HArd starting issue
- jon_570
-
Topic Author
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
HArd starting issue
17 Nov 2011 21:15
I have a 1982 Kawi KZ750 Spectre. with 82xx miles on the odometer. Its been sitting for a while. so i did some small things. i had to clean out the tank. installed new fuel lines and inline fuel filter. changed oil and filter. new spark plugs. also put in new main jets. i think are the ones. and cleaned the carbs with carb cleaner.. then an air compressor. then boiled them in water and lemon juice. have read this works wonders and it worked pretty goood. i think the carbs are fairly clean and the best they will be. Now when i crank the bike over i hazve the choke on. and it sputters a little bit and sounds like it wants to start but sometimes back fires through the carbs. I dont kknow whazt else i could try. i know the valve clearances could be causing it but with only 8k miles i dont know why it would wear so much. Also the float levels could be out of whack but i dont have a manual yet. cant order onee till tomorrow and wont be here till monday. bad thing is i have the bike in the garage and i need to have it out monday because other stuff needs t go in the garage. so im gathering ideas on what i can do to this thing tomorrow to try and get it running. it has compression. i dont have a tester but when cranking by hand you can feel each piston go on its power stroke and it gets hard to turn. im about out of ideas to try on the bike. If i were to not have filters at all on this bike and not filter box would this cause a problem? i have the stock box which im going to use im just waiting on new rubber boots so it all works good. but would this cause a vacuum problem and not let it start?? Any ideas are greatly appreciated.
1982 Kawasaki Spectre 750 N1
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: HArd starting issue
17 Nov 2011 22:10
Some checks to do:
1.The sparkplug caps contain a resistor(5000 ohms)that can go bad after a while. It's designed to reduce the electrical noise on radio's and TV.s. www.z1enterprises.com sells new ones.
2.Try new sparkplugs correctly gapped,(I believe 0.028" to 0.031" is the range).
3.Do this check of the pickup coils:
Ohm Checking Pickup(Pulsing) Coils
The pickup coils on the Kawasaki’s with the factory supplied electronic ignition can sometimes fail or become intermittent due to heat and vibration.
1.Trace back from where the pick up coils are mounted,(under a right side CD sized cover) locate and disconnect a small 4 pin connector. Using a multi-meter set on OHMS and range of 2K, check between the BLUE and BLACK wires(#1 and #4 sparkplug wires) for between 360- 540 OHMS.
2.For #2 and #3 sparkplugs the wire colors will be YELLOW and RED, again 360-540 OHMS. The 550’s,650’s & 750’s may be backwards to the Z1’s,Kz900’s,Kz1000’s & Kz1100’s.
3.If the pickup coils are suspect of failing due to heat, they can be stressed using a hair dryer without the need of the engine running.
4.A replacement set of pickup coils might be obtained from a dealer who serviced the police Kawasaki’s.
5. If replacement pickup coils are not available, your next choice would be to order a Dyna “S” electronic ignition system from www.z1enterprises.com It replaces the IC igniter with a smaller module located where the mechanical ignition advancer was mounted.
6. Checking with Kawasaki.com website has determined that the Pick up(pulsing) coils are available . The pulsing coil # is 59026-1133 and replaces the older # 1002, 1012 which were used from the MKII motors until the 2005 P24.
7.Check the small 4 pin connector that the pickup coils connect to for corrosion/loose pins too.
1.The sparkplug caps contain a resistor(5000 ohms)that can go bad after a while. It's designed to reduce the electrical noise on radio's and TV.s. www.z1enterprises.com sells new ones.
2.Try new sparkplugs correctly gapped,(I believe 0.028" to 0.031" is the range).
3.Do this check of the pickup coils:
Ohm Checking Pickup(Pulsing) Coils
The pickup coils on the Kawasaki’s with the factory supplied electronic ignition can sometimes fail or become intermittent due to heat and vibration.
1.Trace back from where the pick up coils are mounted,(under a right side CD sized cover) locate and disconnect a small 4 pin connector. Using a multi-meter set on OHMS and range of 2K, check between the BLUE and BLACK wires(#1 and #4 sparkplug wires) for between 360- 540 OHMS.
2.For #2 and #3 sparkplugs the wire colors will be YELLOW and RED, again 360-540 OHMS. The 550’s,650’s & 750’s may be backwards to the Z1’s,Kz900’s,Kz1000’s & Kz1100’s.
3.If the pickup coils are suspect of failing due to heat, they can be stressed using a hair dryer without the need of the engine running.
4.A replacement set of pickup coils might be obtained from a dealer who serviced the police Kawasaki’s.
5. If replacement pickup coils are not available, your next choice would be to order a Dyna “S” electronic ignition system from www.z1enterprises.com It replaces the IC igniter with a smaller module located where the mechanical ignition advancer was mounted.
6. Checking with Kawasaki.com website has determined that the Pick up(pulsing) coils are available . The pulsing coil # is 59026-1133 and replaces the older # 1002, 1012 which were used from the MKII motors until the 2005 P24.
7.Check the small 4 pin connector that the pickup coils connect to for corrosion/loose pins too.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
The following user(s) said Thank You: jon_570
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: HArd starting issue
17 Nov 2011 22:49
"If i were to not have filters at all on this bike and not filter box would this cause a problem? i have the stock box which im going to use im just waiting on new rubber boots so it all works good. but would this cause a vacuum problem and not let it start?? Any ideas are greatly appreciated."
They won't want to run with out the Airfilter/ Airbox connected at the rear of the carb. So if you have nothing on the Intake side of your Carb, then it would be quite lean. Maybe a shot of Gas, or Ether would get it going. but you need the connection to the box.
They won't want to run with out the Airfilter/ Airbox connected at the rear of the carb. So if you have nothing on the Intake side of your Carb, then it would be quite lean. Maybe a shot of Gas, or Ether would get it going. but you need the connection to the box.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- lemo32
-
- Offline
- User
-

Registered
- The Price of Cool aint cheap
- Posts: 316
- Thanks: 2
Re: HArd starting issue
17 Nov 2011 22:51
Sounds like your flying blind, diagnostics is a system of elimination, guess work just leads to more guessing, or buying parts you Don't need, take the time and go through each system.
1979 kz 1000 06 katana 750
Please Log in or Create an account to join the conversation.
- KZJOE900
-
- Offline
- Administrator
-

Super Users
- Posts: 1984
- Thanks: 455
Re: HArd starting issue
17 Nov 2011 22:53
I ideally you should do what MFolks has suggested. But if time is against you, just spray some starting fluid (replaces your carburetor function) in each bore of the carburetors. Then crank it while giving it at least 1/3 throttle. Should fire up if it has good spark. Who knows, it may even stay running (assuming your are getting fuel to the carbs). But as for adjustment of idle mixture, you should have your filter installed. It will be running lean with out them.
Current project 76 KZ900 (This was a Vetter model)
76 KZ900
81 XJ550H SECA (Current Project)
82 XJ550R SECA
Past:
86 FJ1200
74 Z1900
72 CB450
76 KZ900
81 XJ550H SECA (Current Project)
82 XJ550R SECA
Past:
86 FJ1200
74 Z1900
72 CB450
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: HArd starting issue
19 Nov 2011 12:28jon_570 wrote: ... 1982 Kawi KZ750 Spectre. with 82xx miles on the odometer. Its been sitting for a while... think the carbs are fairly clean and the best they will be... sputters a little bit and sounds like it wants to start but sometimes back fires through the carbs. I dont kknow whazt else i could try. i know the valve clearances could be causing it but with only 8k miles i dont know why it would wear so much....
Would check valve clearances.
And also assure that the timing advancer is properly functioning.
Which is best done with a strobe type timing light to watch the advancer timing marks quickly move back and forth as engine rpm is varied by blipping the throttle.
Would at the least put a few drops of oil on the advancer pivot points (accessible through the timing inspection window), as the moving arms on the advancer might be sticking.
Hoping the advancer doesn't look like this:
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- jon_570
-
Topic Author
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
Re: HArd starting issue
19 Nov 2011 19:59
Thanks for all the help guys. Well today i got it started. It will idle now for about 30 seconds then it sounds like it loads up with fuel and shuts off. also when i give it throttle it just kinda stalls in place and doesnt rev up. Any ideas. The previous owner must have replaced sparkplug wires or coils and mixed the wires up. straightened them out and it fired right up with the choke. not i need to tune it to get it running right but might need some help
1982 Kawasaki Spectre 750 N1
Please Log in or Create an account to join the conversation.
- jon_570
-
Topic Author
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
Re: HArd starting issue
19 Nov 2011 20:10
and actually with the choke on if i remember correctly it would rev up if i gave it throttle. if i remember corrrectly. ill have to check tomorrow when i go out
1982 Kawasaki Spectre 750 N1
Please Log in or Create an account to join the conversation.
- jon_570
-
Topic Author
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
Re: HArd starting issue
19 Nov 2011 20:48
dont mean to keep replying or could it be that because i dont have filters on yet it is running real lean and not letting it rev or stay idling
1982 Kawasaki Spectre 750 N1
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: HArd starting issue
19 Nov 2011 21:53
Don't bother trying to make it run right until the airbox (with a filter in it) is hooked up, otherwise you will get very frustrated. These bikes don't run well with the back of the carbs open to the atmosphere. As you suggested, they run too lean that way. Once the filter is on you should see an improvement. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- jon_570
-
Topic Author
- Offline
- User
-

Registered
- Posts: 56
- Thanks: 0
Re: HArd starting issue
03 Dec 2011 23:37
actually mine looks like the first one. i have the cover off and i took everything apart and my advancer looks like the first picture. rusted. the spring still have movement and the arms still move freely with tension from the spring of course. and the piece that has the holes drilled in it that comes to a point, is usually lined up a little to the right of the indent on the silver screw. if i move it a little bit too the right, and start the bike, the bike will sound more like it wants to rev up and stay running. I cleaned every single passage and every single jet in the carb. a few were still clogged. i went through everything. the floats are adjusted at 4mm. which is what the manual states. and i have the idle screw, because i replaced them, the spring,washer, and rubber o-ring with new ones, i have them set at 2 turns out as stated in the manual. and the bike will start when cold with choke on and will stay running with the choke off. once i give it gas though it justfalls on its face. i dont know what else i could do.
1982 Kawasaki Spectre 750 N1
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: HArd starting issue
04 Dec 2011 00:29
1982 Kawi KZ750 Spectre
sometimes back fires through the carbs
only 8k miles
will idle now for about 30 seconds then it sounds like it loads up with fuel and shuts off. also when i give it throttle it just kinda stalls in place and doesn't rev up.
with the choke on if i remember correctly it would rev up if i gave it throttle
I cleaned every single passage and every single jet in the carb. a few were still clogged.
bike will start when cold with choke on and will stay running with the choke off. once i give it gas though it just falls on its face. i don't know what else i could do.
Depending on the particular carb design, perhaps the pilot circuit is still partially clogged and/or the pilot jet plug is loose or missing.
Of particular concern would be (1) the small passageway and (2) the plug, as shown in the following diagrams.
Good Fortune!
sometimes back fires through the carbs
only 8k miles
will idle now for about 30 seconds then it sounds like it loads up with fuel and shuts off. also when i give it throttle it just kinda stalls in place and doesn't rev up.
with the choke on if i remember correctly it would rev up if i gave it throttle
I cleaned every single passage and every single jet in the carb. a few were still clogged.
bike will start when cold with choke on and will stay running with the choke off. once i give it gas though it just falls on its face. i don't know what else i could do.
Depending on the particular carb design, perhaps the pilot circuit is still partially clogged and/or the pilot jet plug is loose or missing.
Of particular concern would be (1) the small passageway and (2) the plug, as shown in the following diagrams.
Attachment cvcarbpilotjetplugoring.jpg not found
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
The following user(s) said Thank You: jon_570
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
