HArd starting issue
- jon_570
-
Topic Author
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
Re: HArd starting issue
04 Dec 2011 18:01
yes the slides were installed in that fashion.
1982 Kawasaki Spectre 750 N1
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: HArd starting issue
04 Dec 2011 18:08
So slides are OK.
Have you set the Fuel level in the Bowls with a clear piece of tubing hooked to the drain, and routed up along the side of the carb body with the Petcock on Prime? It should be right about the height of the gasket surface, you'll have to check your service manual for the exact height on those. But fuel Level is very important, if low it will be lean through out the carb circuits. It sounds like you have a Lean issue going on. Double check with some Carb Spray that there are No Vacuum leaks. The Idle will raise up if you have any.
Have you set the Fuel level in the Bowls with a clear piece of tubing hooked to the drain, and routed up along the side of the carb body with the Petcock on Prime? It should be right about the height of the gasket surface, you'll have to check your service manual for the exact height on those. But fuel Level is very important, if low it will be lean through out the carb circuits. It sounds like you have a Lean issue going on. Double check with some Carb Spray that there are No Vacuum leaks. The Idle will raise up if you have any.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- jon_570
-
Topic Author
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
Re: HArd starting issue
04 Dec 2011 18:19
i have sprayed carb cleaner around boots and idle did not raise. i also have done the fuel level. manual says about 4mm below gasket surface. i bench tested them. should i do it with the carbs on the bike? that big airbox makes everything a pain.
1982 Kawasaki Spectre 750 N1
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: HArd starting issue
04 Dec 2011 18:26 - 04 Dec 2011 18:32
On the bench with the carbs level is the correct way. I'm just trying to see if i can find something for you with out going into those carbs again. It sure sounds like a carb problem. If it'll start on Choke, and then Idle with it off, but not take throttle, then to me that sounds like a Blocked circuit. But I know you have been in there a few times. Do you use compressed air when blowing things clean? Sometimes it can take a small wire to poke the crude out. Just how dirty etc, were these carbs? Lots of white powder/ corrosion? Just a small amount of varnish?
So if you run the bike with just a small amount off choke, does it then Accelerate?
It may be a good check to see the fuel level while on the bike, at least on the two outside,1-4 carbs. They are easy to get to and you can verify the fuel is staying at the preset level, so as to rule out the bowl level dropping.
So if you run the bike with just a small amount off choke, does it then Accelerate?
It may be a good check to see the fuel level while on the bike, at least on the two outside,1-4 carbs. They are easy to get to and you can verify the fuel is staying at the preset level, so as to rule out the bowl level dropping.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 04 Dec 2011 18:32 by Motor Head.
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: HArd starting issue
04 Dec 2011 18:35 - 04 Dec 2011 19:32
I just went back and read this:
"I have a 1982 Kawi KZ750 Spectre. with 82xx miles on the odometer. Its been sitting for a while. so i did some small things. i had to clean out the tank. installed new fuel lines and inline fuel filter. changed oil and filter. new spark plugs. also put in new main jets. i think are the ones.'
Now which jet did you change? Was it the same # as you removed? In the Diagram above, page 1, whats the # in the Diagram, and the # on the Jet?
There are two reasons for asking, first it very well may be the issue, Jet change.
Also not all jets are the same. Both Mikuni and Keihin jets can have the same thread, but different flow #'s. So a 120 from each manufacturer is not the same jet size. Then there is Dyno-Jet, another # equation.
Maybe its the Jets you changed?
"I have a 1982 Kawi KZ750 Spectre. with 82xx miles on the odometer. Its been sitting for a while. so i did some small things. i had to clean out the tank. installed new fuel lines and inline fuel filter. changed oil and filter. new spark plugs. also put in new main jets. i think are the ones.'
Now which jet did you change? Was it the same # as you removed? In the Diagram above, page 1, whats the # in the Diagram, and the # on the Jet?
There are two reasons for asking, first it very well may be the issue, Jet change.
Also not all jets are the same. Both Mikuni and Keihin jets can have the same thread, but different flow #'s. So a 120 from each manufacturer is not the same jet size. Then there is Dyno-Jet, another # equation.
Maybe its the Jets you changed?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 04 Dec 2011 19:32 by Motor Head.
Please Log in or Create an account to join the conversation.
- jon_570
-
Topic Author
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
Re: HArd starting issue
04 Dec 2011 23:19
i replaced the float needles. because the rubber on the bottom was falling off. and i changed the idle air screw. i ordered these from bike bandit and it stated it was a rebuild kit spec for te spectre 750 82
1982 Kawasaki Spectre 750 N1
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: HArd starting issue
05 Dec 2011 10:11
So no Jet Sizes were changed then? As you posted that you changed the Main Jet earlier.
Just the Mixture screw and the float needle, with some gaskets/ o-ring is the Economy K7L kit I see Bike Bandit sells. That kit has no Jets in it. Otherwise the other Regular K&L kit has the Jets in the Kit, and should be compared to the OEM jets when changing them.
Just the Mixture screw and the float needle, with some gaskets/ o-ring is the Economy K7L kit I see Bike Bandit sells. That kit has no Jets in it. Otherwise the other Regular K&L kit has the Jets in the Kit, and should be compared to the OEM jets when changing them.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- jon_570
-
Topic Author
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
Re: HArd starting issue
06 Dec 2011 00:14
no jets were changed yea it was the economy kit.
all actualy jets are stock. maybee i should try cleaning them again and using the air compressor again.
all actualy jets are stock. maybee i should try cleaning them again and using the air compressor again.
1982 Kawasaki Spectre 750 N1
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: HArd starting issue
06 Dec 2011 11:03jon_570 wrote: no jets were changed yea it was the economy kit.
all actualy jets are stock. maybee i should try cleaning them again and using the air compressor again.
Well that can't hurt, pay close attention to all the small little holes for the Low speed, and transition circuits.
Just wondering, have you done a compression test, I don't see that posted? If it has at least 100psi on all 4 it should run, but you would like at least 120 or better, up to about 160, even #'s between them + or - 10psi.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- jon_570
-
Topic Author
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
Re: HArd starting issue
06 Dec 2011 23:12
didnt do a compressions check but i know its fairly good. because turning it with a wrench is hard to do and you can feel the compression strokes. plus it starts fairly well and idles good. just doesnt rev up. Im thinking its either cylinder 1 or 3 carb because those 2 occassionally backfire.
1982 Kawasaki Spectre 750 N1
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: HArd starting issue
07 Dec 2011 10:53
Unless you've already done this, I would pull those Manifolds/ Carb holders to have a look. They maybe getting cracked, separated, or just not sealing at the head. Easy to do while the Carbs are off.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- jon_570
-
Topic Author
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
Re: HArd starting issue
07 Dec 2011 16:02
I checked them and theyre fine I also applied some high temp gasket sealer to the and reinsta.led and let sit for 24 hours
1982 Kawasaki Spectre 750 N1
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
