Problem engaging clutch
- Archiddeon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 114
- Thanks: 1
Problem engaging clutch
14 Oct 2011 02:24
Trying to restore my 1983 GPZ 550, finally got the engine running (yay!) so now onto other things ... the clutch lever is very loose and didn't feel like it engaged when pulled (no resistance). Maxxing out the adjustment had no effect.
I pulled off the sprocket cover on the left side, disassembled and greased the push rod actuator (the little cylinder mounted on the plate of three ball bearings that the clutch cable pulls on), reassembled ... no dice, same thing.
Ok, maybe the clutch is jammed on the other end (This bike hadn't run for 2 years, so who knows). Drain the oil and pull off the clutch cover on the right side ... all looks good. Very little wear is apparent, no burning smell, all springs present and accounted for, the little steel ball between the push rod and that little end piece is still there ... hrmmm. Reassemble and try again ... still no clutch engagement.
Remove the sprocket cover, put a small glob of grease on the left end of the push rod and replace the cover ... pull the clutch a few times (it doesn't spring back, so has to be pushed back) and off with the cover again. The glob is untouched ... so the end of the push rod is not even touching the inside of the actuator.
Sooo ... any suggestions? Is there some way to adjust the push rod or the actuator? Is there something I could test to further pinpoint the problem?
Thanks!
I pulled off the sprocket cover on the left side, disassembled and greased the push rod actuator (the little cylinder mounted on the plate of three ball bearings that the clutch cable pulls on), reassembled ... no dice, same thing.
Ok, maybe the clutch is jammed on the other end (This bike hadn't run for 2 years, so who knows). Drain the oil and pull off the clutch cover on the right side ... all looks good. Very little wear is apparent, no burning smell, all springs present and accounted for, the little steel ball between the push rod and that little end piece is still there ... hrmmm. Reassemble and try again ... still no clutch engagement.
Remove the sprocket cover, put a small glob of grease on the left end of the push rod and replace the cover ... pull the clutch a few times (it doesn't spring back, so has to be pushed back) and off with the cover again. The glob is untouched ... so the end of the push rod is not even touching the inside of the actuator.
Sooo ... any suggestions? Is there some way to adjust the push rod or the actuator? Is there something I could test to further pinpoint the problem?
Thanks!
1983 GPz 550
1985 Honda CH150 Scooter
1995 Suzuki GS500E
1985 Honda CH150 Scooter
1995 Suzuki GS500E
Please Log in or Create an account to join the conversation.
- clutch
-
- Offline
- User
-

Registered
- I wish I had a tad more patience to do it better!
- Posts: 1051
- Thanks: 13
Re: Problem engaging clutch
14 Oct 2011 02:34
Most of our clutch cables adjust tighter as we "unscrew" the adjustment mechanism. Are you turning this the correct way? I'm not sure about the 550, but my 750 has a pushrod adjustment on the engine sprocket cover. There is a small rectangular piece held on by 2 screws. If you remove this there is an adjustment nut. Again, I'm not sure if your bike had this, but your repair manual would be able to help you there as well.
Southern Maryland, USA
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
Please Log in or Create an account to join the conversation.
- Archiddeon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 114
- Thanks: 1
Re: Problem engaging clutch
14 Oct 2011 02:47
Yeah yeah yeah! Thanks, Clutch
... ironic? 
I sat there for a while trying to figure out which way to lengthen or shorten the chain. Didn't know what the little screw head under the sprocket cover plate was for though! I'm certain this is it. Will try it out tomorrow and report the results
I sat there for a while trying to figure out which way to lengthen or shorten the chain. Didn't know what the little screw head under the sprocket cover plate was for though! I'm certain this is it. Will try it out tomorrow and report the results
1983 GPz 550
1985 Honda CH150 Scooter
1995 Suzuki GS500E
1985 Honda CH150 Scooter
1995 Suzuki GS500E
Please Log in or Create an account to join the conversation.
- clutch
-
- Offline
- User
-

Registered
- I wish I had a tad more patience to do it better!
- Posts: 1051
- Thanks: 13
Re: Problem engaging clutch
14 Oct 2011 02:49
Sounds like you figured out what you need. Make sure you check the specs in your manual for proper pushrod adjustment. Glad I could help
Southern Maryland, USA
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: Problem engaging clutch
14 Oct 2011 09:11
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
The following user(s) said Thank You: clb3carl
Please Log in or Create an account to join the conversation.
- TexasKZ
-
- Offline
- Platinum Member
-

Registered
- Posts: 8420
- Thanks: 2804
Re: Problem engaging clutch
14 Oct 2011 11:25
FYI - Pulling the lever DIS-engages the clutch and releasing the lever ENgages it.
1982 KZ1000 LTD parts donor
1981 KZ1000 LTD slowly moving toward resurrection
2000 ZRX1100 not ridden enough
www.kzrider.com/forum/11-projects/620336...amateur-build-thread
1981 KZ1000 LTD slowly moving toward resurrection
2000 ZRX1100 not ridden enough
www.kzrider.com/forum/11-projects/620336...amateur-build-thread
Please Log in or Create an account to join the conversation.
- Archiddeon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 114
- Thanks: 1
Re: Problem engaging clutch
16 Oct 2011 16:45 - 16 Oct 2011 16:45
Hehe, thanks Texas 
Problem has been resolved. On the left side of the bike, on the sprocket cover was the rectangular cover plate secured by two bolts. Underneath was the clutch adjustment screw. Set it according to the manual (tight then back off 1/2 turn) ... noting that clockwise LOOSENS and counter-clockwise TIGHTENS. Adjusted the cable free play a bit and now the clutch is good to go
Thank-you :laugh:
Problem has been resolved. On the left side of the bike, on the sprocket cover was the rectangular cover plate secured by two bolts. Underneath was the clutch adjustment screw. Set it according to the manual (tight then back off 1/2 turn) ... noting that clockwise LOOSENS and counter-clockwise TIGHTENS. Adjusted the cable free play a bit and now the clutch is good to go
Thank-you :laugh:
1983 GPz 550
1985 Honda CH150 Scooter
1995 Suzuki GS500E
1985 Honda CH150 Scooter
1995 Suzuki GS500E
Last edit: 16 Oct 2011 16:45 by Archiddeon.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
