Head Gasket
- Observer
-
Topic Author
- Offline
- User
-

Registered
- Posts: 13
- Thanks: 0
Head Gasket
17 Oct 2011 10:27
Tired of a minor oil weep through the head gasket, just in front by the (cam chain).
Thinking of replacing the Gasket, changing the studs etc.
What else should I do while I am at it?
Any advice
Thinking of replacing the Gasket, changing the studs etc.
What else should I do while I am at it?
Any advice
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Head Gasket
17 Oct 2011 11:09 - 17 Oct 2011 11:10
If not already done, would positively identify the exact point of oil leakage.
Thoroughly clean engine and allow to fully dry.
Spray foot powder over edges of head gasket, valve gasket, half moons, tach drive, tach drive, exhaust ports, oil cooler lines.
Basically, cover top end of the clean dry engine with white foot powder.
It will appear almost as "painted" white.
Using a flash light or shop light, start the engine and inspect closely for the first sign of emerging oil, which will darken the powder.
This should confirm exact source of the leak.
And maybe it is indeed the head gasket.
However, the other mentioned areas are more frequent sources of leakage.
And the test is worth the minimal effort involved to possibly avoid unnecessarily replacing a head gasket.
Could also re-torque the head.
When doing so, the engine should be overnight cold.
And do not "first loosen" before torquing.
Good Fortune!
Thoroughly clean engine and allow to fully dry.
Spray foot powder over edges of head gasket, valve gasket, half moons, tach drive, tach drive, exhaust ports, oil cooler lines.
Basically, cover top end of the clean dry engine with white foot powder.
It will appear almost as "painted" white.
Using a flash light or shop light, start the engine and inspect closely for the first sign of emerging oil, which will darken the powder.
This should confirm exact source of the leak.
And maybe it is indeed the head gasket.
However, the other mentioned areas are more frequent sources of leakage.
And the test is worth the minimal effort involved to possibly avoid unnecessarily replacing a head gasket.
Could also re-torque the head.
When doing so, the engine should be overnight cold.
And do not "first loosen" before torquing.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 17 Oct 2011 11:10 by Patton.
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: Head Gasket
17 Oct 2011 11:56
Make sure it's not just the tach drive leaking. That is a very common problem and it's extremely easy to fix with 1 or 2 inexpensive parts. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- rcarver
-
- Offline
- User
-

Registered
- Posts: 62
- Thanks: 0
Re: Head Gasket
17 Oct 2011 14:08
I had a similar problem and I re-torqued my cylinder head nuts, as well as, the front cylinder head bolt down inside the cam chain well. I had my cams out for a valve adjustment anyway.
So far no more oil leaks! The manual says the inner cylinder head bolts (qty:2) only need to be re-torqued during the first service after purchasing the bike new...but I figured there was no way to verify it had been down 30 years ago.
be careful, you don't want to break a bolt or stud and be sure to reference the torque specs in the FSM.
So far no more oil leaks! The manual says the inner cylinder head bolts (qty:2) only need to be re-torqued during the first service after purchasing the bike new...but I figured there was no way to verify it had been down 30 years ago.
be careful, you don't want to break a bolt or stud and be sure to reference the torque specs in the FSM.
1979 KZ650 SR (aka: Stella Blue)
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Head Gasket
17 Oct 2011 15:10
If you find you need to pull it down for gaskets, I would be sure to get an accurate compression test at least, a Leak Down Test even better. A fresh set of valve stem seals minimum when the heads off, good quality ones. You would be adjusting the valve clearances, so make a measurement, and chart it for adjustment.
Besides the leak, does it burn oil?
Besides the leak, does it burn oil?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- Observer
-
Topic Author
- Offline
- User
-

Registered
- Posts: 13
- Thanks: 0
Re: Head Gasket
17 Oct 2011 15:55
Does not burn oil at all.
I changed the cam cover gasket because of oil leaks
now the cam cover no longer leaks, but the head is leaking just
in the spot I mentioned.
I changed the cam cover gasket because of oil leaks
now the cam cover no longer leaks, but the head is leaking just
in the spot I mentioned.
Please Log in or Create an account to join the conversation.
- gwolever
-
- Offline
- User
-

Registered
- Posts: 237
- Thanks: 8
Re: Head Gasket
17 Oct 2011 16:44
After breaking bolts removing my valve cover when I took my engine apart, now I am paranoid that I will snap something in the engine rebuild.
I tightened my head nuts after applying blue thread lock into the nuts. The manual says to use 30 ft.lbs. of torque for head nuts. Will it be the same torque using the blue thread lock or not?
I have my torque wrench set at 30 lbs., but am paranoid that I will hear a snap from broken stud before the click of the wrench tells me to stop.
I tightened my head nuts after applying blue thread lock into the nuts. The manual says to use 30 ft.lbs. of torque for head nuts. Will it be the same torque using the blue thread lock or not?
I have my torque wrench set at 30 lbs., but am paranoid that I will hear a snap from broken stud before the click of the wrench tells me to stop.
1982 KZ1000 CSR
Please Log in or Create an account to join the conversation.
- gwolever
-
- Offline
- User
-

Registered
- Posts: 237
- Thanks: 8
Re: Head Gasket
17 Oct 2011 16:46
Sorry...not trying to hijack thread, just thought this is exactly what I am trying to avoid by not tightening hed nuts enough or even worse...tightening them too much.
1982 KZ1000 CSR
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
