Carbon fouling? & possible causes

  • Topper
  • Topper's Avatar Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
    Registered
  • Posts: 1609
  • Thanks: 133

Carbon fouling? & possible causes

16 Oct 2011 18:48
#483567
Does this look like carbon fouling to you?

I'm going a couple months and a few thousand miles without running into trouble, but then my bike won't start and the plugs look like this.

Swap the plugs and I'm good to go.

What might be causing this?


Attachment plug.jpg not found

Permanent and perpetual noob.

1979 KZ750 Twin
2009 Kawasaki Versys

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Carbon fouling? & possible causes

16 Oct 2011 18:52
#483570
Rich on fuel or incomplete combustion. Maybe weak spark, or low cylinder pressure. Or just rich carburation.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Carbon fouling? & possible causes

16 Oct 2011 18:56
#483571
A "6" on a NGK sparkplugis pretty hot. Checked the sparkplug caps? They unscrew fom the sparkplug wire and should test at 5000 ohms. A resistor is inside, reducing the RFI when the plugs fire.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • Topper
  • Topper's Avatar Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
    Registered
  • Posts: 1609
  • Thanks: 133

Re: Carbon fouling? & possible causes

16 Oct 2011 19:02
#483573
MFolks wrote: A "6" on a NGK sparkplugis pretty hot. Checked the sparkplug caps? They unscrew fom the sparkplug wire and should test at 5000 ohms. A resistor is inside, reducing the RFI when the plugs fire.

Yeah my caps are good and the plugs are what's recommended in my manual.
Permanent and perpetual noob.

1979 KZ750 Twin
2009 Kawasaki Versys

Please Log in or Create an account to join the conversation.

  • Topper
  • Topper's Avatar Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
    Registered
  • Posts: 1609
  • Thanks: 133

Re: Carbon fouling? & possible causes

16 Oct 2011 19:09
#483576
Motor Head wrote: Rich on fuel or incomplete combustion. Maybe weak spark, or low cylinder pressure. Or just rich carburation.

I wouldn't doubt rich carburation. I had to go pretty rich on the air mix screws (almost all the way in) to eliminate some popping. I followed the advice given in other threads here about finding the point of highest idle on each cylinder. Worked like a charm to eliminate the popping. But now I seem to be too rich.

Also, the last time I took my carbs apart, I seem to remember the needle clip being in the top slot. Remind me, is that lean or rich?

This is a '79 KZ750 BTW.

And while I'm throwing questions at you... Rather than buying new plugs every time this happens, can I just remove the carbon and re-gap? Best way to remove it with a little sand paper?

Thanks.
Permanent and perpetual noob.

1979 KZ750 Twin
2009 Kawasaki Versys

Please Log in or Create an account to join the conversation.

  • jeffasaki
  • jeffasaki's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 996
  • Thanks: 44

Re: Carbon fouling? & possible causes

16 Oct 2011 19:12
#483577
short rides and worn valve stem seals
does it smoke a bit when cold?
had similar probs with one of my bikes
changed to iridium plugs
totally cured
i still take em out and clean em every so often
but always starts like a champ since i changed em out
i always try and make sure its hot after i park it
78 Z1R
78 KZ1000
76 KH500 gone
71 HS1B 90
81 GS 1100 gone
80 PE400
02 KLR


Ontario Canada

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Carbon fouling? & possible causes

16 Oct 2011 19:14 - 16 Oct 2011 19:20
#483581
By Top Groove, do you mean close to the needle taper, or away from the needle taper? What is the clip position, they are numbered 1-5, with 1 being the closest to the end and 5 being closest to the taper.
Carbon fouled plugs can be cleaned, the result can be mixed though. They have small sand blasting fixtures just for plug cleaning, I never liked them. What I do Is Burn it off. I get a Propane torch and heat it, then hit it on a hand wire brush, hit it with some brake clean and back to the torch. Burns off all the carbon which is what causes the spark to miss travel, instead of jumping the electrodes.

1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 16 Oct 2011 19:20 by Motor Head.

Please Log in or Create an account to join the conversation.

  • Topper
  • Topper's Avatar Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
    Registered
  • Posts: 1609
  • Thanks: 133

Re: Carbon fouling? & possible causes

16 Oct 2011 19:19
#483582
Motor Head wrote: By Top Groove, do you mean close to the needle taper, or away from the needle taper?

Away from the taper.
Permanent and perpetual noob.

1979 KZ750 Twin
2009 Kawasaki Versys

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Carbon fouling? & possible causes

16 Oct 2011 19:23
#483583
Ok so groove #1, the leanest setting for that Needle.
Refresh me what are you running, Pods or stock filter/ airbox?
Whats the Carbs and jet sizes? Did you increase from stock?
Hows the Fuel level in the float bowls?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • Godfrey
  • Godfrey's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 210
  • Thanks: 10

Re: Carbon fouling? & possible causes

16 Oct 2011 19:25
#483586
wow so that would mean the needle is as far down in the jet as the clip position will allow, in other words as lean as it will go.
1981 650CSR frame

1980 KZ750E engine

Please Log in or Create an account to join the conversation.

  • Topper
  • Topper's Avatar Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
    Registered
  • Posts: 1609
  • Thanks: 133

Re: Carbon fouling? & possible causes

16 Oct 2011 19:48
#483595
Motor Head wrote: Refresh me what are you running, Pods or stock filter/ airbox?
Whats the Carbs and jet sizes? Did you increase from stock?
Hows the Fuel level in the float bowls?

Stock airbox, stock jetting, fuel levels set with clear tube method.
Permanent and perpetual noob.

1979 KZ750 Twin
2009 Kawasaki Versys

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Carbon fouling? & possible causes

16 Oct 2011 19:53
#483598
Topper wrote:
Motor Head wrote: Refresh me what are you running, Pods or stock filter/ airbox?
Whats the Carbs and jet sizes? Did you increase from stock?
Hows the Fuel level in the float bowls?

Stock airbox, stock jetting, fuel levels set with clear tube method.
Well having the Needle set to its Leanest Setting is not normal. Position #3 is Stock, #4 would be if you are breathing a bit better, K&N 4-1 etc. #1 makes me think you have either the wrong jets of to high a float level.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum