Cam Chain Issues

  • rockabillybobber420
  • rockabillybobber420's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 4
  • Thanks: 0

Cam Chain Issues

14 Oct 2011 02:41
#483099
Hey everyone I have run into another problem with my 1980 KZ1000E2. I am just finishing up a head gasket replace and am having issues with re-assembly of my camshafts/chain. After installing the exhaust an intake cam shafts there seems to be no slack in the chain at all. I have tried to install the tensioner and there is not enough slack to get the bolts started. Im thinking there might be a kink in the chain in the bottom end.
Any help will be greatly appreciated!

Please Log in or Create an account to join the conversation.

  • Chaotic Reason
  • Chaotic Reason's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 384
  • Thanks: 15

Re: Cam Chain Issues

14 Oct 2011 04:51
#483106
Are you using the Kawasaki FSM as your reference? I'm going to have to do the same to my E2 and am wondering if I might run into the same issue?
As I was reading about how to do the re-install, something caught my eye and am wondering about it for you. What tensioner are you using? The stock, automatic one? Or a manual one? From my understanding, the springs can be a bit of a beast to try to keep compressed so that the tensioner goes into its own housing as much as possible while installing. And then of course, you have to remove the item you were using to keep the spring compressed. I love a good puzzle!
Michael
1980 KZ1000 shaft drive

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: Cam Chain Issues

14 Oct 2011 14:27
#483169
probably balled up under crank sprocket,having bike on center stand makes life much easier B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: Cam Chain Issues

14 Oct 2011 19:28
#483222
wireman wrote: probably balled up under crank sprocket,having bike on center stand makes life much easier B)

X2
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • rockabillybobber420
  • rockabillybobber420's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 4
  • Thanks: 0

Re: Cam Chain Issues

15 Oct 2011 22:55
#483426
Yeah thats what I was hoping it wouldnt be! Oh well sounds like fun, atleast I have all winter to get it figured out. Im guessing im going to have to tear the motor down to the block? Not sure if this is something I really want to dive into or not!

Thanks for the help!

Please Log in or Create an account to join the conversation.

  • TeK9iNe
  • TeK9iNe's Avatar
  • Offline
  • User
  • User
    Registered
  • What did you do!?!
  • Posts: 2436
  • Thanks: 28

Re: Cam Chain Issues

15 Oct 2011 23:11
#483431
Remove the valve cover and the cams/rollers/quides necesary to look down the center of the engine at the crank gear the chain runs on. You should be able to use a long screw driver and by gently pulling the chain back and forth and with some screwdriver work, you can get it back in place where need be.
You'll need lots of steady light.

Good luck

B)
Motorcycle Shop Owner/Operator

79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors ;)

Please Log in or Create an account to join the conversation.

  • bls5050
  • bls5050's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 34
  • Thanks: 2

Re: Cam Chain Issues

16 Oct 2011 09:25
#483485
I went through the same thing when I rebuilt my motor earlier this year. Take the above-mentioned steps to ensure that the chain isn't balled up. Also, it is possible for the chain to sit right next to the crank sprocket. It will still spin the crank when you pull on it, but it feels notchy, not smooth. Because of the design of the chain tensioner, you will never be able to just push it into the back of the motor without resetting it as per the factory manual. When you get it right, though, it just seems to drop in place. When you release the spring in the tensioner, it snaps forward with enough force to pull your cams around if they aren't lined up properly. If I recall, it took me several frustrating tries to get everything lined up and sitting properly, with the chain slack in the right area.
1980 KZ1000st

Please Log in or Create an account to join the conversation.

  • rockabillybobber420
  • rockabillybobber420's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 4
  • Thanks: 0

Re: Cam Chain Issues

17 Oct 2011 02:21
#483697
Thanks for all the help, Im going to try an take a crack at it tomorow! Hopefully it's not off the crank gear, and wont need me to pull off the cyl head again! (feels like i've pulled it off a 100 times already!!) Tek I see your from St.Cats eh! Im in London, hopefully I can get this fixed an get a ride in before the snow starts!

Thanks again!

Please Log in or Create an account to join the conversation.

  • 531blackbanshee
  • 531blackbanshee's Avatar
  • Offline
  • Vendor
  • Vendor
    Vendors
  • Posts: 7442
  • Thanks: 796

Re: Cam Chain Issues

17 Oct 2011 11:59
#483738
you do not have to pull the head to check that the cam chain is on the crank gear.just the cams and upper idler.

leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!

billybiltit.blogspot.com/

www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work

kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum