Yet another "bike won't start" query
- Archiddeon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 114
- Thanks: 1
Yet another "bike won't start" query
16 Oct 2011 16:42
Not wanting to hijack someone else's thread for this, I figured I would just start a new one.
So my 1983 GPZ550 hasn't run in about 2-3 yrs. I went through all of the wiring and the carbs (disassembled and cleaned ... though not as fully as I should have I now know after reading some of the carb cleaning guides posted), replaced the old leaking fuel lines changed the oil and stuck in some fresh new spark plugs.
Just laying the wiring harness on top of the bike and plugging everything in, I gave it a try and the bike fired up! Ran surprisingly smoothly and only on full choke, seemed to be firing on all cylinders with no apparent misfires ... yay!
Now the problem ...
I wired the harness back on, properly routing it around the frame. Tried to start it and no joy
Turns over fine, but just won't fire up ... not even a little burp or stumble!
Did the usual diagnostics ...
1) Fuel - Got clear fuel lines, so can see the line from the gas tank to the carbs is full
2) Spark - Pulled the plugs and they all have sparks (clearly visible even in daylight)
3) Compression - Bit dodgey here, dry values are 120, 95, 110, 115 (first time measuring properly, so not sure how accurate these are). Wet values (teaspoon or so of oil in the plug hole) are all over 250.
Sooooo .... the piston rings probably need replacing, but why won't the bike start now when it did before? Am I overlooking something obvious here?
Thanks!
So my 1983 GPZ550 hasn't run in about 2-3 yrs. I went through all of the wiring and the carbs (disassembled and cleaned ... though not as fully as I should have I now know after reading some of the carb cleaning guides posted), replaced the old leaking fuel lines changed the oil and stuck in some fresh new spark plugs.
Just laying the wiring harness on top of the bike and plugging everything in, I gave it a try and the bike fired up! Ran surprisingly smoothly and only on full choke, seemed to be firing on all cylinders with no apparent misfires ... yay!
Now the problem ...
I wired the harness back on, properly routing it around the frame. Tried to start it and no joy
Did the usual diagnostics ...
1) Fuel - Got clear fuel lines, so can see the line from the gas tank to the carbs is full
2) Spark - Pulled the plugs and they all have sparks (clearly visible even in daylight)
3) Compression - Bit dodgey here, dry values are 120, 95, 110, 115 (first time measuring properly, so not sure how accurate these are). Wet values (teaspoon or so of oil in the plug hole) are all over 250.
Sooooo .... the piston rings probably need replacing, but why won't the bike start now when it did before? Am I overlooking something obvious here?
Thanks!
1983 GPz 550
1985 Honda CH150 Scooter
1995 Suzuki GS500E
1985 Honda CH150 Scooter
1995 Suzuki GS500E
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Yet another "bike won't start" query
16 Oct 2011 17:03 - 16 Oct 2011 17:08
Would double-check for correct connections of signal wires (from the Igniter) to ignition coils to assure the wires aren't reversed.
Signal wires should be color coded, with signal wire from left-hand 9 o'clock pick-up coil going through the igniter to (guessing black wire) whichever ignition coil is firing the outside spark plugs. And signal wire from right-hand 3 o'clock pick-up coil going through the igniter to (guessing green wire) whichever ignition coil is firing the inside spark plugs.
Also assure that one ignition coil is firing the two outside spark plugs #1 and #4, and that the other ignition coil is firing the inside spark plugs #2 and #3.
Good Fortune!
Signal wires should be color coded, with signal wire from left-hand 9 o'clock pick-up coil going through the igniter to (guessing black wire) whichever ignition coil is firing the outside spark plugs. And signal wire from right-hand 3 o'clock pick-up coil going through the igniter to (guessing green wire) whichever ignition coil is firing the inside spark plugs.
Also assure that one ignition coil is firing the two outside spark plugs #1 and #4, and that the other ignition coil is firing the inside spark plugs #2 and #3.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 16 Oct 2011 17:08 by Patton.
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Yet another "bike won't start" query
16 Oct 2011 17:13
Ohm Checking Pickup(Pulsing) Coils
The pickup coils on the Kawasaki’s with the factory supplied electronic ignition can sometimes fail or become intermittent due to heat and vibration.
1.Trace back from where the pick up coils are mounted,(under a right side CD sized cover) locate and disconnect a small 4 pin connector. Using a multi-meter set on OHMS and range of 2K, check between the BLUE and BLACK wires(#1 and #4 sparkplug wires) for between 360- 540 OHMS.
2.For #2 and #3 sparkplugs the wire colors will be YELLOW and RED, again 360-540 OHMS. The 550’s,650’s & 750’s may be backwards to the Z1’s,Kz900’s,Kz1000’s & Kz1100’s.
3.If the pickup coils are suspect of failing due to heat, they can be stressed using a hair dryer without the need of the engine running.
4.A replacement set of pickup coils might be obtained from a dealer who serviced the police Kawasaki’s.
5. If replacement pickup coils are not available, your next choice would be to order a Dyna “S” electronic ignition system from www.z1enterprises.com It replaces the IC igniter with a smaller module located where the mechanical ignition advancer was mounted.
6. Checking with Kawasaki.com website has determined that the Pick up(pulsing) coils are available . The pulsing coil # is 59026-1133 and replaces the older # 1002, 1012 which were used from the MKII motors until the 2005 P24.
7.Check the small 4 pin connector that the pickup coils connect to for corrosion/loose pins too.
The pickup coils on the Kawasaki’s with the factory supplied electronic ignition can sometimes fail or become intermittent due to heat and vibration.
1.Trace back from where the pick up coils are mounted,(under a right side CD sized cover) locate and disconnect a small 4 pin connector. Using a multi-meter set on OHMS and range of 2K, check between the BLUE and BLACK wires(#1 and #4 sparkplug wires) for between 360- 540 OHMS.
2.For #2 and #3 sparkplugs the wire colors will be YELLOW and RED, again 360-540 OHMS. The 550’s,650’s & 750’s may be backwards to the Z1’s,Kz900’s,Kz1000’s & Kz1100’s.
3.If the pickup coils are suspect of failing due to heat, they can be stressed using a hair dryer without the need of the engine running.
4.A replacement set of pickup coils might be obtained from a dealer who serviced the police Kawasaki’s.
5. If replacement pickup coils are not available, your next choice would be to order a Dyna “S” electronic ignition system from www.z1enterprises.com It replaces the IC igniter with a smaller module located where the mechanical ignition advancer was mounted.
6. Checking with Kawasaki.com website has determined that the Pick up(pulsing) coils are available . The pulsing coil # is 59026-1133 and replaces the older # 1002, 1012 which were used from the MKII motors until the 2005 P24.
7.Check the small 4 pin connector that the pickup coils connect to for corrosion/loose pins too.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- Archiddeon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 114
- Thanks: 1
Re: Yet another "bike won't start" query
16 Oct 2011 18:31
The pickup coils are wired black and blue for the 9 o'clock (rear) one and red and yellow for the 3 o'clock (front) one. These connect up through the a single 4-pin connector to the ic igniter component and the wires coming out are green (which goes to the "negative" terminal of the left coil firing plugs 2 and 3), black (goes to the "positive" terminal of the right coil firing plugs 1 and 4), yellow/red (which goes to both of the two coils) and yellow black (which heads off somewhere else in the harness).
I drained the carbs and confirmed that all 4 have fuel in them and the floats are working. I have not checked the float level.
I have not yet checked the resistance of the pickup coils.
What perplexes me is that the bike was running and that everything still seems to be working. Without testing them with a multimeter (mine is at work) is there a way to tell if the pickup coils are busted? Would the plugs fire at all if they were faulty?
I drained the carbs and confirmed that all 4 have fuel in them and the floats are working. I have not checked the float level.
I have not yet checked the resistance of the pickup coils.
What perplexes me is that the bike was running and that everything still seems to be working. Without testing them with a multimeter (mine is at work) is there a way to tell if the pickup coils are busted? Would the plugs fire at all if they were faulty?
1983 GPz 550
1985 Honda CH150 Scooter
1995 Suzuki GS500E
1985 Honda CH150 Scooter
1995 Suzuki GS500E
Please Log in or Create an account to join the conversation.
- Archiddeon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 114
- Thanks: 1
Re: Yet another "bike won't start" query
16 Oct 2011 18:46
Haha! The bike starts
Pulled the 4-pin connector apart, sprayed in some contact cleaner, put it back together and with a little turning over, she took 
BUT
Only on two cylinders
The spray-water-on-the-headers test showed only cylinders 1 and 2 firing ... nothing from 3 and 4
Any ideas?
BUT
Only on two cylinders
The spray-water-on-the-headers test showed only cylinders 1 and 2 firing ... nothing from 3 and 4
Any ideas?
1983 GPz 550
1985 Honda CH150 Scooter
1995 Suzuki GS500E
1985 Honda CH150 Scooter
1995 Suzuki GS500E
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Yet another "bike won't start" query
16 Oct 2011 18:51
The pick up coils tell the IC igniter to give the ignition coils their grounds, firing the sparkplugs. Have you checked the input voltage to the ignition coils? They get power from the run/stop switch on the right handle bar.The wiring may be red or be red/yellow stripe.
Some of the older Kawasaki's owners are reporting crumbled soldered connections, so check your's for signs of joint failure/dirty connections.
The sparkplug caps contain a resistor for RFI supression, and can go bad after a number of years, they will unscrew from the sparkplug wires and should test at 5000 ohms.
Some of the older Kawasaki's owners are reporting crumbled soldered connections, so check your's for signs of joint failure/dirty connections.
The sparkplug caps contain a resistor for RFI supression, and can go bad after a number of years, they will unscrew from the sparkplug wires and should test at 5000 ohms.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- Archiddeon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 114
- Thanks: 1
Re: Yet another "bike won't start" query
16 Oct 2011 19:03
So to test power to the ignition coils, where would I measure? Disconnect (for the left side ignition coil for instance) the yellow/red line and the green line and measure the voltage while pressing the start-stop switch? Wouldn't this fluctuate up and down as the plugs are told to fire?
When I cleaned up the wiring I disassembled the hand controls and the soldering looks in decent condition. One wire was loose, but soldered it back on no problem.
I'll add checking the cap resistance to my list when I get my multimeter from work.
Any ideas why 3 and 4 wouldn't fire? The plug caps seem the most likely, but the plugs still fire (tested them and all 4 spark). The compression isn't good, but same sort of range as the other two cylinders.
Now the inner or outer pair not firing would make more sense.
Think it may be because it was sitting for so long I should just let the bike sit and idle on two cylinders and see if the others kick in at some stage?
Thanks
When I cleaned up the wiring I disassembled the hand controls and the soldering looks in decent condition. One wire was loose, but soldered it back on no problem.
I'll add checking the cap resistance to my list when I get my multimeter from work.
Any ideas why 3 and 4 wouldn't fire? The plug caps seem the most likely, but the plugs still fire (tested them and all 4 spark). The compression isn't good, but same sort of range as the other two cylinders.
Now the inner or outer pair not firing would make more sense.
Think it may be because it was sitting for so long I should just let the bike sit and idle on two cylinders and see if the others kick in at some stage?
Thanks
1983 GPz 550
1985 Honda CH150 Scooter
1995 Suzuki GS500E
1985 Honda CH150 Scooter
1995 Suzuki GS500E
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Yet another "bike won't start" query
16 Oct 2011 20:02
With the meter set on VDC,range of 20, put the Red probe on where the red or red/yellow wire goes and the Black probe on either a good frame ground place or the battery Negative terminal/post.
Run/stop switch to "Run", ignition switch to the "On" position and you should see battery voltage on the meter's display.
Run/stop switch to "Run", ignition switch to the "On" position and you should see battery voltage on the meter's display.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Yet another "bike won't start" query
16 Oct 2011 20:06
If the meter shows 10 volts or less on the ignition coils, and the battery is fully charged, then it's time to:
Clean Motorcycle Electrics
Get some of the De-Oxit electrical contact cleaner and figure on spending a good day going from the front of the bike to the back. It’s a plastic safe cleaner/preservative. www.deoxit.com is their website.
On the older Kawasaki's, a majority of electrical connectors are inside the headlight housing requiring removal of the headlight, then the fun begins.
Do one set of electrical connectors at a time to avoid mixing up what connects to where. Usually disconnecting, spraying with De-Oxit and reconnecting is about all you'll need.
However, when encountering the green crud of corrosion, a brass wire brush may be needed on the pins you can reach.Some 400-600 grit wet and dry sandpaper strips rolled into a tube should reach the male and female pins in the more difficult to clean connectors.
Smoker’s pipe cleaners, cotton swabs and wooden toothpicks work as cleaning aids.
Really small electrical connectors may require the use of a welders tip cleaning tool assortment.
Most pins in the connectors are coated with a thin plating of tin, and others may be nothing more than copper or brass.
If moisture is added, the resulting corrosion lowers the voltage/current being carried causing dim lights, slow engine cranking, slow turn signal responce and lower input voltage to the ignition coils resulting in weak spark.
The left and right handlebar switch pods will need attention too as they have circuit functions like turn, horn, run/stop, and start.
Usually a spritz or two with actuation of the switch is about all needed for these switches unless corrosion is detected and then careful disassembly is required.
The ignition switch may or may be not sealed to allow spraying the internal contacts. I urge caution if attempting to open this up as springs, and ball bearings may fly out never to be seen again!
If your bike has the older style glass tubed fuses, I suggest replacing them as vibration can cause internal failure. AGX is the type used, and most auto parts stores can get them for you.
Clean the fuse holder clips, looking for signs of overheating(discolored insulation, signs of melting).I use metal polish on a cotton swab, followed by spraying another clean swab with the De-Oxit and then rubbing the inside of the fuse clip.
All battery cables must be clean and tight for maximum current transfer. Check the cables going from the Negative(-) battery terminal/post to the engine mounting bolt
Also the one going from the Positive(+) terminal to the starter solenoid and from there to the starter motor.
If any battery cable feels ”Crunchy” when flexed, replace it as possible corrosion is inside the insulation.
Each "Bullet Connector" will have to be sprayed to ensure good connectivity, especially the ones going to the energizing coil of the starter solenoid.
The alternator output “Bullet Connectors” are usually behind the engine sprocket cover and will need inspecting and cleaning too.
The turn signal light sockets will benefit from a spritz from the contact cleaner along with the tail light/brake light socket.
Some brake light switches can be sprayed on the actuating rod, with the spray running down inside to the electrical contacts, others may be sealed requiring replacement if the switch is intermittent in operation.
Some people put the Di-Electric Grease on cleaned terminations/connectors, I don’t, as I’ve read/heard it can cause problems when it gets hot, actually insulating the connections, so the choice is yours to use or not.
I think I've covered about all of the electrical systems on the bike.........
Clean Motorcycle Electrics
Get some of the De-Oxit electrical contact cleaner and figure on spending a good day going from the front of the bike to the back. It’s a plastic safe cleaner/preservative. www.deoxit.com is their website.
On the older Kawasaki's, a majority of electrical connectors are inside the headlight housing requiring removal of the headlight, then the fun begins.
Do one set of electrical connectors at a time to avoid mixing up what connects to where. Usually disconnecting, spraying with De-Oxit and reconnecting is about all you'll need.
However, when encountering the green crud of corrosion, a brass wire brush may be needed on the pins you can reach.Some 400-600 grit wet and dry sandpaper strips rolled into a tube should reach the male and female pins in the more difficult to clean connectors.
Smoker’s pipe cleaners, cotton swabs and wooden toothpicks work as cleaning aids.
Really small electrical connectors may require the use of a welders tip cleaning tool assortment.
Most pins in the connectors are coated with a thin plating of tin, and others may be nothing more than copper or brass.
If moisture is added, the resulting corrosion lowers the voltage/current being carried causing dim lights, slow engine cranking, slow turn signal responce and lower input voltage to the ignition coils resulting in weak spark.
The left and right handlebar switch pods will need attention too as they have circuit functions like turn, horn, run/stop, and start.
Usually a spritz or two with actuation of the switch is about all needed for these switches unless corrosion is detected and then careful disassembly is required.
The ignition switch may or may be not sealed to allow spraying the internal contacts. I urge caution if attempting to open this up as springs, and ball bearings may fly out never to be seen again!
If your bike has the older style glass tubed fuses, I suggest replacing them as vibration can cause internal failure. AGX is the type used, and most auto parts stores can get them for you.
Clean the fuse holder clips, looking for signs of overheating(discolored insulation, signs of melting).I use metal polish on a cotton swab, followed by spraying another clean swab with the De-Oxit and then rubbing the inside of the fuse clip.
All battery cables must be clean and tight for maximum current transfer. Check the cables going from the Negative(-) battery terminal/post to the engine mounting bolt
Also the one going from the Positive(+) terminal to the starter solenoid and from there to the starter motor.
If any battery cable feels ”Crunchy” when flexed, replace it as possible corrosion is inside the insulation.
Each "Bullet Connector" will have to be sprayed to ensure good connectivity, especially the ones going to the energizing coil of the starter solenoid.
The alternator output “Bullet Connectors” are usually behind the engine sprocket cover and will need inspecting and cleaning too.
The turn signal light sockets will benefit from a spritz from the contact cleaner along with the tail light/brake light socket.
Some brake light switches can be sprayed on the actuating rod, with the spray running down inside to the electrical contacts, others may be sealed requiring replacement if the switch is intermittent in operation.
Some people put the Di-Electric Grease on cleaned terminations/connectors, I don’t, as I’ve read/heard it can cause problems when it gets hot, actually insulating the connections, so the choice is yours to use or not.
I think I've covered about all of the electrical systems on the bike.........
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- Archiddeon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 114
- Thanks: 1
Re: Yet another "bike won't start" query
16 Oct 2011 20:28
Cool cool ... I'll check this together with the pickup coil and spark plug cap resistances tomorrow and report my findings.
I'm just so glad the bike starts and runs again ... albeit on two cylinders.
I'm just so glad the bike starts and runs again ... albeit on two cylinders.
1983 GPz 550
1985 Honda CH150 Scooter
1995 Suzuki GS500E
1985 Honda CH150 Scooter
1995 Suzuki GS500E
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Yet another "bike won't start" query
16 Oct 2011 22:49 - 16 Oct 2011 22:50New plugs?Archiddeon wrote: ...1983 GPZ550...Pulled the plugs and they all have sparks (clearly visible even in daylight)....
Should be a fat blue spark.
Sometimes plugs show visible spark, but fail when under compression.
And this can happen with a new or relatively new plug.
Especially a plug that has been fuel-fouled.
Would install 4 brand new NGKB8ES spark plugs (or whatever plugs the FSM specifies) and re-test.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 16 Oct 2011 22:50 by Patton.
Please Log in or Create an account to join the conversation.
- Archiddeon
-
Topic Author
- Offline
- User
-

Registered
- Posts: 114
- Thanks: 1
Re: Yet another "bike won't start" query
16 Oct 2011 22:56
Thanks for the suggestion, Patton 
All four of the plugs are brand new, but I have heard of even new plugs being garbage.
When I pull the leads to check the resistances, I'll also try switch the plugs around (swap 1, 2 with 3, 4) and see if it makes any difference.
All four of the plugs are brand new, but I have heard of even new plugs being garbage.
When I pull the leads to check the resistances, I'll also try switch the plugs around (swap 1, 2 with 3, 4) and see if it makes any difference.
1983 GPz 550
1985 Honda CH150 Scooter
1995 Suzuki GS500E
1985 Honda CH150 Scooter
1995 Suzuki GS500E
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
