Just finished cams

  • gwolever
  • gwolever's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 237
  • Thanks: 8

Just finished cams

17 Oct 2011 00:03
#483672
Hey guys. I just finished putting engine back together today. Just wanted to run a couple things by you to make sure did everything correctly:

1. After installing the cylinder head I checked the timing for the camshafts per manual. I had timing set at TDC for 1,4 pistons. Put the exhaust camshaft in first and made sure "EX" arrow was pointing forward and level with head surface. Then installed intake camshaft with "IN" arrow pointing to back of engine and level with the head surface. As per manual, I counted 44 pins from one arrow to the other. This left some slack in chain between camshafts, but no more than would be taken up by cam guide on top of valve cover.

2. I tightened down the cam caps and installed new gasket and then valve cover.

3. I installed cam chain tensioner with new spring and tightened it down. Then I put in the crosswedge and new spring and cap with washer and tightened. Everything went smoothly. The cam chain tensioner was a tight fit, but was easily able to get screws in and tighten it down. the crosswedge was out about 7mm like manual said when I put it in tensioner.

4. I was finishing engine by putting timing cover on and was tighten the smaller bolt (12mm?) and the crank move on me a little. Is this ok since the chain was all aligned and in proper timing setting with tensioner in place, or do I need to check chain/cams to make sure it is all still in right spot? Never done this before, so just wasn't sure. Should I be able to turn the crank using socket wrench on the larger bolt? And if so, should I try to put it back to TDC? Or am I just worrying about nothing and should just leave it alone?

Thanks guys. Sorry if these questions seem stupid.
1982 KZ1000 CSR

Please Log in or Create an account to join the conversation.

  • elfmagic17
  • elfmagic17's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 334
  • Thanks: 24

Re: Just finished cams

17 Oct 2011 00:17
#483675
As long as your guides and tensioner was installed and adjusted before it moved you should be golden, but it is a good idea to check alignment after manually turning the engine over to verify all lines up after guides and tensioner are installed and adjusted. I always check and recheck after to make sure nothing was "floating" on a tooth and not lined up properly. Last thing to go on should be valve cover IMO.
Kenny Hicks
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Just finished cams

17 Oct 2011 00:28
#483677
One other suggestion before hitting the starter button - I would remove the spark plugs and using the big nut on the crank (17 mm?) gently rotate the crank to make sure nothing like valves & pistons are hitting. With the plugs out it should rotate smoothly and easily. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • gwolever
  • gwolever's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 237
  • Thanks: 8

Re: Just finished cams

17 Oct 2011 10:11
#483727
Thanks guys.
1982 KZ1000 CSR

Please Log in or Create an account to join the conversation.

  • gwolever
  • gwolever's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 237
  • Thanks: 8

Re: Just finished cams

23 Oct 2011 23:34
#484983
650ed wrote: One other suggestion before hitting the starter button - I would remove the spark plugs and using the big nut on the crank (17 mm?) gently rotate the crank to make sure nothing like valves & pistons are hitting. With the plugs out it should rotate smoothly and easily. Ed

Thanks for the advice. I pulled the plugs and used the 17mm wrench to turn the crank. Turns smoothly and looking down into the spark plug holes, I saw that 1 and 4 pistons were at TDC exactly at the T 1-4 mark on the timing. Perfect.

Engine done for now. Now I start on the rest of the bike. Have a lot of work ahead of me, so I will be asking many more questions I'm sure. Next step is ordering seat, Hagons, tires, sprockets and chain, rotors, and sending headers to Jet-Hot coat.

Here's a couple of pics of engine all sealed up for now.

Attachment 020.JPG not found



Attachment 022.JPG not found



Attachment 021_2011-10-23.JPG not found

1982 KZ1000 CSR

Please Log in or Create an account to join the conversation.

  • Chaotic Reason
  • Chaotic Reason's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 384
  • Thanks: 15

Re: Just finished cams

23 Oct 2011 23:44
#484985
That's one shiny engine. Good work mate, I can't wait till I'm that far along! :)
Michael
1980 KZ1000 shaft drive

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Just finished cams

23 Oct 2011 23:49
#484989
These are strong engines, but remember to change the oil every 3000 miles(I do) and when they don't make a little noise, Worry!, as the valves may be running out of clearances.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Just finished cams

24 Oct 2011 00:37
#485000
A word to the wise. You probably should not be putting pictures of an engine you stole from a Kawasaki museum on the internet. :woohoo:
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Just finished cams

24 Oct 2011 09:45
#485030
650ed wrote: A word to the wise. You probably should not be putting pictures of an engine you stole from a Kawasaki museum on the internet. :woohoo:

Better lock that motor in your Gun Safe so its nice and comfy for the winter. ;)
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • gwolever
  • gwolever's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 237
  • Thanks: 8

Re: Just finished cams

24 Oct 2011 14:31
#485066
Thanks guys. I spent quite a bit of time on it. I think I will store this thing inside this winter. Can't wait til spring when I have it all done and able to ride it.
1982 KZ1000 CSR

Please Log in or Create an account to join the conversation.

  • gwolever
  • gwolever's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 237
  • Thanks: 8

Re: Just finished cams

24 Oct 2011 14:33
#485067
Looks a lot different from when I bought it back in July, that's for sure.
1982 KZ1000 CSR

Please Log in or Create an account to join the conversation.

  • mtbspeedfreak
  • mtbspeedfreak's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1413
  • Thanks: 36

Re: Just finished cams

24 Oct 2011 14:36
#485069
If it's sitting all winter, it may not hurt to squirt a few drops of motor oil in each cylinder to lubricate and prevent corrosion.
2000 ZRX 1100
1976 KZ 900- Daily Driver
1980 LTD 550- Dalton Highway survivor!

If it has tits or tires, it'll give you problems!

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum