Front End Cures KZ1000E?

  • fxdl2051
  • fxdl2051's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 96
  • Thanks: 2

Front End Cures KZ1000E?

13 Nov 2011 07:32
#488278
Ok guys, so I replaced the fork seals and put Progressive springs in the '79 Shaftie hoping to cure my pogo stick ride. But the front end still gives a very jolting ride. I love the motor, but these forks not so much. I've read the fork design suffers from stickchin but was hoping the new springs would have addressed that. Any suggestions for smoothing out the ride?
Thanks all,Ken

Please Log in or Create an account to join the conversation.

  • bls5050
  • bls5050's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 34
  • Thanks: 2

Re: Front End Cures KZ1000E?

13 Nov 2011 10:29
#488283
I've got an '80 with pretty much the same issue. My major problem is the excessive nosediving under heavy braking. While you are probably never going to get the silky-smooth ride of say a new Beemer, there are some things you can do to improve the ride. One is to go to a heavier weight oil: if you run the standard 10-weight, go to 15. If you don't like the 15-weight, try 20-weight. Another thing that works is to evenly increase the amount of oil in the tubes. This gives you less air at the top to compress. This smoothed my bike right out.

Another thing you could try is cutting small spacers out of PVC pipe of the right diameter that fit on top of the springs. Start with small spacers and gradually increase the size. This allows you to alter the amount of preload on the springs. Just make sure that the plug at the top of the fork threads back in smoothly!

I hope some of this helps. I'm currently running 15-weight oil, 30mm higher than the FSM states, with 12mm spacers(I don't remember what size PVC pipe. Just something we had at work that was the right diameter and wall thickness). This combination vastly improved my front-end handling, But now I'm wondering what a new pair of Works Performance springs feel like.
1980 KZ1000st
The following user(s) said Thank You: fxdl2051

Please Log in or Create an account to join the conversation.

  • etbike3135
  • etbike3135's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 379
  • Thanks: 50

Re: Front End Cures KZ1000E?

13 Nov 2011 11:18
#488290
Get rid of the progressive springs, worst junk on the market.
1973 Kawasaki Z1
18 years in dragbikes
The following user(s) said Thank You: fxdl2051

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Front End Cures KZ1000E?

13 Nov 2011 11:40 - 13 Nov 2011 11:44
#488293
Springs have more to do with ride height and rebound than they do with damping. Damping is primarily managed by the fork cylinders and fork oil. What fork oil brand/weight are you using and how did you measure how much to put in? Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Last edit: 13 Nov 2011 11:44 by 650ed.
The following user(s) said Thank You: fxdl2051

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: Front End Cures KZ1000E?

13 Nov 2011 12:10
#488298
u may want to look into some Racetech gold valves. they will alter the damping. call them direct and ask what they can do for u.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
The following user(s) said Thank You: fxdl2051

Please Log in or Create an account to join the conversation.

  • loudhvx
  • loudhvx's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 10863
  • Thanks: 1622

Re: Front End Cures KZ1000E?

13 Nov 2011 12:59 - 13 Nov 2011 13:36
#488307
Low rate (soft) springs will cause pogo sticking and nosediving. You can get the same ride height with soft springs or hard springs. Preload is what affects ride height.

On these old bikes, we generally only have rebound damping, and you control that by the weight of the oil (as Bls5050 said). If you want compression damping or adjustable damping without changing oil, you can install racetech valves, as Mark said.

Definitely need to make sure you have the correct level of oil as Ed mentioned. You can raise it slightly to get a little more progressive air pressure, but this will increase sticktion. Usually the manual will describe using a dipstick to set the level properly. I use a big, plastic syringe available at most pharmacies, and connect a small hose if you need to suck any oil out. (And, of course, you have to plunge the forks a few times to get the air out to get the oil level settled.)

It sounds like your forks springs are just too soft. The easiest way to fix it is to get new springs, like etbike said.

The hard way, but cheapest way, is to cut the springs down and add more preload spacer. Cutting them down increses the spring rate, and you add spacers to compensate for the length. Maybe try it with your old springs first. There is a method to it if you are interested.

Did you replace the upper bushing, if there is one? That will help the seal last longer and reduce some of the fork play.

When you put the springs in, were you sure to put enough preload spacer so that the springs never come un-loaded? If they unload, that gives a little more of a jolting ride. But usually a jolting ride is from bottoming out, you can prevent that with more preload if you have enough travel available, (as Bls5050 explained). Put a zip tie around the fork just above the slider dust boot and ride around. After a few hard bumps, see if the zip tie indicates that the forks bottomed out.

Also, there are small springs around the damper tube. They are called top-out springs. Were they in there and installed correctly? Without them, you'll get jolt after a big bump as the forks extend on rebound.
Last edit: 13 Nov 2011 13:36 by loudhvx.

Please Log in or Create an account to join the conversation.

  • Nebr_Rex
  • Nebr_Rex's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1889
  • Thanks: 295

Re: Front End Cures KZ1000E?

13 Nov 2011 21:35
#488355
mark1122 wrote: u may want to look into some Racetech gold valves. they will alter the damping. call them direct and ask what they can do for u.

Made my own out of aluminum.
Turned down to fit between the spring and rod.
With 4 holes drilled with about 1/4 of the total area of the hole on the dampner rod.
I use 5W Bel Ray and Progressive springs achieving improved low speed(small bumps)
and high speed(big bumps)handling.
I also recommend a good aftermarket shock.
I hope this helped somebody out.
2002 ZRX1200R
81 GPz1100
79 KZ1000st daily ride
79 KZ1000mk2 prodject
78 KZ650sr
78 KZ650b
81 KZ750e
80 KZ750ltd
77 KZ400/440 cafe project
76 KZ400/440 Fuel Injected

www.dotheton.com/index.php?threads/dr-je...air-of-kz400s.39120/


.

Please Log in or Create an account to join the conversation.

  • TomW
  • TomW's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep the blue side up.
  • Posts: 502
  • Thanks: 52

Re: Front End Cures KZ1000E?

14 Nov 2011 19:26 - 14 Nov 2011 19:28
#488482
Nebr_Rex wrote:
mark1122 wrote: u may want to look into some Racetech gold valves. they will alter the damping. call them direct and ask what they can do for u.

Made my own out of aluminum.
Turned down to fit between the spring and rod.
With 4 holes drilled with about 1/4 of the total area of the hole on the dampner rod.
I use 5W Bel Ray and Progressive springs achieving improved low speed(small bumps)
and high speed(big bumps)handling.
I also recommend a good aftermarket shock.
I hope this helped somebody out.

Are your shop made valves adjustable like the Racetechs? I am considering Gold valves for my 78 LTD. My pocket book finds the home brew option attractive. Can you supply a dimensioned drawing or sketch of your creations?
'78 KZ1000B2 LTD stock + Vetter Fairing & luggage
'91 ZG1200B5 Voyager XII, stock
Last edit: 14 Nov 2011 19:28 by TomW.

Please Log in or Create an account to join the conversation.

  • fxdl2051
  • fxdl2051's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 96
  • Thanks: 2

Re: Front End Cures KZ1000E?

15 Nov 2011 05:58
#488554
Just wondering what your body weight is, don't know how much of a factor that's going to be, but with those forward sitting handlebars, I'm guessing it counts for something? Tell me about those replacement springs you're thinking about, have you any feedback from others that have run them on this model? I've got to say, that I'm disappointed in the Progressive's, I had them years ago in another bike and they seemed to work well. Thanks for the feedback.
ss^, Ken

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum