1980 KZ750 E1 Exhaust
- manubati
-
Topic Author
- Offline
- User
-

Registered
- Posts: 12
- Thanks: 0
1980 KZ750 E1 Exhaust
23 Oct 2011 20:42 - 23 Oct 2011 20:43
Hi everyone!
I'm about to buy a KZ750E1 but the exhaust is significantly rusted.
Everything else is in really good to fair condition, and it starts/runs well. 700$. Good deal?
It's a stock h-pipe exhaust, but the joint in the H is rusted through. (circled area)
It's been previously repaired with some sheet metal and clamps but as a result the joints (arrows) are almost fully rusted and are just waiting to fall off. The rest of the exhaust is in rather decent condition, the mufflers are fine. When you start the bike, it doesn't sound that bad at all, but there is definitely air loss and it's a problem at higher revs.
I'm wondering if I can repair this, or if I need to replace the full exhaust system?
Would it be possible to get a shop to construct a replacement bar for the H? If you cut at 1 and 2 and remake that whole piece with exhaust tubing, would that work? Expensive to do?
What are my alternatives?
Thanks!
I'm about to buy a KZ750E1 but the exhaust is significantly rusted.
Everything else is in really good to fair condition, and it starts/runs well. 700$. Good deal?
It's a stock h-pipe exhaust, but the joint in the H is rusted through. (circled area)
It's been previously repaired with some sheet metal and clamps but as a result the joints (arrows) are almost fully rusted and are just waiting to fall off. The rest of the exhaust is in rather decent condition, the mufflers are fine. When you start the bike, it doesn't sound that bad at all, but there is definitely air loss and it's a problem at higher revs.
I'm wondering if I can repair this, or if I need to replace the full exhaust system?
Would it be possible to get a shop to construct a replacement bar for the H? If you cut at 1 and 2 and remake that whole piece with exhaust tubing, would that work? Expensive to do?
What are my alternatives?
Thanks!
Last edit: 23 Oct 2011 20:43 by manubati.
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: 1980 KZ750 E1 Exhaust
23 Oct 2011 22:02
If you dont weld, then take it to a shop.
They could keep things cheap by cutting the section out completely and just capping both sides.
It will change the power band just slightly, not greatly, and makes for a nice different sound.
They could keep things cheap by cutting the section out completely and just capping both sides.
It will change the power band just slightly, not greatly, and makes for a nice different sound.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- manubati
-
Topic Author
- Offline
- User
-

Registered
- Posts: 12
- Thanks: 0
Re: 1980 KZ750 E1 Exhaust
24 Oct 2011 00:00
I can weld, but not that well and I don't have access to one so I'll go to the shop.
By capping both sides, you mean just making 2 x 2-1 pipes and not keeping it as an H?
By capping both sides, you mean just making 2 x 2-1 pipes and not keeping it as an H?
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: 1980 KZ750 E1 Exhaust
24 Oct 2011 00:21
I seem to recall someone on this site once found copper plumbing fittings that were a perfect fit when his cross pipe connections rusted all the way through and had to be removed. He stuck them into the exhaust pipes and connected them with a cross pipe. Invisible under the bike. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 1980 KZ750 E1 Exhaust
24 Oct 2011 13:33Perhaps this thread:650ed wrote: I seem to recall someone on this site once found copper plumbing fittings that were a perfect fit when his cross pipe connections rusted all the way through and had to be removed. He stuck them into the exhaust pipes and connected them with a cross pipe. Invisible under the bike. Ed
www.kzrider.com/forum/advsearch?q=exhaust+copper+cross
Some high temp copper sealant may also be helpful.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- manubati
-
Topic Author
- Offline
- User
-

Registered
- Posts: 12
- Thanks: 0
Re: 1980 KZ750 E1 Exhaust
24 Oct 2011 17:17 - 24 Oct 2011 17:18
Brilliant! That's a cheap an elegant solution, I'll be looking into fixing it that way first. My exhaust is in a little worse condition, but it just might work.
Thanks a lot, I'll take pictures and let you know how it goes!
Thanks a lot, I'll take pictures and let you know how it goes!
Last edit: 24 Oct 2011 17:18 by manubati.
Please Log in or Create an account to join the conversation.
- martin_csr
-
- Offline
- User
-

Registered
- Posts: 7993
- Thanks: 1648
Last edit: 15 Feb 2013 12:01 by martin_csr.
Please Log in or Create an account to join the conversation.
- manubati
-
Topic Author
- Offline
- User
-

Registered
- Posts: 12
- Thanks: 0
Re: 1980 KZ750 E1 Exhaust
30 Oct 2011 03:41
Yes, that's the actual system, although not the one from my bike. I'm taking it out tomorrow morning.
I'll post some pictures.
I'm planning on trying to find some copper plumbing couplings that might fit like in this post ( www.kzrider.com/forum/advsearch?q=exhaust+copper+cross )
My Y is somewhat more rusted, but I don't think it's pierced through. I'm hopping to remove the rust and put some exhaust putty ( to make sure.
I'm not sure of the state of the crossover pipe, there's aluminum sheeting that was tied there to try to seal the holes at both ends.
I'm hoping it's still usable, otherwise would it be possible to replace that with a copper pipe assuming I find some copper couplings like in that post?
Replacing the Y is definitely another possibility if that fails. Thanks for the suggestions!
I'll post some pictures.
I'm planning on trying to find some copper plumbing couplings that might fit like in this post ( www.kzrider.com/forum/advsearch?q=exhaust+copper+cross )
My Y is somewhat more rusted, but I don't think it's pierced through. I'm hopping to remove the rust and put some exhaust putty ( to make sure.
I'm not sure of the state of the crossover pipe, there's aluminum sheeting that was tied there to try to seal the holes at both ends.
I'm hoping it's still usable, otherwise would it be possible to replace that with a copper pipe assuming I find some copper couplings like in that post?
Replacing the Y is definitely another possibility if that fails. Thanks for the suggestions!
Please Log in or Create an account to join the conversation.
- clutch
-
- Offline
- User
-

Registered
- I wish I had a tad more patience to do it better!
- Posts: 1051
- Thanks: 13
Re: 1980 KZ750 E1 Exhaust
30 Oct 2011 03:56
I'm not sure what your budget is, but you could also go with an aftermarket exhaust as well. I replaced the stock exhaust on my E3 when it fell apart removing it to drop the oil pan. After installing my Vance and Hines, I had fun chopping up the rest of the stock exhaust so it would fit in my trash can! LOL! :woohoo:
Southern Maryland, USA
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
