No compression
- gotakz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 28
- Thanks: 0
Re: No compression
13 Oct 2011 23:16
I re-set the timing and and still zero compression across all cylinders next I'll check valve clearances and start looking for a shop to do the head.
1976 Kz900-A4
Had a 1985 Gpz750
Had a 1985 Gpz750
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: No compression
14 Oct 2011 09:30
"zero compression across all cylinders"... :blink:
I guess it's possible but highly unlikely that all 4 would truly measure 0 cmHg.
You positive this gauge works correctly... Test on another vehicle for confirmations...
I guess it's possible but highly unlikely that all 4 would truly measure 0 cmHg.
You positive this gauge works correctly... Test on another vehicle for confirmations...
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: No compression
14 Oct 2011 09:56
Put you finger over the spark plug hole, and it should blow it off of it. The gauge will have a valve core in it at the fitting end. If this fails, the gauge will show pressure as each compression stroke occurs, but lose it between strokes. Or if the valve is missing.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- gengomerpyle
-
- Offline
- User
-

Registered
- Posts: 616
- Thanks: 17
Re: No compression
14 Oct 2011 18:00
i was going to say the same thing about putting a finger over the plug hole.
Motor Head wrote: Put you finger over the spark plug hole, and it should blow it off of it. The gauge will have a valve core in it at the fitting end. If this fails, the gauge will show pressure as each compression stroke occurs, but lose it between strokes. Or if the valve is missing.
1982 GPZ750R1 ELR
1978 Honda CB750F SuperSport
1971 Honda CB750K
1970 Honda CL100 Scrambler
1978 Honda CB750F SuperSport
1971 Honda CB750K
1970 Honda CL100 Scrambler
Please Log in or Create an account to join the conversation.
- gotakz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 28
- Thanks: 0
Re: No compression
14 Oct 2011 23:26
Put my finger over plug hole and it doesn't blow it off but I can feel air blowing out.
1976 Kz900-A4
Had a 1985 Gpz750
Had a 1985 Gpz750
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: No compression
14 Oct 2011 23:32
Do you have an air compressor and a rubber tipped blow gun? Or a Leak Down Tester?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- gotakz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 28
- Thanks: 0
Re: No compression
15 Oct 2011 04:16
Yes I have a compressor and rubber tip blow gun...
1976 Kz900-A4
Had a 1985 Gpz750
Had a 1985 Gpz750
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: No compression
15 Oct 2011 09:35
The shade tree leak down tester ---
With both valves closed, introduce compressed air through the spark plug hole, turn off the compressor while keeping the rubber tip tightly pressed into the spark plug hole, and try listening to where the compressed air escapes. Which will typically be heard at the exhaust (exhaust valve not fully seating) or at the carb (intake valve not fully seating) or at the crank case vent (worn piston, rings, cylinder bore) or sometimes from a leak in the head gasket.
Good Fortune!
With both valves closed, introduce compressed air through the spark plug hole, turn off the compressor while keeping the rubber tip tightly pressed into the spark plug hole, and try listening to where the compressed air escapes. Which will typically be heard at the exhaust (exhaust valve not fully seating) or at the carb (intake valve not fully seating) or at the crank case vent (worn piston, rings, cylinder bore) or sometimes from a leak in the head gasket.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: No compression
15 Oct 2011 10:43That's it. I'll just add that the Piston should be at TDC (Top Dead Center) up on the compression Stroke, that's both valves closed. Or when the Air is applied the engine will turn/ roll over.Patton wrote: The shade tree leak down tester ---
With both valves closed, introduce compressed air through the spark plug hole, turn off the compressor while keeping the rubber tip tightly pressed into the spark plug hole, and try listening to where the compressed air escapes. Which will typically be heard at the exhaust (exhaust valve not fully seating) or at the carb (intake valve not fully seating) or at the crank case vent (worn piston, rings, cylinder bore) or sometimes from a leak in the head gasket.
Good Fortune!
Did you every check your valve clearances?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- gotakz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 28
- Thanks: 0
Re: No compression
24 Oct 2011 16:36
Long story short on why it came apart....I found out the hard way that I had a faulty timing chain tensioner when I broke 2 exhaust valves I changed them and I was still jumping teeth on the cams when I cranked it over by hand seemed like it was jumping at the crank so I found A used bottom end the changed valves were used but in good shape.
I've noticed that the spark advancer pictured in the Z1 manual I got off this site does not look like the one from my 900...the markings are different would that matter.
I've noticed that the spark advancer pictured in the Z1 manual I got off this site does not look like the one from my 900...the markings are different would that matter.
1976 Kz900-A4
Had a 1985 Gpz750
Had a 1985 Gpz750
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: No compression
24 Oct 2011 17:05
T is top dead center when the T mark is aligned with the permanent case mark.
The ignition timing (F marks and higher rpm marks) are irrelevant to cam timing.
Good Fortune!
The ignition timing (F marks and higher rpm marks) are irrelevant to cam timing.
Attachment advancerstyles.jpg not found
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
The following user(s) said Thank You: gotakz
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
