Piston rings
- busted knuckle
-
Topic Author
- Offline
- User
-

Registered
- Posts: 28
- Thanks: 1
Piston rings
29 Oct 2011 18:49
I just started a complete rebuild on a 1979 kz750b4 kawasaki. my piston rings need to be replaced and I was wondering if it is worth replacing the ones I have or if i should bore it out while im going through all the trouble?
1979 kz 750 b4
Please Log in or Create an account to join the conversation.
- kzryderyahoo
-
- Offline
- User
-

Registered
- Posts: 13
- Thanks: 1
Re: Piston rings
29 Oct 2011 20:09
How is the compression? Leak down test? Are you doing cam chain and valves too? If you are then I'd suggest a professional hone. But if this is a quick n cheap job then forget the boring of cyl.
1976 KZ 900
Please Log in or Create an account to join the conversation.
- busted knuckle
-
Topic Author
- Offline
- User
-

Registered
- Posts: 28
- Thanks: 1
Re: Piston rings
30 Oct 2011 00:00
I am restoring the bike for my dad who owned it before me. However I am not a mechanic. I don't know about a leak down test. A friend of mine said the compression was off because it would start fine cold, but warm it would give me a lot of trouble. The cylinder block is currently stuck on. I've been told this might be from the piston rings fusing to the block. I want to do the best job that I can, but don't know where to start on boring, but the cam chain and valves will be replaced.
1979 kz 750 b4
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Piston rings
30 Oct 2011 09:22busted knuckle wrote: I am restoring the bike for my dad who owned it before me. However I am not a mechanic. I don't know about a leak down test. A friend of mine said the compression was off because it would start fine cold, but warm it would give me a lot of trouble. The cylinder block is currently stuck on. I've been told this might be from the piston rings fusing to the block. I want to do the best job that I can, but don't know where to start on boring, but the cam chain and valves will be replaced.
"A friend of mine said the compression was off because it would start fine cold, but warm it would give me a lot of trouble. "
this has nothing to do with compresion .if u have poor compresion, it would be hard to start. if it starts fine the compresion may be fine.
since u didnt do a compresion test, u will need to measure the pistons and the bore and then determin if they are out of spec.
start by getting yourself a good manual and read through it so u know what u are into hear.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: Piston rings
30 Oct 2011 12:22
The block is stuck due to corrosion around the front studs that secure the block to the case. Spray some penetrating oil on the exposed studs in the front, then let it set for awhile.
KD9JUR
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Piston rings
30 Oct 2011 15:30 - 30 Oct 2011 15:33busted knuckle wrote: I just started a complete rebuild on a 1979 kz750b4 kawasaki. my piston rings need to be replaced and I was wondering if it is worth replacing the ones I have or if i should bore it out while im going through all the trouble?
BORE IT.
You are very lucky because piston and ring sets are readily available and CHEAP for the 750 twins.
You can get them in all sizes from stock to 1.0mm over. I got mine from cyclewareables.com. I think they were $36/set.
www.cyclewareables.com/pages/vintage_pis...age_piston_rings.htm
1979 KZ-750 Twin
Last edit: 30 Oct 2011 15:33 by bountyhunter.
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: Piston rings
31 Oct 2011 08:41 - 31 Oct 2011 08:42busted knuckle wrote: I am restoring the bike for my dad who owned it before me. However I am not a mechanic. I don't know about a leak down test. A friend of mine said the compression was off because it would start fine cold, but warm it would give me a lot of trouble. The cylinder block is currently stuck on. I've been told this might be from the piston rings fusing to the block. I want to do the best job that I can, but don't know where to start on boring, but the cam chain and valves will be replaced.
Step 1: Get a new friend. Preferably someone who is not an idiot.
Step 2: Use your brain; not your friend's (remember, he's an idiot). If the engine would start fine how can the piston rings be fused to the cylinders? The engine would not even turn over much less run if that was the case.
Step 3: Diagnose the problem before disassembling the engine. Ooops. too late.
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Last edit: 31 Oct 2011 08:42 by 650ed.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Piston rings
31 Oct 2011 09:39 - 31 Oct 2011 09:40I just started a complete rebuild on a 1979 kz750b4 kawasaki. my piston rings need to be replaced and I was wondering if it is worth replacing the ones I have or if i should bore it out while im going through all the trouble?
I am restoring the bike for my dad who owned it before me. However I am not a mechanic. I don't know about a leak down test. A friend of mine said the compression was off because it would start fine cold, but warm it would give me a lot of trouble. The cylinder block is currently stuck on. I've been told this might be from the piston rings fusing to the block. I want to do the best job that I can, but don't know where to start on boring, but the cam chain and valves will be replaced.
Whether or not to re-bore often depends on condition of the cylinders and extent of wear. When in doubt, a bore-gauge may be used to measure the diameter and roundness of the cylinders at various positions inside. These measurements are made with the engine block removed and sitting on the work bench. It's probably best to have a competent machinest perform the measurements. Sometimes high mileage alone is sufficient reason to re-bore up to the next size larger piston and rings, but a leakdown test before disassembly should reveal exactly how much compression is escaping down around the pistons and rings and into the crankcase.
In some cases, using new rings of the same size may work okay, after simple honing -- not boring -- inside the cylinders, to remove the wall glaze, which allows the new rings to seat.
An engine starting cold, but giving trouble when warm, may result from insufficient valve clearances. Because the minimal clearance allows compression when cold, but the minimal clearance then vanishes as the engine warms, whereby the valves no longer fully close, permitting compression to escape through the unclosed valve seat.
In this case, where rings may have rusted against the cylinders, would consider boring to the next over-size, with replacement of pistons and rings, and a valve job, including new valve stem seals.
The existing cam chain may be all right if it hasn't stretched enough to exceed factory specs.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 31 Oct 2011 09:40 by Patton.
Please Log in or Create an account to join the conversation.
- busted knuckle
-
Topic Author
- Offline
- User
-

Registered
- Posts: 28
- Thanks: 1
Re: Piston rings
31 Oct 2011 19:59
I finally have the cylinder block off! I've been told I can clean engine parts with an engine degreaser. Is it safe to clean the whole block with this? I will be taking the block and pistons to a shop to get them checked out and their opinion of the wear
1979 kz 750 b4
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Piston rings
31 Oct 2011 20:38
After cleaning, get a clean rag and apply some clean oil to the inside of the cylinder bores to reduce the chance of rust forming. A light oil film is about all you need.
Get some assembly lube for the cam bearings and other parts lubricated with engine oil
as they will be dry when you start the engine after reassembly.
Get some assembly lube for the cam bearings and other parts lubricated with engine oil
as they will be dry when you start the engine after reassembly.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- rich67
-
- Offline
- User
-

Registered
- Posts: 210
- Thanks: 61
Re: Piston rings
31 Oct 2011 20:40
purple degreaser has sodium hydroxide very corrosive to aluminum . I used simple green 50/50 mix works well .
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
