77 kz650 not starting
- M. WATKINS
-
Topic Author
- Offline
- User
-

Registered
- Posts: 31
- Thanks: 0
77 kz650 not starting
08 Dec 2011 22:05
Hello all,
I have an issue with my 1977 kz650 custom, I have been getting the bike together for some time now with new seals, bearings and whatever else needed replacing along the way.
It used to start like a champ of either the kick start or starter motor. I just changed the contact breaker parts and condenser as a matter of course, after setting the points gap I tried firing the bike up, it did not start and sounded like something was seriously off with the bike backfiring back through the air box. I struggled with this for a while and resorted to refitting the old points but to nom avail.
The points sparking, as are the plugs, which are wet so fuels is definitely getting through.
I did resolder a burnt out connection for the oil warning switch, but did not interfere with the Black and green wires from the points into the loom.
I am at a loss here as there is fuel present and a good blue spark at each plug.
Can anyone shed any light on this for me please?
Thanks in advance for you time and advice.
Matt.
I have an issue with my 1977 kz650 custom, I have been getting the bike together for some time now with new seals, bearings and whatever else needed replacing along the way.
It used to start like a champ of either the kick start or starter motor. I just changed the contact breaker parts and condenser as a matter of course, after setting the points gap I tried firing the bike up, it did not start and sounded like something was seriously off with the bike backfiring back through the air box. I struggled with this for a while and resorted to refitting the old points but to nom avail.
The points sparking, as are the plugs, which are wet so fuels is definitely getting through.
I did resolder a burnt out connection for the oil warning switch, but did not interfere with the Black and green wires from the points into the loom.
I am at a loss here as there is fuel present and a good blue spark at each plug.
Can anyone shed any light on this for me please?
Thanks in advance for you time and advice.
Matt.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 77 kz650 not starting
08 Dec 2011 22:15 - 08 Dec 2011 23:41
Would static check ignition timing by assuring that the raised part of the rotor cam is just beginning to open the left-hand points as the 1/4 F mark aligns with the permanent case mark.
This will confirm that the rotor hasn't been installed 180° off.
Good Fortune!
This will confirm that the rotor hasn't been installed 180° off.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 08 Dec 2011 23:41 by Patton.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 77 kz650 not starting
08 Dec 2011 22:41
While points remain closed, the ignition coil is charging via its primary wiring being grounded through the closed points.
When the points open, the coil's primary winding ground is interrupted, which causes the coil to fire through its secondary loop including the two spark plugs.
Good Fortune!
When the points open, the coil's primary winding ground is interrupted, which causes the coil to fire through its secondary loop including the two spark plugs.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: 77 kz650 not starting
08 Dec 2011 23:16
Here is the method I use for static timing. I turn OFF the ignition. To make the task easier, I disconnect the green wire near one coil and the black wire near the other coil. (This is not in the book, but it makes checking continuity much easier for me.) After installing the new points, turn the 17 mm nut while watching the points. When points pair 1&4 are at their widest gap adjust them (by loosening the 2 screws that hold the points to the backplate) so the gap equals 0.35 mm; do this carefully as this gap will affect your ability to time the ignition. Turn the 17 mm nut clockwise through a full revolution again and double check this gap. Then repeat this for points pair 3&4. Now set your meter to test continuity and clip one lead to the leaf spring on points set 1&4 and clip the other lead to ground. Turn the 17 mm nut clockwise until the 1&4 F mark aligns with the pointer. You want the continuity across points pair 1&4 to just break when the F mark aligns with the pointer. The idea is that when the continuity just breaks is when the points will fire their respective coil and cylinders. In order to adjust the point at which continuity breaks, loosen the 3 screws that hold the backplate to the engine and slightly turn the backplate until the meter shows a break in continuity. Once you have the 1&4 points timed properly you can check the 2&3 pair to make sure they break when the 2&3 F mark aligns with the pointer. Don’t forget to plug in the green and black coil wires when you are done, and put a little grease on the rubbing block felt. Assuming you are using new points of the correct type this should enable you to get the timing very close. Trying this with old points may give poor results, especially if the points are pitted and/or the rubbing blocks are worn. Once this is done you can fine tune the adjustments using the timing light and dwell meter. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- M. WATKINS
-
Topic Author
- Offline
- User
-

Registered
- Posts: 31
- Thanks: 0
Re: 77 kz650 not starting
09 Dec 2011 19:52
Patton and Ed,
Thanks so much for your advice, the rotor was indeed 180 degrees off.....(i feel so stupid for not working this one out for myself).
Ed, I static timed the ignition and will be fine tuning it once i get a quality timing light.
Since running the bike again I can hear an inlet leak between the manifold and where the inlet rubber sits, also the head gasket shows evidence of minute bubbles....so I guess it's head off time....just as a quick reference is this an engine out job or will the head come off and clear the frame?
Thanks again guys, your life savers.
Matt.
Thanks so much for your advice, the rotor was indeed 180 degrees off.....(i feel so stupid for not working this one out for myself).
Ed, I static timed the ignition and will be fine tuning it once i get a quality timing light.
Since running the bike again I can hear an inlet leak between the manifold and where the inlet rubber sits, also the head gasket shows evidence of minute bubbles....so I guess it's head off time....just as a quick reference is this an engine out job or will the head come off and clear the frame?
Thanks again guys, your life savers.
Matt.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 77 kz650 not starting
10 Dec 2011 00:35 - 10 Dec 2011 00:45M. WATKINS wrote: ...Since running the bike again I can hear an inlet leak between the manifold and where the inlet rubber sits, also the head gasket shows evidence of minute bubbles....so I guess it's head off time....just as a quick reference is this an engine out job or will the head come off and clear the frame?....
Before removing the head, would consider performing a leak-down test, which might confirm a leaking head gasket. And also re-torque the head when the engine is stone overnight sitting cold.
And repeat the leak-down test.
Should be able to remove the head without pulling the engine.
Could confirm the carb holder leak by spraying WD40 or carb spray about the suspected leak areas while the engine is running at idle or low rpm, and watch for increased smoke from the exhaust and/or change in rpm.
Also assure that the carbs are pushed correctly and fully into the holders, and that the clamps are properly positioned and snugly tightened. It's okay to apply WD40 or silicone lube or Armoral inside the carb holders to help push the carbs into position.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 10 Dec 2011 00:45 by Patton.
Please Log in or Create an account to join the conversation.
- M. WATKINS
-
Topic Author
- Offline
- User
-

Registered
- Posts: 31
- Thanks: 0
Re: 77 kz650 not starting
13 Dec 2011 03:25
Thanks for the tips Patton,
the air intake rubber is definately leaking as there is a hiss that changes pitch when you hold your finger around it on the underside of the # 4 inlet rubber, also i can feel it sucking on my finger as i hold it over where the rubber sits on the inlet manifold.
as for the head gasket....i can actually see tiny bubbles coming from the head gasket along the outside lip where it sits on the barrells..i may also try the leak down test as you suggested however i am sure the head would benifit from a thorough inspection
at the very least the inlet manifold will have to be done, any tips on that?
Also, any tips on the head gasket and things to look for when the head is off, i have not removed a kz head before.
thanks again.
Matt.
the air intake rubber is definately leaking as there is a hiss that changes pitch when you hold your finger around it on the underside of the # 4 inlet rubber, also i can feel it sucking on my finger as i hold it over where the rubber sits on the inlet manifold.
as for the head gasket....i can actually see tiny bubbles coming from the head gasket along the outside lip where it sits on the barrells..i may also try the leak down test as you suggested however i am sure the head would benifit from a thorough inspection
at the very least the inlet manifold will have to be done, any tips on that?
Also, any tips on the head gasket and things to look for when the head is off, i have not removed a kz head before.
thanks again.
Matt.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 77 kz650 not starting
13 Dec 2011 12:21
If not already done, don't forget the head re-torque, which may not help but worth a try.
If the intake leak is through the carb holder vacuum nipple, a replacement plug/cap might stop the leak.
Am uncertain as to exactly where the leak-hiss is located, whether in the carb holder (between carb and engine) or air hose (between carb and air box).
Lasting repairs to bad carb holders are virtually impossible.
Z1 Enterprises lists the holders, hoses, and plugs.
Good Fortune!
If the intake leak is through the carb holder vacuum nipple, a replacement plug/cap might stop the leak.
Lasting repairs to bad carb holders are virtually impossible.
Z1 Enterprises lists the holders, hoses, and plugs.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- M. WATKINS
-
Topic Author
- Offline
- User
-

Registered
- Posts: 31
- Thanks: 0
Please Log in or Create an account to join the conversation.
- Beaker
-
- Offline
- User
-

Registered
- Posts: 5
- Thanks: 0
Re: 77 kz650 not starting
26 Dec 2011 07:49
what i found was the DOHC in a single configuration acts as a SOHC and not vise verse like the engineers said i only did one B line mid year modle.Not exactly sure of the science i stumbled on but off set the time and timed both compression cyclinders then exhaust cylinders on the compression stroke ,,,if you can straighten out this mess it will run smooth i stumbled on it,,,,also ounce it runs right youl get a terribble tap in the lifter you cant seem to shake,,,here gos on that ounce your running right and you now have the tapping remove top and role the engine to tdc set it to 10 thousanths then role counterclock till that lifter gets real loose then set to 10 thoughsanths and there ya go good luck sorry if i confused it more but i was baffled for months on that
Beaker
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: 77 kz650 not starting
26 Dec 2011 19:40Beaker wrote: what i found was the DOHC in a single configuration acts as a SOHC and not vise verse like the engineers said i only did one B line mid year modle.Not exactly sure of the science i stumbled on but off set the time and timed both compression cyclinders then exhaust cylinders on the compression stroke ,,,if you can straighten out this mess it will run smooth i stumbled on it,,,,also ounce it runs right youl get a terribble tap in the lifter you cant seem to shake,,,here gos on that ounce your running right and you now have the tapping remove top and role the engine to tdc set it to 10 thousanths then role counterclock till that lifter gets real loose then set to 10 thoughsanths and there ya go good luck sorry if i confused it more but i was baffled for months on that
$10 to anyone that can translate this..... :laugh:
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
