KZ 750 won't start
- ghostrider43945
-
Topic Author
- Offline
- User
-

Registered
- Posts: 2
- Thanks: 0
KZ 750 won't start
31 Oct 2011 13:43
77 kz750, i press start button, starter will engauge but bike wont start. any body have any ideas?
Please Log in or Create an account to join the conversation.
- P21
-
- Offline
- User
-

Registered
- Posts: 471
- Thanks: 34
Re: KZ 750 won't start
31 Oct 2011 13:57
you got kill switch turned on?
Kawasaki KZ 1000 Police (2002) P21
Please Log in or Create an account to join the conversation.
- ghostrider43945
-
Topic Author
- Offline
- User
-

Registered
- Posts: 2
- Thanks: 0
Re: KZ 750 won't start
31 Oct 2011 14:02
it's on run, i pulled the plugs out pressed start button to see if i get a spark but no spark, the points have been changed, replaced ciol and battery
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: KZ 750 won't start
31 Oct 2011 15:21
Check the input voltage to the ignition coils, it should be battery voltage. If no voltage, get out the meter and start tracing back until voltage is found.Look inside the headlight housing for loose or corroded wiring too.
Many of these older bikes ae suffering soldered joints that are crumbling in the left and right handlebar switch pods.
Hand Soldering
Rosin flux(the paste type)works the best for me when soldering. Also get an acid brush and some 91% rubbing alcohol to clean the soldered joint(s). Use it to flush away any rosin residue as it's a non conductor.
A couple(2)of toothpicks to apply the rosin flux, a damp sponge to wipe the soldering irons tip occasionally, and rosin core solder is about all you'll need for this repair.
If the soldering iron is new, it probably needs "Tinning", to do so. follow these steps:
1.Have on hand either a damp, clean sponge or rag.
2.Plug in the soldering iron and let it get hot(maybe 2-3 minutes).
3.Unroll a few inches of the solder and then using a paper towel damp with rubbing alcohol, wipe away the fingerprint oils you left when handling the solder.
4.Apply a small amount of solder to the tip of the now hot soldering iron.
5.Using the damp sponge or rag, wipe away the excess solder, leaving a thin amount.
6.The iron is now "Tinned" and ready for use.
7.Periodically wipe the soldering iron tip & apply solder to keep the working surface in good shape, keeping in mind to not have too much solder on the tip.
8.For a good soldered joint, remove if possible all of the old solder, keeping in mind that the switch may be made of low temperature plastic that will not take much heat to warp and be ruined.
9.A "Solder Sucker" or "Solder Wick" is the best way to remove old solder from joints.
Many of these older bikes ae suffering soldered joints that are crumbling in the left and right handlebar switch pods.
Hand Soldering
Rosin flux(the paste type)works the best for me when soldering. Also get an acid brush and some 91% rubbing alcohol to clean the soldered joint(s). Use it to flush away any rosin residue as it's a non conductor.
A couple(2)of toothpicks to apply the rosin flux, a damp sponge to wipe the soldering irons tip occasionally, and rosin core solder is about all you'll need for this repair.
If the soldering iron is new, it probably needs "Tinning", to do so. follow these steps:
1.Have on hand either a damp, clean sponge or rag.
2.Plug in the soldering iron and let it get hot(maybe 2-3 minutes).
3.Unroll a few inches of the solder and then using a paper towel damp with rubbing alcohol, wipe away the fingerprint oils you left when handling the solder.
4.Apply a small amount of solder to the tip of the now hot soldering iron.
5.Using the damp sponge or rag, wipe away the excess solder, leaving a thin amount.
6.The iron is now "Tinned" and ready for use.
7.Periodically wipe the soldering iron tip & apply solder to keep the working surface in good shape, keeping in mind to not have too much solder on the tip.
8.For a good soldered joint, remove if possible all of the old solder, keeping in mind that the switch may be made of low temperature plastic that will not take much heat to warp and be ruined.
9.A "Solder Sucker" or "Solder Wick" is the best way to remove old solder from joints.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
The following user(s) said Thank You: ghostrider43945
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: KZ 750 won't start
31 Oct 2011 15:22 - 31 Oct 2011 15:24ghostrider43945 wrote: it's on run, i pulled the plugs out pressed start button to see if i get a spark but no spark, the points have been changed, replaced coil and battery
Attachment points-condensertext.JPG not found
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 31 Oct 2011 15:24 by Patton.
The following user(s) said Thank You: ghostrider43945
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
