School Me on Gaskets
- PaulyWally
-
Topic Author
- Offline
- User
-

Registered
- Total Bike Newbie
- Posts: 71
- Thanks: 0
School Me on Gaskets
20 Oct 2011 16:50
So I've found a couple trouble areas that I am currently working on. I am replacing the stator cover, and the transmission cover. I forgot to order gaskets with the last order I placed, so I figured I'll just get some gasket material and make my own. It'll be a lot cheaper, and a good skill to learn.
My questions are... is standard cork + rubber gasket material fine for my needs? Is there a particular sealant I should be using? Any recommended resources I should look at before attempting to cut my new gaskets? Am I dumb and just need to purchase the OEM gaskets? Anything I'm not thinking of?
Thanks!
My questions are... is standard cork + rubber gasket material fine for my needs? Is there a particular sealant I should be using? Any recommended resources I should look at before attempting to cut my new gaskets? Am I dumb and just need to purchase the OEM gaskets? Anything I'm not thinking of?
Thanks!
1976 KZ750 Twin
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: School Me on Gaskets
20 Oct 2011 17:05
if u insist on rolling ur own, i would just go to the closest auto parts suply store and buy a small roll of there paper gasket material. it will come rolled up in a box. something like 12" X 12". there are many choises for glue. some like myself like to use a very thin layer of Permatex RTV silicone. others like stuff like Yamabond, and others prefur to go dry.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: School Me on Gaskets
20 Oct 2011 17:11
Both mating surfaces should be free of old gasket and sealing compounds. A piece of sharpened Lexan or Plexiglass will not damage Aluminum engine parts like a metal gasket scraper will, but can still remove old gaskets and sealants.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: School Me on Gaskets
20 Oct 2011 17:59
Pep Boys sells the best paper stuff, 1/32" thick. It has N8904 written on the back as I recall.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- Jeff.Saunders
-
- Offline
- Vendor
-

Vendors
- Posts: 1238
- Thanks: 149
Re: School Me on Gaskets
20 Oct 2011 18:00
Gaskets are a complex material. The material is designed to swell a certain percentage when exposed to different liquids like engine oil. Most gaskets contain a rubber-like binder than will harden when exposed to prolonged heat. Without these properties, the wrong material is likely to weep or worse turn into a major leak. Matching the material to the application is key.
Please Log in or Create an account to join the conversation.
- PaulyWally
-
Topic Author
- Offline
- User
-

Registered
- Total Bike Newbie
- Posts: 71
- Thanks: 0
Re: School Me on Gaskets
20 Oct 2011 18:08Jeff.Saunders wrote: Matching the material to the application is key.
OK. Now for the obligatory question. Which material is best for my application(s)?
1976 KZ750 Twin
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: School Me on Gaskets
20 Oct 2011 18:43
Here’s my view on using sealant; others may disagree. If the idea of putting sealant on a gasket is to prevent a leak, please consider the following. Let’s say you have two metal surfaces, i.e. an engine block and a tensioner housing, and there’s a paper gasket that goes between the two. The purpose of the paper gasket is to prevent oil from leaking between the two metal components. So let’s say you put the gasket in there dry (no sealant at all) and bolt the housing to the block squeezing the gasket between the two. Now consider if you could see that housing/gasket/block joint from inside the engine. You would see metal (the block), the inner edge of the gasket, and metal (the tensioner housing). Now you splash plenty of oil inside that area so the joint is soaked in it. Now looking from inside the engine you see oily metal (block), the oily the inner edge of the gasket, and oily metal (the tensioner housing). If the oil is going to seep between the metal and the gasket will the oil care if it seeps between the block and the gasket or the tensioner housing and the gasket? No, if it is going to leak it can leak on the block side or the housing side of the gasket. So, IF the only way to prevent a leak was to put sealant on the gasket you would need to put it on both sides. Fortunately, the dry paper gasket will not leak on either side, so no sealant is needed. This assumes no one has gouged the metal mating surfaces when trying to remove a gasket that some previous owner has glued on because they didn’t know sealant was not needed. In that case seal may be needed but only on the gouged area. This brings up another point; in the Kawasaki service manual there are a FEW areas where sealant is called for. The best example I can give is two spots on the KZ650 clutch cover gasket. The manual calls for sealant on the two (about 1 inch) spots on the engine side of the clutch cover gasket where the gasket covers the joints between the lower and upper engine castings. This is required because mating surface has a seam at these engine casing joints which the gasket alone may not seal. This may not be obvious to someone doing this job the first time. So my best advice is to always consult the service manual to see if and where sealant is required rather than just gluing the gaskets on and later having to scrape them off. Also, you’ll save money by not needing to replace gaskets as often because the ones put on dry can be more easily reused. The CD recording of this speech is available at the door. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Re: School Me on Gaskets
20 Oct 2011 18:57
ok that was painful, 
buy a gasket from Z1 enterprises and be done with it, only sealant necessary is where the stator wire comes out ....NEXT
buy a gasket from Z1 enterprises and be done with it, only sealant necessary is where the stator wire comes out ....NEXT
Please Log in or Create an account to join the conversation.
- Kraz1
-
- Offline
- User
-

Registered
- Posts: 394
- Thanks: 30
Re: School Me on Gaskets
20 Oct 2011 19:04
Click
> Gasket Thread
> Gasket Thread
Kraz1 wrote: I like the FelPro Rubber-Fiber Sheet #3157. Can be had in Auto-Zone for under $5.00. It's 26 X 10 x 1/32 for sealing oil, water, or gasoline. I've used it for Clutch Cover, and Cam Chain Tensioner Gasket.
Please Log in or Create an account to join the conversation.
- z1kzonly
-
- Offline
- User
-

Registered
- Sustaining Member
- Posts: 2815
- Thanks: 527
Re: School Me on Gaskets
20 Oct 2011 19:29
If ya make gaskets, you need a hole punch set. And hope you don't slice your finger with the new blade on the exacto knife you use. No beer allowed! Only valium, for your patience.
Just my opinion.
By the way what engine?
I made a thermostat gasket for my 68 Nova 6 cylinder in 1977.
Just buy them! What do you need anyway?
Just my opinion.
By the way what engine?
I made a thermostat gasket for my 68 Nova 6 cylinder in 1977.
Just buy them! What do you need anyway?
Livin in "CheektaVegas, NY
Went thru 25 of these in 40 yrs.
I SOLD OUT! THE KAW BARN IS EMPTY.
More room for The Old Girl, Harley 75 FLH Electra Glide,
Old faithful! Points ign. Bendix Orig. carb.
Starts everytime!
Went thru 25 of these in 40 yrs.
I SOLD OUT! THE KAW BARN IS EMPTY.
More room for The Old Girl, Harley 75 FLH Electra Glide,
Old faithful! Points ign. Bendix Orig. carb.
Starts everytime!
Please Log in or Create an account to join the conversation.
- ezrider714
-
- Offline
- User
-

Registered
- Posts: 256
- Thanks: 38
Re: School Me on Gaskets
20 Oct 2011 23:26
Almost all manufactures are heading away from gaskets.
1.) Because they will leak after a certain time period to due the cellular structure of paper/gasket material.
2.)Gaskets are now beads of sealant applied around openings, with the sealant being silicone/rubber compounds tailored for the application, that are impermeable to oil,water,gas or whatever the need. This is usually done robotically,or with x,y,z,machines for simpler processes.
Have installed these systems in many of the major vehicle manufacturer's plant in the last few years.
No reason that this can't be done manually on a bike,the sealants are out there. The only gasket on my bike is the head gasket, heat pressure,and cyclic stresses make this the toughest one, but believe me the gasket manufacturers are hard at work to solve those issues.
Oh and not sure what bike OP has but in the area he mentioned,on my 650 there is no gaskets involved??
1.) Because they will leak after a certain time period to due the cellular structure of paper/gasket material.
2.)Gaskets are now beads of sealant applied around openings, with the sealant being silicone/rubber compounds tailored for the application, that are impermeable to oil,water,gas or whatever the need. This is usually done robotically,or with x,y,z,machines for simpler processes.
Have installed these systems in many of the major vehicle manufacturer's plant in the last few years.
No reason that this can't be done manually on a bike,the sealants are out there. The only gasket on my bike is the head gasket, heat pressure,and cyclic stresses make this the toughest one, but believe me the gasket manufacturers are hard at work to solve those issues.
Oh and not sure what bike OP has but in the area he mentioned,on my 650 there is no gaskets involved??
78 KZ650SR Mine since 79
4-1 Mac Jet Hot coated since mid 80's
Dyna Coils
Saddlebags (I ain't skeered of going nowhere)
4-1 Mac Jet Hot coated since mid 80's
Dyna Coils
Saddlebags (I ain't skeered of going nowhere)
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: School Me on Gaskets
21 Oct 2011 00:59ezrider714 wrote: Almost all manufactures are heading away from gaskets.
1.) Because they will leak after a certain time period to due the cellular structure of paper/gasket material.
2.)Gaskets are now beads of sealant applied around openings, with the sealant being silicone/rubber compounds tailored for the application, that are impermeable to oil,water,gas or whatever the need. This is usually done robotically,or with x,y,z,machines for simpler processes.
Have installed these systems in many of the major vehicle manufacturer's plant in the last few years.
No reason that this can't be done manually on a bike,the sealants are out there. The only gasket on my bike is the head gasket, heat pressure,and cyclic stresses make this the toughest one, but believe me the gasket manufacturers are hard at work to solve those issues.
Oh and not sure what bike OP has but in the area he mentioned,on my 650 there is no gaskets involved??
Regarding your #1 statement that gaskets leak over time, the original gaskets on my bike that have not been replaced for other reasons (for example the generator cover gasket, base gasket, mission cover gasket, oil pan gasket, head gasket, etc.) are nearly 35 years old and still don't leak a drop. So, when you say after a certain period of time could you be more specific. Do you mean 100 years, 200 years, or what?
Regarding your statement that there are no gaskets involved on your bike's generator cover, there should be a gasket there (see diagram for your bike below) but apparently you chose to leave it out. I guess you also left out the base gasket since you claim you have no gaskets other than the head gasket. What does that do to your compression? You can load your bike up with silicone, but I'm glad that's not my bike. Ed
Attachment Gasket.jpg not found
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
