HEAD TO JUG POSSIBLE PROBLEM ???????????

  • JEFFG1
  • JEFFG1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 341
  • Thanks: 16

HEAD TO JUG POSSIBLE PROBLEM ???????????

06 Dec 2011 22:54 - 06 Dec 2011 22:55
#491960

Attachment DRAGBIKE042.jpg not found



Attachment DRAGBIKE041.jpg not found



Attachment DRAGBIKE040.jpg not found


well here i go with another problem or not. i have been cleaning up the runners ect. on the j head that i was told is a kz1100. when my fingers get sore from sanding :pinch: i clean up parts that came off the motor i am useing for the dragbike. i was cleaning the old jug which is 1015 bored to a 1075 kit and noticed the rubber o ring that seals the cam chain guide.so i got to looking at the 1260 jug i am going to use which is a 903 sleeved and the groove for the o ring isnt there :whistle: then i looked at the kz1100 head and it isnt there. i might note know alot about stuff but i know that this could be a problem :sick:
1976 KZ 900 PRO STREET 1977 kz1000 dragbike project
Last edit: 06 Dec 2011 22:55 by JEFFG1.

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: HEAD TO JUG POSSIBLE PROBLEM ???????????

06 Dec 2011 23:09
#491963
I don't remember the exact details, but I believe depending on your head gasket you made not need the o-ring? I know some guys fill the groove with high temp silicone when running copper gaskets? Again, I'm not the expert, but someone else with the answers will be here shortly.... :S

Please Log in or Create an account to join the conversation.

  • etbike3135
  • etbike3135's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 379
  • Thanks: 50

Re: HEAD TO JUG POSSIBLE PROBLEM ???????????

06 Dec 2011 23:57
#491971
Use a one piece Cometic graphite head gasket and it will work perfect. In fact the 1260 jug is bored into an early 900 block with no oring and is prefered for one piece head gaskets. If you were using a one piece gasket on your other block you would be filling the oring groove with silicone or something else cause the oring wont work. The head should not have a matching groove, just a flat surface.
You doing good, be glad you got that block. There is a reason those were prefered for bigger sleeves and pistons.
1973 Kawasaki Z1
18 years in dragbikes
The following user(s) said Thank You: DoubleDub

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: HEAD TO JUG POSSIBLE PROBLEM ???????????

07 Dec 2011 10:50
#492015
Nice Bumps!! ;)

1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: HEAD TO JUG POSSIBLE PROBLEM ???????????

07 Dec 2011 10:57
#492018
Yes, both sets are some fun looking pistons...I concur.

Please Log in or Create an account to join the conversation.

  • JEFFG1
  • JEFFG1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 341
  • Thanks: 16

Re: HEAD TO JUG POSSIBLE PROBLEM ???????????

07 Dec 2011 11:59
#492022
well i cant believe that something went rite on this :woohoo: i will get one of those gaskets and see what happens. i got a set of rs38s from les holt he gave me a very good deal i thank him for that. hopefully they will feed them hungry bumps
1976 KZ 900 PRO STREET 1977 kz1000 dragbike project

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: HEAD TO JUG POSSIBLE PROBLEM ???????????

07 Dec 2011 18:26
#492058
have a look at chamber #3.
there is a sharp edge between the valve seat and plug hole. deburr and smooth that up , and remove any others u may find. they are a prime source for a hot spot, thus, detonation.
have fun.

Attachment kz1100.jpg not found

76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • LarryC
  • LarryC's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1241
  • Thanks: 309

Re: HEAD TO JUG POSSIBLE PROBLEM ???????????

07 Dec 2011 20:09 - 07 Dec 2011 20:15
#492082
Oh yea..... ;) One and Two are nearly as bad. Looks like someone had a go at the valve job with a 30 degree stone that was a tad big at some point.

What have you got for tools to work with on the head?

Attachment sharpedge.jpg not found

Larry C.
Last edit: 07 Dec 2011 20:15 by LarryC.

Please Log in or Create an account to join the conversation.

  • LarryC
  • LarryC's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1241
  • Thanks: 309

Re: HEAD TO JUG POSSIBLE PROBLEM ???????????

07 Dec 2011 20:20
#492085
Here's the right way to go about it.
Larry C.

Please Log in or Create an account to join the conversation.

  • JEFFG1
  • JEFFG1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 341
  • Thanks: 16

Re: HEAD TO JUG POSSIBLE PROBLEM ???????????

07 Dec 2011 21:34
#492096
ya there is alittle burr on all of them i didnt do that all i used is a peice of 180 sand paper on the the tub to clean the carbon off then a piece of red scuff pad.on the runners i used a dremal and 80 grit to smooth then out sanding with the flow.i will debure those areas though.
1976 KZ 900 PRO STREET 1977 kz1000 dragbike project

Please Log in or Create an account to join the conversation.

  • LarryC
  • LarryC's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1241
  • Thanks: 309

Re: HEAD TO JUG POSSIBLE PROBLEM ???????????

07 Dec 2011 22:06
#492104
Jeff,

Was this a used head you picked up somewhere?
Larry C.

Please Log in or Create an account to join the conversation.

  • JEFFG1
  • JEFFG1's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 341
  • Thanks: 16

Re: HEAD TO JUG POSSIBLE PROBLEM ???????????

07 Dec 2011 23:38
#492121
ya it was a used one i picked up on ebay about a month ago
1976 KZ 900 PRO STREET 1977 kz1000 dragbike project

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum