Bike won't start.

  • sham
  • sham's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 129
  • Thanks: 1

Bike won't start.

10 Oct 2011 07:11 - 10 Oct 2011 07:19
#482298
Hey - not quiet sure which of the categories this fits into - its a bit of a generic I don't know what's going on question...

So finally managed to clean out the tank on the weekend - let it sit in white vinegar for a night, then high pressure hosed most of the rust off before neutralizing with bi carb soda, running meth through it, then rinsing with 2 stroke and petrol mix and finally doing a couple rounds of petrol to shake out the loose flakes...

I filled her up with a bit of petrol and hit the starter - the new ignition, which produces sparks I'm sure did its thing, but all I got was a strange "burping" kind of sound from the exhaust, along with the usual starter motor sound (I think)...

So would anyone have any suggestions on what might be wrong and what I might look at? I'll attach a video of the spark so you can see if its sufficient, along with a video of me trying to start the thing - you'll hear the sound resembling what I mentioned in the last segment of the video...

Thanks in advance.

[IMG


[IMG
Last edit: 10 Oct 2011 07:19 by sham.

Please Log in or Create an account to join the conversation.

  • testarossa
  • testarossa's Avatar
  • Offline
  • User
  • User
    Registered
  • Attack life, it's only trying to kill you.
  • Posts: 3673
  • Thanks: 83

Re: Bike won't start.

10 Oct 2011 09:24
#482310
I clicked the link to your project thread, and it looks like you went through the carb, right? Did you spray aerosol carb cleaner through all the jet ports to verify that there were no blockages? Did you replace all of the faulty rubber bits such as the carb boot? Is the diaphragm in good shape?

It appears from your video that your ignition is working, but is it timed correctly?

I'm not familiar with the 250, so hopefully someone with experience will chime in with proper timing info, or hopefully you have a service manual that you can reference for procedures.

Valves adjusted properly?

Do you have compression?

Sorry, I'm just throwing out ideas since I'm not familiar with that model or your particular project in general.
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Bike won't start.

10 Oct 2011 09:52
#482319
Maybe the Enricher circuit in the carb is still plugged? Can you Tickle it with a bit of gas down the plug hole, or in the back of the carb?
Is the Airbox connected?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • sham
  • sham's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 129
  • Thanks: 1

Re: Bike won't start.

11 Oct 2011 07:18 - 11 Oct 2011 08:52
#482514
Thanks for the replies.

Yeh the carb itself was pretty clean, but I did spray brake cleaner through it and it seemed ok - I didn't replace things like carb boots (which are very stiff). The diaphragm I left - it seemed ok to me. Not that sure about the valves etc - they were working but I did the carb stuff without the manual and it was the first bit of motorcycle I ever touched - I ended up stripping the copper or whatever coating from the drain pipe =S sounds like I should check or that?

I'm not sure how to check the timing to be honest - the manual says I'm to use a timing inspection cover (special tool), which also requires the bike to be at 2,100 rpm and 4,500 rpm...

I actually took out the air box filter as it was all rusted, and I have not been able to find a replacement sponge thing. I was looking at pods instead, but the air box is still in place.

A suggestion has also been made for me to check the float, and this makes me think I need to check the drain screw - that's the one which I was suppose to remember how far it was screwed in correct?

I'll give it a go and share the results.

Thanks.
Last edit: 11 Oct 2011 08:52 by sham.

Please Log in or Create an account to join the conversation.

  • sham
  • sham's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 129
  • Thanks: 1

Re: Bike won't start.

11 Oct 2011 08:52 - 11 Oct 2011 08:55
#482517
Ok, so I being the idiot I am didn't read the manual properly before removing the carb from its tight nesting spot, but here are some interesting points which I think I can work off.

I undid the drain screw, but only a couple drops of petrol came out. This to me meant that there wasn't much fuel getting into the float, so I took the carb out. In my head, I was looking for was the "thing" which you're suppose to count how many turns it was to tighten (pilot screw) but I thought it was a jet.

So dismanted the float and found that petrol had been in it, but that it hadn't reached the carb bore. So I went about looking for this "thing". Finally found it scanning the manual and realized it was on the exterior body...

Anyways, below is a diagram from the manual which shows that the pilot screw as an integral part of the air supply / starter system, so my question would be, given that there is evidence of petrol in the float bowl, but not enough to be gushing out when I loosen the drain screw - that there was no evidence of petrol reaching the carb body, is the pilot screw my most obvious culprit for now? And does anyone know how tight it should be / how many turns should I screw it in to? Also I don't actually have a pilot screw plug - is this an issue?

[IMG


It will take me about an hour just to get the carb back into place to check my theory, so I want to make sure I'm not totally off track before I do it lol.

Thanks.
Last edit: 11 Oct 2011 08:55 by sham.

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Bike won't start.

11 Oct 2011 09:12 - 11 Oct 2011 09:25
#482523
As far as the Pilot Screw goes, there should be a setting in your manual for the # of turns from Lightly seated, some thing like 1 3/4- 2 turns. This is only a starting point and will require adjustment one the bike is up to temp.
Fuel level in the bowl is critical, if you don't have the fuel entering the bowl, through the float valve needle/ seat, and getting up to just below the gasket surface, it won't work properly. Connect your fuel line from the tank, with the bowl off, and make sure gas flows out of the carb. Lift the float up and it should stop flowing. If that's ok then Go back to having the bowl in place. You should be able to open the drain screw and have fuel come out. If not the small hole there might be plugged. So the way to check the Fuel Level in the bowl, is with a piece of clear tubing attached to the drain, and run along the side of the carb body pointing up. Open the screw with the Fuel turned to "Prime" and it should rise up the tube showing the Fuel Level. Its a very simple sight gauge. If not Just below the Gasket surface, then you need to adjust the float by bending the small Tang where the needle contacts.




Attachment not found

1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 11 Oct 2011 09:25 by Motor Head.

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Bike won't start.

11 Oct 2011 10:02
#482530
"I'm not sure how to check the timing to be honest - the manual says I'm to use a timing inspection cover (special tool), which also requires the bike to be at 2,100 rpm and 4,500 rpm..."
Yes to be right you need a strobe timing light, with Inductive pick-up to flash each time it sparks.
There is a mark on the engine/ head, and then there should be a "F" on the Rotor. These should line up at Idle speed when the light is flashing. If you only fitted the new CDI Box and didn't disassemble the Head, Plate, Rotor, then it is still in the same place as before. Idle timing probably OK, but would need checking. Full Advance of the Ignition timing would also be good to check. There should be a couple of lines/ marks close together farther to the right on the Rotor. When the engine hits 4500RPM then one of these should line up to the Mark on the Engine/ head.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Bike won't start.

11 Oct 2011 10:07
#482533
I also read back and found where you PODDED, well the bike was set up for the Airbox unless you changed some of the Jetting. It is probably Lean, making it a Bitch to start. Try priming the plug hole with a small amount of Petrol and see if it will start. Just a Tea spoon will make it Fire. Of course Down Under you Have the "Start You Bastard" brand of Ether. Ether is not my choice, but a shot of that in the Carb might do it.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • sham
  • sham's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 129
  • Thanks: 1

Re: Bike won't start.

12 Oct 2011 08:03
#482723
Hey Motor Head - thanks for the replies and taking time to go through my thread - I haven't actually podded yet, though that's what I'm leaning towards, as I'm missing the sponge material in my box filter at the moment and it will cost more to replace the whole thing than to go the way of the pods...I found an earlier thread on this site which seemed to identify which size jet to use, so I was going to base it off that, but for now, the air box is still installed.

Going to be flat out till weekend with work, so I'll try to do as you suggested with the carb then. Would you have any suggestions as to how to get the carb back into the boots easily? They are extremely stiff - literally took about an hour last time. I've read that I can soften them up by using a hair dryer, but I think I'll have to get a new set somewhere down the line.

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Bike won't start.

12 Oct 2011 09:40
#482728
Well If you Really want to head in the POD direction, then you probably don't want to spend for the new Airbox Boot. But the Manifold/ Carb holder, if it is really hard it may be cracked already. Without the rear support of the Airbox boot, it may crack or separate. A new Manifold/ Carb Holder would be a good call.
As far as I suggested for giving it a bit of petrol to see if it will start, you can add to the plug hole, or the small vacuum fitting on the Manifold/ carb holder. That way you don't have to pull the carb/ boots.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • sham
  • sham's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 129
  • Thanks: 1

Re: Bike won't start.

13 Oct 2011 08:50
#482896
Cool, I'll try doing that. When I said I was busy till the weekend I didn't expect to be this busy, but definitely looking forward to it. Can you just clarify what the plug hole is? Is that the end of the bore which connects to the air box?

Thanks for all the help so far.

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Bike won't start.

13 Oct 2011 09:23
#482902
Spark plug hole. ;)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum