Starter noise

  • baldy110
  • baldy110's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 2272
  • Thanks: 512

Starter noise

27 Oct 2011 13:29
#485625
I finally got around putting oil into my ELR build after rebuilding the engine. GPz1100 engine. I removed the sparkplugs, disconnected the ignitor and pushed the start button to get the oil moving. It turns the engine over but the starter is making a nasty grinding noise. Kinda sounds like the starter clutch right before it stops working. But it spins the engine over fine just sounds terrible. I did not replace the starter clutch rollers or springs in the rebuild since the engine had low miles. I don't know if it made this sound before because I never heard this engine run. I bought it years ago and it came off a wrecked GPz. Is this normal for the 1000 series engines?

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Starter noise

27 Oct 2011 14:46
#485632
What type & grade of oil being used?

Best Oils To Use In Your Bike (Just My Opinion)

Engine oil : The commercial grade oils are clearly superior to the mass market oils. For the best protection in your bike or car, use Shell Rotella Synthetic, available at Wal-Mart in blue containers . For the best petroleum oil you can buy, get Shell Rotella T, Mobil Delvac 1300, or Chevron Delo 400, available at any auto parts store. On the back of most oil cans is a circular stamp with the certification.

Avoid oils that say "energy conserving" in the bottom half of the donut. These oils contain friction modifier additives that could cause clutch slipping over time. The EPA mandated certain gas mileage, so the auto makers turned to the oil manufacturers who came up with friction modifiers of the oil to meet these new standards. All XXw-20 and XXw-30 oils are energy conserving, and should not be used in your motorcycle. Don't buy any oil additives like STP or Slick-50. Here's several listings on all about oil justifying these conclusions.

The Recommended Synthetic Oils :

Shell Rotella Synthetic
5w-40 Delvac 1 Synthetic
5w-40 Mobil-1 SUV/Truck Synthetic
5w-40 AMSOil AMF Synthetic (pricey, but it’s your money)
10w-40 Golden Spectro Synthetic
10w-50 Motul 5100 Synthetic
10w-40 Mobil-1 Synthetic
15w-50 Mobil-1 MX4T Synthetic

The best synthetics are: (in no particular order)

Shell Rotella-T Synthetic 5w-40 (blue container is synthetic, not white which is dino), gallon at Wal-Mart.
Mobil Delvac-1 5w-40 (grey container is synthetic, not black which is dino), gallon at Petro stations, gallon at Farm and Fleet.
Mobil-1 SUV 5w-40, qt anywhere.
AMSOil AMF 10w-40 synthetic motorcycle oil. (again, pricey)
Golden Spectro Supreme, (no price).
Motul 5100 Ester, (no price).

Mobil-1 automotive oils all contain small amounts of moly - about 100 to 200 ppm. This can cause clutch slippage in some motorcycles. I've only heard of this being a problem in Honda Shadows.


The Recommended Petroleum Oils

Chevron Delo 400 15w-40
Delvac 1300 15w-40
Shell Rotella 15w-40

The best petroleum oils are: (in no particular order)

Chevron Delo 400 15w-40 (blue container) gallon at any auto parts store, gallons at Costco.

Mobil Delvac 1300 15w-40 (black container) gallon at any auto parts store, gallons at Sam's Club.

Shell Rotella-T 15w-40 (white container) gallon at Wal-Mart or any auto parts store, gallons at Sam's Club.

Castrol 15w-40 (Green container) gallon at Wal-Mart or any auto parts store, gallons at Sam’s club.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Starter noise

27 Oct 2011 14:51
#485633
If you're using oil rated for motorcycle use, and the starter clutch noise is getting worse, probably this needs to be done:

Over Running Starter Clutch Repair On the Older, Bigger 4’S

1. When preparing to repair the starter over running clutch have a few items on hand:

A. New alternator cover gasket.
B. New springs (3).
C. New spring caps (3).
D. New rollers (3).

2. If possible, put the motorcycle on the center stand and tilt to the right to reduce the oil volume in the alternator cover.

3. Place an oil catch pan under the left side of the engine to collect what small amount of oil that will escape when the alternator cover is removed.

4. Remove the foot shifter lever, left foot peg assembly and the sprocket cover.

5. Some Kawasaki’s have socket head cap screws(Allen type) and others may have fasteners with a Phillips type. If the latter is there, a # 3 bit seems to work the best for removal.

6. Remove the alternator cover and take care with the three wires coming from the alternator stator. These are the voltage supply wires for the motorcycle. Rest the cover on some newspaper or rags to prevent damage.

7. The magnetic Rotor or flywheel will probably require a removal bolt or puller. NOTE, SOME ENGINES HAVE LEFT HAND THREADS ON THE ROTOR!!


8. The over running clutch is bolted to the back of the rotor with three Allen head fasteners.

9. Separate the rotor from the over running clutch and inspect for damage in the springs, rollers, and spring caps. Replace any worn parts.

10. Re-assemble in reverse order taking care when re-installing the Alternator cover not to pinch any wires. If the cover will not re-install without force, check before any damage occurs.

11.One caution. These tend to get the skips and have difficulty with the one way clutch on the starter holding once they have been taken apart if the old parts are reused. They may not look that worn, but as a matter of course I would replace the entire part # 13193-1006 and part # 92026-112.

12.Also, if you presently have a follow-on rattle or growl once the bike has started take a good look at the starter motor gear, Part # 21167-002, and the pin on which it rotates. That gear and pin tends to wear the center bearing surface after only thirty or so years and then cocks under load and puts the starter clutch assembly in a bind causing it to skip or rattle. One problem looks like the other.

13.Use assembly lube when putting the starter gear back together with the pin.

14. Read this procedure from Red Line Cycle:
redlinecycle.com/Starter%20Clutch%20Tech.html
(It may show a blank page, but information is there).
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum