1983 Kawasaki 1100LTD
Restored 1983 Kawasaki 1100LTD
Last edit: 02 Oct 2011 17:21 by Gary - K7GLD.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
