APE CAM CHAIN IDLER ADAPTER

  • JEFFG1
  • JEFFG1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 341
  • Thanks: 16

APE CAM CHAIN IDLER ADAPTER

04 Dec 2011 14:48 - 04 Dec 2011 14:55
#491477

Attachment Picture002.jpg not found



Attachment Picture001.jpg not found



Attachment ccia.jpg not found





i am about to order ape adapter for the head in the pic but i dont understand how it will fit in the guide? if you look at my head it has the stock mount bolt holes in it i have been looking at the adapter it dont look like it it milled to fit inside or outside of the guide. the jig that they sell looks like you would drille on both sides of the stock mount but you will still have the casting in the way. do you order these for this head or is it one fits all. do you grind the casting after you drill the holes???
1976 KZ 900 PRO STREET 1977 kz1000 dragbike project
Last edit: 04 Dec 2011 14:55 by JEFFG1.

Please Log in or Create an account to join the conversation.

  • etbike3135
  • etbike3135's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 379
  • Thanks: 50

Re: APE CAM CHAIN IDLER ADAPTER

04 Dec 2011 14:52
#491479
Most of the time the center of the head gets milled. This is not too much of diy project. Even if you have the jig you need a drill or extension about 12" to drill the holes.
1973 Kawasaki Z1
18 years in dragbikes

Please Log in or Create an account to join the conversation.

  • JEFFG1
  • JEFFG1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 341
  • Thanks: 16

Re: APE CAM CHAIN IDLER ADAPTER

04 Dec 2011 15:06
#491480
the jig comes with a 12" bit. so you do have to grind.to the inside or the out?? you must have to grind before installing jig?
1976 KZ 900 PRO STREET 1977 kz1000 dragbike project

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: APE CAM CHAIN IDLER ADAPTER

04 Dec 2011 15:32
#491486
I've never done one, but looking at the info on KZone, it says to simply bolt the jig onto the head and drill. Maybe it is made to go around the casting of the valve cover screws? Maybe they need to be made flat across the casting bosses? Don't know but either a call to APE, or a PM to APE JAY will get the info you need. Can't find a Tech article on site there with the info. But it has to be easy enough either way. Don't you have to adjust the Compression ratio for the J series head?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: APE CAM CHAIN IDLER ADAPTER

04 Dec 2011 15:58
#491492
Pretty sure the jig was made so you could DIY the swap.

I would call APE, Jeff. They will have the answer for you.

Please Log in or Create an account to join the conversation.

  • JEFFG1
  • JEFFG1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 341
  • Thanks: 16

Re: APE CAM CHAIN IDLER ADAPTER

04 Dec 2011 16:26
#491499
( motor head ) the pistons that are going in this motor are wisco 1230 with very high compression
1976 KZ 900 PRO STREET 1977 kz1000 dragbike project

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: APE CAM CHAIN IDLER ADAPTER

04 Dec 2011 16:40
#491502
JEFFG1 wrote: ( motor head ) the pistons that are going in this motor are wiseco 1230 with very high compression
Figured you would be doing something along those lines.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: APE CAM CHAIN IDLER ADAPTER

04 Dec 2011 17:07
#491515
i have never had 1 of those in my hand. maybe it is recessed inside so that it fits around the bolts casting hump . just call ape.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • etbike3135
  • etbike3135's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 379
  • Thanks: 50

Re: APE CAM CHAIN IDLER ADAPTER

04 Dec 2011 17:47 - 04 Dec 2011 17:48
#491530
Every head I have ever seen with a conversion tower has been milled. It even cuts into the casting beyond the 2 big humps. You have to find the center and mill both sides. Milling also gives a nice square bottom for the tower to set on that you would never get with a hand grinder. You could do this easily on a bridgeport mill.
Use the grinder on the valve cover for clearance there.
1973 Kawasaki Z1
18 years in dragbikes
Last edit: 04 Dec 2011 17:48 by etbike3135.

Please Log in or Create an account to join the conversation.

  • APE Jay
  • APE Jay's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: APE CAM CHAIN IDLER ADAPTER

04 Dec 2011 23:04
#491575
The conversion comes with instructions. You put the head in a mill and cut each side the same amount so that the adaptor sits in the middle and not off to one side.

The area where the threaded holes are, is .500" thick, so the instructions tell you to mill it .510" deep. This will assure that the adaptor sits below the gasket surface.

When it is machined correctly, there will be small ridges that the adaptors sits on and then the bolts hold it in place.

Then the valve cover needs to be machined. The adaptor is .900 wide at this point, so we machine the valve cover out .910". again in the center. The valve cover is what holds the pin that the sprocket rides on, in place, so it should not be more than .910 or it will allow the pin to move back and forth too much.

Please do not try and do this with some kind of a grinder. If you damage the head, you will not be able to save it.

We get $65.00 to do the entire installation labor. Many shops have our jig and can also do it.

Please Log in or Create an account to join the conversation.

  • JEFFG1
  • JEFFG1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 341
  • Thanks: 16

Re: APE CAM CHAIN IDLER ADAPTER

05 Dec 2011 18:16
#491730
boy that is alot more than i ever dreamed of. it sounded like it was a user freindly deal! shit i hate to sead it clear to calif. this sucks :angry:
1976 KZ 900 PRO STREET 1977 kz1000 dragbike project

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: APE CAM CHAIN IDLER ADAPTER

05 Dec 2011 18:18
#491731
Jeff, I'm sure there is a machinist near you that can do it. Jay was giving you what they charge, you should be able to have it done locally for a similar price.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum