transmission troubles?

  • lewisj
  • lewisj's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 141
  • Thanks: 4

transmission troubles?

09 Oct 2011 18:00
#482185
Here's the background, 73 Z1, 1075cc, .418 cams, 29 smoothbores, backcut transmission,appox.1500 miles since rebuild.

Here's the problem: Took a nice ride on Friday and found that when I downshifted, the shift lever stayed down, and would not return to the "up" position unless done so manually with my foot. When shifted down, it felt mushy and soft and the lever simply stayed down. The further I rode the more gremlins entered into the picture, it became very hard to shift to the next gear and often would not engageuntil downshifting and staring the sequence again. all the symptoms were sporadic. I went back out yesterday and the same symptoms appear on both down shifts and upshifts.

Any idea's fella's. Shifting fork or a clutch problem?

Thanks ahead for your help!!

Jim
1973 Z1
1075cc MTC kit
Andrews 3X cams
ZRX 1200 swingarm

Vance&Hines header/ exhaust
29mm smoothbores w/pods
ZR7S 41mm Front Forks with 17" wheels

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: transmission troubles?

09 Oct 2011 18:23
#482192
You're going to need to remove the engine sprocket cover,shifter lever & possible the left side footpeg to get to the problem parts.

See if www.z1enterprises.com can get you the return spring,gasket & both seals.

I'd remove the engine sprocket & possibly the chain as the return spring has probably broken on the shift lever. To access it, remove the 'mission cover(transmission cover)and have a new gasket and seals ready. The cover has both the shifter shaft and engine output shaft going through it.

Tilt the bike to the right if possible to reduce any oil spillage. When getting ready to re install the transmission cover, and after the seals have been replaced, put several layers of tape on the output shaft splines & with a thin coating of grease to prevent tearing of the output shaft seal.

The shaft seals probably install from the inside of the cover and might have a flange, so be careful.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
The following user(s) said Thank You: wireman

Please Log in or Create an account to join the conversation.

  • lewisj
  • lewisj's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 141
  • Thanks: 4

Re: transmission troubles?

10 Oct 2011 08:48
#482304
MFolks,
Thanks for the help! Sounds like a good weekend project. I will gather the gaskets and seals and set aside some time. Thanks again for the help!
Jim
1973 Z1
1075cc MTC kit
Andrews 3X cams
ZRX 1200 swingarm

Vance&Hines header/ exhaust
29mm smoothbores w/pods
ZR7S 41mm Front Forks with 17" wheels

Please Log in or Create an account to join the conversation.

  • testarossa
  • testarossa's Avatar
  • Offline
  • User
  • User
    Registered
  • Attack life, it's only trying to kill you.
  • Posts: 3673
  • Thanks: 83

Re: transmission troubles?

10 Oct 2011 09:05
#482307
Good advice from Mfolks as usual. I would bet that you lost your return spring on the shifter. It should be an easy fix, once you get past those covers.
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum