79 Mark II flywheel magnet adhesive/epoxy
- 1978z1r
-
Topic Author
- Offline
- User
-

Registered
- Posts: 5
- Thanks: 0
79 Mark II flywheel magnet adhesive/epoxy
08 Nov 2011 04:50
I searched to the best of my ability to find information regarding the orange non-metal connective material on the magnets of my flywheel from a 79 Mark II. I have changed up to a 79 Mark II crank welded and balanced for my Turbo Z1R 1396. When I changed cranks, I had to change to the Mark II dynamo. I will post a picture tommorrow, but little portions of the orange epoxy on the outer edge of the flywheel have come loose.
What is the general opinion and experience with this subject. I saw several posts where the epoxy was mostly off and it wasn't mentioned in the posts. Can it be repaired? These flywheels are hard to find and poor in quality when you can find them.
Thanks in advance
What is the general opinion and experience with this subject. I saw several posts where the epoxy was mostly off and it wasn't mentioned in the posts. Can it be repaired? These flywheels are hard to find and poor in quality when you can find them.
Thanks in advance
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: 79 Mark II flywheel magnet adhesive/epoxy
08 Nov 2011 10:12 - 08 Nov 2011 10:18
A Google search turns up a lot of info, including places that sell the epoxies.
This is only 1; www.emsadhesives.com/Selector_Guide/perm...magnet_assembly.html
If you re attach 1 or more magnets, the clearance/ air-gap to the Stator should be checked. It's probably OK, but but this is one of the areas that could cause a problem. Also the balance, could be effected slightly. For a stock motor I doubt it would be an issue.
Then there is Why did the Magnet come loose, was the Rotor Pulled on from the outer diameter? Of when the correct tool was inserted, was it just vibrations from an Impact wrench or hammer? To get the stuck Rotor off the Taper? Is the Rotor true or Tweaked? Who knows on these older bikes, unless you've owned it from new.
When I did the Starter clutch on my 82, I saw one Magnet that looks re-attached with most likely JB Weld. Seems to work just fine, but the RPM my bike sees is generally under 5K, with a few redline pulls. Nothing like what yours would see.
This is only 1; www.emsadhesives.com/Selector_Guide/perm...magnet_assembly.html
If you re attach 1 or more magnets, the clearance/ air-gap to the Stator should be checked. It's probably OK, but but this is one of the areas that could cause a problem. Also the balance, could be effected slightly. For a stock motor I doubt it would be an issue.
Then there is Why did the Magnet come loose, was the Rotor Pulled on from the outer diameter? Of when the correct tool was inserted, was it just vibrations from an Impact wrench or hammer? To get the stuck Rotor off the Taper? Is the Rotor true or Tweaked? Who knows on these older bikes, unless you've owned it from new.
When I did the Starter clutch on my 82, I saw one Magnet that looks re-attached with most likely JB Weld. Seems to work just fine, but the RPM my bike sees is generally under 5K, with a few redline pulls. Nothing like what yours would see.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 08 Nov 2011 10:18 by Motor Head.
Please Log in or Create an account to join the conversation.
- z1kzonly
-
- Offline
- User
-

Registered
- Sustaining Member
- Posts: 2815
- Thanks: 527
Re: 79 Mark II flywheel magnet adhesive/epoxy
08 Nov 2011 13:01
Red "Glyptol" non conductive paint. Electricians and chromers use it. If it is still available.
Livin in "CheektaVegas, NY
Went thru 25 of these in 40 yrs.
I SOLD OUT! THE KAW BARN IS EMPTY.
More room for The Old Girl, Harley 75 FLH Electra Glide,
Old faithful! Points ign. Bendix Orig. carb.
Starts everytime!
Went thru 25 of these in 40 yrs.
I SOLD OUT! THE KAW BARN IS EMPTY.
More room for The Old Girl, Harley 75 FLH Electra Glide,
Old faithful! Points ign. Bendix Orig. carb.
Starts everytime!
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
