tool list for doing a clutch replacement.
- metrorollah
-
Topic Author
- Offline
- User
-

Registered
- Posts: 21
- Thanks: 0
tool list for doing a clutch replacement.
27 Oct 2011 03:59
hey kz riders. I left my 1979 KZ650SR at my folks place in Pennsylvania after I rode it across the country, and I'm going there this weekend to replace the clutch. I've got all the parts waiting for me there, but I need to pack a tool box to go. I've done this job before but it was about 15 years ago. I want to make sure I have everything.
1) impact driver and bits (hammer)
2) 8-14mm combination wrenches
3) 10-19mm sockets, ratchets, extensions
4) allen key drivers
5) screw driver assortment
6) pliers
it should just be taking off the footpeg, kickstarter, brake lever, clutch cover, four bolts holding the clutch basket together. put new clutches in, installation is reverse of removal with a new gasket.
right?
am I forgetting anything besides capital letters?
1) impact driver and bits (hammer)
2) 8-14mm combination wrenches
3) 10-19mm sockets, ratchets, extensions
4) allen key drivers
5) screw driver assortment
6) pliers
it should just be taking off the footpeg, kickstarter, brake lever, clutch cover, four bolts holding the clutch basket together. put new clutches in, installation is reverse of removal with a new gasket.
right?
am I forgetting anything besides capital letters?
Please Log in or Create an account to join the conversation.
- clutch
-
- Offline
- User
-

Registered
- I wish I had a tad more patience to do it better!
- Posts: 1051
- Thanks: 13
Re: tool list for doing a clutch replacement.
27 Oct 2011 05:17
7) rtv sealant
new springs (if needed)
Southern Maryland, USA
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
The following user(s) said Thank You: metrorollah
Please Log in or Create an account to join the conversation.
- clutch
-
- Offline
- User
-

Registered
- I wish I had a tad more patience to do it better!
- Posts: 1051
- Thanks: 13
Re: tool list for doing a clutch replacement.
27 Oct 2011 05:24
You will probably want to soak the new plates in clean oil (whatever type you run in your bike) before installing them.
Southern Maryland, USA
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
The following user(s) said Thank You: metrorollah
Please Log in or Create an account to join the conversation.
- Link14
-
- Offline
- User
-

Registered
- Posts: 575
- Thanks: 6
Re: tool list for doing a clutch replacement.
27 Oct 2011 10:24
+1 on clutches advice. I'd also take along a torque wrench for putting stuff back together. Also the FSM if you've got it.
Please Log in or Create an account to join the conversation.
- RonKZ650
-
- Offline
- User
-

Registered
- Posts: 3719
- Thanks: 252
Re: tool list for doing a clutch replacement.
27 Oct 2011 10:46
Your list is all you need I can think of. If you clean the gasket area there is not any need of sealer at all. I always figure the plates will be in oil for the rest of eternity so could never figure what good it does to pre-oil them? Lots of guys do though, and doesn't hurt, but no advantage to doing so in my opinion.
321,000 miles on KZ's that I can remember. Not going to see any more.
Please Log in or Create an account to join the conversation.
- kzryderyahoo
-
- Offline
- User
-

Registered
- Posts: 13
- Thanks: 1
Re: tool list for doing a clutch replacement.
27 Oct 2011 11:58
Just be sure to install the steel plates back the same orientation the came out.
1976 KZ 900
The following user(s) said Thank You: metrorollah
Please Log in or Create an account to join the conversation.
- P21
-
- Offline
- User
-

Registered
- Posts: 471
- Thanks: 34
Re: tool list for doing a clutch replacement.
27 Oct 2011 12:02kzryderyahoo wrote: Just be sure to install the steel plates back the same orientation the came out.
+1 here
Kawasaki KZ 1000 Police (2002) P21
Please Log in or Create an account to join the conversation.
- clutch
-
- Offline
- User
-

Registered
- I wish I had a tad more patience to do it better!
- Posts: 1051
- Thanks: 13
Re: tool list for doing a clutch replacement.
27 Oct 2011 13:53 - 27 Oct 2011 13:56
Definitely on the FSM and torque wrench! Make sure you don't tighten the bolts that hold the springs too much. I've broken many of them in the past being too aggressive with them. Snug is better than torqued if you don't have specs for those little guys.
Southern Maryland, USA
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
Last edit: 27 Oct 2011 13:56 by clutch.
The following user(s) said Thank You: metrorollah
Please Log in or Create an account to join the conversation.
- metrorollah
-
Topic Author
- Offline
- User
-

Registered
- Posts: 21
- Thanks: 0
Re: tool list for doing a clutch replacement.
27 Oct 2011 15:09 - 27 Oct 2011 15:11
great tips you guys! I would have definitely left the torque wrench at home. also the orientation of the plates, totally forgot that. new springs are in the parts list for sure. half the time the disks have plenty of meat and its the springs that are bad.
Thanks!
Thanks!
Last edit: 27 Oct 2011 15:11 by metrorollah.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
