Camshaft bores

  • mrbrettbaker
  • mrbrettbaker's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 3
  • Thanks: 0

Camshaft bores

08 Nov 2011 08:33 - 08 Nov 2011 08:40
#487567

Attachment quad1.JPG not found


Hello all. I attempted a search this morning but came up dry. I built a quad around an 82 J motor and am in the process of replacing the head.Someone put larger cam cap studs in and skewed the caps a bit. I am going to align bore/hone them but have not found a spec for the bore without the bearing shells. If anyone has these specs I'll name a valve shim after them! ;)
Last edit: 08 Nov 2011 08:40 by mrbrettbaker.

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Camshaft bores

08 Nov 2011 09:52
#487571
I've got a pdf copy of the service manual in my signature. But looking through it for the Cam Bearing info, well they have the spec for the bearing to Cam journal clearance, and the cam journal, but I don't see the bore. Are they all out of alignment? Or can one still be measured? Someone with a spare head might get a measurement of theirs, accurate? Working from the shell thickness, and the other two specs, you should be able to work out the crush of the shells. Won't be much, as when they sit in the head, the edges of the bearing is nearly flush. The small bent stake tabs, when in those grooves do a lot to hold them. Did you get some New of different good shells? New is expensive through Kawasaki. I wonder if some of the Automotive Shells are the same Dimension, and the bearing supplier would have the Bore spec?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • mrbrettbaker
  • mrbrettbaker's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 3
  • Thanks: 0

Re: Camshaft bores

08 Nov 2011 10:26
#487577
Thanks for the quick reply AND the link! I have a junk head I am stripping parts from and can get the measurements, just hoped a manual had it listed. My good bore gauge doesnt go that small and this is too critical for calipers or hole gauges. I only have one cam thats caps were altered on. I machined a delrin bushing that the shank of an expandable reamer fit in and whose outside diameter fit the other cam bore. This will allow me to ream and keep alignment. I will hone the last thou or so with a barrel hone. I will also probably pin the shells for this cam, should the crush be less than adequate. It's a J head and getting hard to find, and oh well, I'm cheap!

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Camshaft bores

08 Nov 2011 10:48
#487583
Is the reamer long enough to do all 4, at the same time? You don't want to be taking material off of the bottom/ Head side of the bearing bore, on just one journal. Your cam will get a bend in it and wobble. Taking the bearing in that bore to an Egg shape. Increasing clearance, loosing oil pressure, flexing the camshaft, etc.
You might well see about an Bearing Shell that is a larger outside Dia, by a few thousand, maybe .010" and having it Bored through all 4. Or possibly just honed with the proper tools.
Is this head not the common, J series that fits the 1000-1100, 81-96? Or is it a specific GPZ head? With larger ports/ valves?
The standard head is easy to find on Feebay or members here.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • mrbrettbaker
  • mrbrettbaker's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 3
  • Thanks: 0

Re: Camshaft bores

08 Nov 2011 11:23
#487585
It's long enough to do two and a tight bushings keeps it true to the other two. I worked in an automotive machine shop when I was a youngin and know what to look out for.what you have to do is just like align boring a crank bore. You grind a small amount off the flats of the caps and then the bore is shaped like an eyeball. This way you take equal amounts top and bottom and all bores stay aligned. In this case, because I am taking so little, I slip a piece of .001" stainless shim between reamer and head half of bore, and only the aluminum cuts

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum