Take a look at this tach cable

  • Kapahulu
  • Kapahulu's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 564
  • Thanks: 41

Take a look at this tach cable

07 Oct 2011 23:28 - 07 Oct 2011 23:29
#481947
I'm picking up this KZ900 on another island, my friend went and looked at it today. Checkout this picture of the tach cable going into the head. I am guessing it needs a new oil seal and somebody did a hillbilly job of stopping the oil leak with gasket sealant.

Anyone want to voice concerns? I kind of wonder if the threading on the head is gone, seems unlikely though.
1978 KZ1000, 1976 KZ900, 1975 H2, 1973 H1, 1973 H2, 1978 RD400, 1977 RD400, 1974 RD350
2strokeworld.com
Last edit: 07 Oct 2011 23:29 by Kapahulu.

Please Log in or Create an account to join the conversation.

  • TeK9iNe
  • TeK9iNe's Avatar
  • Offline
  • User
  • User
    Registered
  • What did you do!?!
  • Posts: 2436
  • Thanks: 28

Re: Take a look at this tach cable

08 Oct 2011 00:15
#481954
Oh the horror, that is deffinately a hilbilly fix!

Fine threads or not, a new seal and a good fitting worm gear unit with some loctite, you'll be all set.

B)
Motorcycle Shop Owner/Operator

79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors ;)

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Take a look at this tach cable

08 Oct 2011 00:29
#481957
Kinda makes you wonder what other "improvements" the PO made to that poor bike. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • Kapahulu
  • Kapahulu's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 564
  • Thanks: 41

Re: Take a look at this tach cable

08 Oct 2011 01:10
#481970
Thanks for the feedback! The price is good, the bike has some rust and corrosion all over. That's what happens to motorcycles in Hawaii if they are left outside in the salt air.

I think it has a lot of potential. Here's another picture.
1978 KZ1000, 1976 KZ900, 1975 H2, 1973 H1, 1973 H2, 1978 RD400, 1977 RD400, 1974 RD350
2strokeworld.com

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: Take a look at this tach cable

08 Oct 2011 09:10
#481991
i find the same problem with mine. that seal tends to leak, even with a new seal. i had to use some silicone rtv sealer.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Take a look at this tach cable

08 Oct 2011 10:23 - 08 Oct 2011 10:25
#482005
mark1122 wrote: i find the same problem with mine. that seal tends to leak, even with a new seal. i had to use some silicone rtv sealer.

With as-new parts properly assembled and installed, it shouldn't leak, even without a tach cable attached.

The worm-gear drive-shaft must be in serviceable condition and not worn where it spins inside the oil seal.
The oil seal must be functional and properly installed inside the housing, which presupposes that the old rock-hard seal was first completely removed (helps to have lighted magnification and a dental pick). The old seal may resemble a chunk of carbon.

Sometimes, where residue from previous leakage has accumulated inside the tach cable, it will eventually ooze down and escape from the fitting where the tach cable attaches to the tach drive housing.

Where there's seepage (for whatever reason) from where the tach cable attaches to the tach drive housing, assuring a leak-free connection may contain the seepage and allow it to accumulate or remain captured inside the tach cable.

The tach drive housing (gear guide) with o'ring must fit snugly to prevent oil seepage around the housing.
Such leakage doesn't pass through the fitting where the tach cable attaches to the housing.
And a leak-free connection between tach cable and tach drive housing won't prevent seepage around the housing due to a defective o'ring (for example), regardless of having a leak-free connection where the tach cable attaches to the tach drive housing.

Good Fortune! :)
1973 Z1
KZ900 LTD
Last edit: 08 Oct 2011 10:25 by Patton.

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Take a look at this tach cable

08 Oct 2011 11:29
#482012
When mine leaked 4 years ago I replaced the whole set of related parts with NOS Kawasaki parts. Probably overkill, but it has not leaked since. Here's a pic of the parts involved:

Attachment tachseal.jpg not found

1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum