starting issue
- k0ba1t
-
Topic Author
- Offline
- User
-

Registered
- Posts: 31
- Thanks: 0
starting issue
02 Nov 2011 03:16
Ok so I've been able to start my bike, but only for a few seconds using starting fluid. Fuel is getting to the carbs because there was some in the bowls, so what could be the problem within the carbs? The float needle and seats? Need some imput here. On a side note, she sounds niiiice!
1978 kz650c matte black. Current project.
Please Log in or Create an account to join the conversation.
- stonemaster
-
- Offline
- User
-

Registered
- Sorry I wasnt paying attention
- Posts: 24
- Thanks: 0
Re: starting issue
02 Nov 2011 08:13 - 02 Nov 2011 08:14
jets are clogged would be my first guess, clean all components , and while ur at it check float levels, wouldnt hurt to check the inside of ur tank for debris, get a fuel filter if u dont have one, if u dont have one get a manual
jus ridin my Rickshaw baby, among other things
Last edit: 02 Nov 2011 08:14 by stonemaster.
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: starting issue
02 Nov 2011 12:20
Use choke. Increase idle speed. Check mixture/air screws for proper setting.
Make sure no air leaks and proper filtration is fitted snug.
Fully charged battery, helps engine turn over quicker.
Shouldnt be any need to use throttle, but if necessary, use only a small 1/16 turn crack of throttle to assist.
Good luck.
Make sure no air leaks and proper filtration is fitted snug.
Fully charged battery, helps engine turn over quicker.
Shouldnt be any need to use throttle, but if necessary, use only a small 1/16 turn crack of throttle to assist.
Good luck.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: starting issue
02 Nov 2011 13:27k0ba1t wrote: Ok so I've been able to start my bike, but only for a few seconds using starting fluid. Fuel is getting to the carbs because there was some in the bowls, so what could be the problem within the carbs? The float needle and seats? Need some imput here. On a side note, she sounds niiiice!
Glad it sounds "Nice"
Now getting fuel to the carbs, open the petcock to "Prime" so the fuel will freely flow. Then open the Carb Float Bowl drain screws, with a catch container under the black tubes/ hoses. Watch the fuel flow, with the drains open it should run out of those tubes/ hoses. On all carbs. Then tighten the drains back up, put a piece of clear tubing onto the drain fitting, and reopen the drain. Placing the tube up against the side of the carb body, look at how far the fuel rises. It should be just below the gasket surface of the bowl to body. If good on all carbs, tighten the drains and retry starting the bike.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- k0ba1t
-
Topic Author
- Offline
- User
-

Registered
- Posts: 31
- Thanks: 0
Re: starting issue
03 Nov 2011 05:45stonemaster wrote: jets are clogged would be my first guess, clean all components , anzld while ur at it check float levels, wouldnt hurt to check the inside of ur tank for debris, get a fuel filter if u dont have one, if u dont have one get a manual
Jets arnt clogged, I cleaned everything, I have a manual, I have a fuel filter. It sounds like there is some debris in the tank, but it is not interupting flow. May just be the chain for the gascap actually.
I had the choke to full and if I didn't use the throttle she wouldn't start. I was opening to full throttle, spraying some starting fluid in, then kicking it while giving it some throttle. Oh i should note my starter clutch is bad lol. Thought it was the starter itself, but after replacing that, a nice grinding and whirring sound insued lol.
When i am.able to get back to the bike in a week or two, ill try some of that fuel dranage stuff. Where should I have the idle screw set at? Also, is there a good place to educate me on these mikuni carbs and tuning them? Is the manual good? This is the second bike I have ever worked on and I still have some stuff to learn.
I think my float needles and seats need to be replaced though. I replaced the needle/seat in a carb that was overflowing, and the older ones are not near as springy. They even stick sometimes. Could that be the problem in itself?
Sorry for the short novel lol.
1978 kz650c matte black. Current project.
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: starting issue
03 Nov 2011 09:01
Sometimes sticking? The Float valve needle and seat? No you can't have that happening. First they may stick shut, keeping gas from entering the carb, then next they'll stick and cause flooding. If you replaced one needle and seat Assy on one carb, you should go back in there, and replace the others. Then set your fuel level. The one you replaced, did you check the fuel level?
If you go into "Filebase", it's at the top right corner of the KZR tool bar. Go to Non Specific models, there is a lot of great carb info there that members have posted. Check it out.
If you go into "Filebase", it's at the top right corner of the KZR tool bar. Go to Non Specific models, there is a lot of great carb info there that members have posted. Check it out.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Please Log in or Create an account to join the conversation.
- k0ba1t
-
Topic Author
- Offline
- User
-

Registered
- Posts: 31
- Thanks: 0
Re: starting issue
04 Nov 2011 23:35
No i did not check the fuel level. I don't k.ow how anyways lol. Is that with the clear piece of tubing? But yeah i already planned on replacing them. Is there any way to get just the needle/seat? Would z1 have them?
K0
K0
1978 kz650c matte black. Current project.
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: starting issue
05 Nov 2011 00:24
I don't see where at Z1 they list the float needle and seat separately from rebuild kits, but I would just either email or call them. They'll help you out.
yes the fuel level is checked, and very important, with a clear piece of tubing. Attach to the drain on the float bowl, and run up along the side of the carb. It should be just below the bowl to carb body gasket surface, within 3mm.
yes the fuel level is checked, and very important, with a clear piece of tubing. Attach to the drain on the float bowl, and run up along the side of the carb. It should be just below the bowl to carb body gasket surface, within 3mm.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- k0ba1t
-
Topic Author
- Offline
- User
-

Registered
- Posts: 31
- Thanks: 0
Re: starting issue
06 Nov 2011 03:45
Well I will have to try that. It will be a few weeks before i get back to my bike however. Hopefully another day of work will get her running!
On another note, all the jets are free and clear and do not look damaged, so are the float needles and seats the only thing I should replace?
On another note, all the jets are free and clear and do not look damaged, so are the float needles and seats the only thing I should replace?
1978 kz650c matte black. Current project.
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: starting issue
06 Nov 2011 12:38Motor Head wrote: I don't see where at Z1 they list the float needle and seat separately from rebuild kits, but I would just either email or call them. They'll help you out.
yes the fuel level is checked, and very important, with a clear piece of tubing. Attach to the drain on the float bowl, and run up along the side of the carb. It should be just below the bowl to carb body gasket surface, within 3mm.
The float valve assembly, part #16030-1001, is still available from Kawasaki. It includes the needle and seat. Ronayers.com lists the price at $24.67 each. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
