Nervous - Looking For Reassurance...

  • PaulyWally
  • PaulyWally's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Total Bike Newbie
  • Posts: 71
  • Thanks: 0

Nervous - Looking For Reassurance...

09 Nov 2011 17:15
#487792
...or someone to tell me I royally screwed up. :)

I just finished replacing the transmission cover and gasket on my bike. There was no torque specified for these specific screws, so I used the chart for "all other bolts and nuts" in the service manual.

6mm screws with a 1mm thread pitch = 4.5 ~ 6.5 ft-lbs.

On each screw, I put some blue Locktite on 1/2~3/4 of a single thread (one of the first threads of the screw). I set my 1/4" torque wrench to 60 in-lbs and I went in circles around the cover, gradually tightening each screw several times, until they all clicked.

Being that this is my first official experience with a torque wrench, I soon discovered that 60 in-lbs (5 ft-lbs) really isn't that much torque. Since I'm naturally nervous and high-strung, I went to 65 in-lbs and tightened them all again. I still wasn't satisfied, so I went to 70 in-lbs. But that's where I stopped since I was almost at 6 ft-lbs.

I'm totally worried that this isn't tight enough and the cover is going to leak like a sieve when I start it.

What say you?
1976 KZ750 Twin

Please Log in or Create an account to join the conversation.

  • Mcdroid
  • Mcdroid's Avatar
  • Offline
  • Sustaining Member
  • Sustaining Member
    Registered
  • Gone Kwackers
  • Posts: 6909
  • Thanks: 530

Re: Nervous - Looking For Reassurance...

09 Nov 2011 17:22
#487793
I say you'll be fine...just as long as the cover and the cases were very clean of any goo and old gasket material before you threw in a new gasket. :)
Michael
Victoria, Texas

1982 GPz750
1977 KZ1000A
1978 KZ1000A
1982 GPz1100
1975 Z2A

Please Log in or Create an account to join the conversation.

  • PaulyWally
  • PaulyWally's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Total Bike Newbie
  • Posts: 71
  • Thanks: 0

Re: Nervous - Looking For Reassurance...

09 Nov 2011 17:29
#487795
Mcdroid wrote: I say you'll be fine...just as long as the cover and the cases were very clean of any goo and old gasket material before you threw in a new gasket. :)

Yeah. I took a lot of time on that part of it.
1976 KZ750 Twin

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: Nervous - Looking For Reassurance...

09 Nov 2011 18:27
#487799
u must be very carful not to overtighten them. they are easy to strip.
:sick:
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Nervous - Looking For Reassurance...

09 Nov 2011 18:57 - 09 Nov 2011 18:58
#487802
That's plenty tight, and you didn't need the lock-tite (although don't fret over it, it won't hurt anything). You do need to learn to trust your torque wrench; it is your friend. If you had left it set at 60 in. lb. it would have been fine. These are small screws going into soft aluminum so do not use the following procedure:

A. Set torque wrench to specified torque value.
B. Tighten bolt until wrench indicates correct torque value has been achieved.
C. Decide to tighten bolt another one half turn.
D. Feel threads strip out of engine case.
E. Loosen bolt one half turn and pray it doesn't fall out at 100 mph.... :woohoo:
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Last edit: 09 Nov 2011 18:58 by 650ed.

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Nervous - Looking For Reassurance...

09 Nov 2011 20:08
#487808
PaulyWally wrote: ...or someone to tell me I royally screwed up. :)
I just finished replacing the transmission cover and gasket on my bike. There was no torque specified for these specific screws, so I used the chart for "all other bolts and nuts" in the service manual.
6mm screws with a 1mm thread pitch = 4.5 ~ 6.5 ft-lbs.
On each screw, I put some blue Locktite on 1/2~3/4 of a single thread (one of the first threads of the screw). I set my 1/4" torque wrench to 60 in-lbs and I went in circles around the cover, gradually tightening each screw several times, until they all clicked.
Being that this is my first official experience with a torque wrench, I soon discovered that 60 in-lbs (5 ft-lbs) really isn't that much torque. Since I'm naturally nervous and high-strung, I went to 65 in-lbs and tightened them all again. I still wasn't satisfied, so I went to 70 in-lbs. But that's where I stopped since I was almost at 6 ft-lbs.
I'm totally worried that this isn't tight enough and the cover is going to leak like a sieve when I start it.
What say you?

For fledgling torque wrench neophytes, especially naturally nervous and high-strung fledging torch wrench neophytes, forget those el cheapo shade tree brands, and get an original genuine "Black Forest" brand torque wrench. These wrenches have no equal, and are scientifically calibrated to the precise German Virgin Standard, which in most applications specify the Guttentite setting.

It's high time to move beyond 650ed's time-honored redneck technique of "Twist until it strips, then back off 1/2 turn."

Hope this helps. :lol:

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Nervous - Looking For Reassurance...

10 Nov 2011 15:54 - 10 Nov 2011 15:55
#487913
Make sure the torque wrench is appropriate. Some people will use a 100 f-pound wrench set at 5 ft-lb to tighten small bolts and rip them out. If you are torquing for 60 inch pounds, it's best to have a wrench that has full scale setting of maybe 200 I-P max so the set point will be accurate. Anytime you use a tool set at a very low value (compared to full scale) accuracy is pretty iffy.

Harbor Freight makes a decent 200 I-P small torque wrench for the small screws and bolts.
1979 KZ-750 Twin
Last edit: 10 Nov 2011 15:55 by bountyhunter.

Please Log in or Create an account to join the conversation.

  • Mcdroid
  • Mcdroid's Avatar
  • Offline
  • Sustaining Member
  • Sustaining Member
    Registered
  • Gone Kwackers
  • Posts: 6909
  • Thanks: 530

Re: Nervous - Looking For Reassurance...

10 Nov 2011 16:47
#487925
bountyhunter wrote: Make sure the torque wrench is appropriate. Some people will use a 100 f-pound wrench set at 5 ft-lb to tighten small bolts and rip them out. If you are torquing for 60 inch pounds, it's best to have a wrench that has full scale setting of maybe 200 I-P max so the set point will be accurate. Anytime you use a tool set at a very low value (compared to full scale) accuracy is pretty iffy.

Harbor Freight makes a decent 200 I-P small torque wrench for the small screws and bolts.

X2 on what he said...I own two torque wrenches...one in ft/lbs and the second in in/lbs...both from Harbor Freight. Have had both calibrated and they are pretty much spot on.
Michael
Victoria, Texas

1982 GPz750
1977 KZ1000A
1978 KZ1000A
1982 GPz1100
1975 Z2A

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum