1978 kz650 reassembley
- nitrochristian
-
Topic Author
- Offline
- User
-

Registered
- Posts: 39
- Thanks: 0
1978 kz650 reassembley
09 Dec 2011 00:27
Looking for some tips, I'm putting our 650 back together and it has been over 2 years since we bought it from craigslist $200.00. My son and I wanted a father and son project and we love drag racing so we bought the bike and dug in. There are a few pics in the gallery. It has been tough but we are getting close to having the engine complete specs 710 kit and gpz750 cams, we have a few questions? 1. the top end is back together but the carbs are not going to be ready till mid Jan, we are concerned about leaving it alone and that causing problems, should we put some oil in the plug holes and turn it over a few time a week? 2. While reworking the heads we bought a thread chaser for the plug holes 14mm and one of the holes was pretty rough when we finished, i put a plug in and it tightened up good but we are thinking about a heli coil for it? 3. When we set the timing by the book everything looked great and we turned it over many times always looked rite untill we installed the cam chain adjuster now the timing marks dont look the same, we took the adjuster off and everything looked fine so we are hoping its fine?
78 KZ650
96 Ford Bronco
96 Ford Bronco
Please Log in or Create an account to join the conversation.
- elfmagic17
-
- Offline
- User
-

Registered
- Posts: 334
- Thanks: 24
Re: 1978 kz650 reassembley
09 Dec 2011 02:26
1. the top end is back together but the carbs are not going to be ready till mid Jan, we are concerned about leaving it alone and that causing problems, should we put some oil in the plug holes and turn it over a few time a week? (My Sugestion) A little oil won't hurt and I'd probably spin it over once a month or so if its in high humidity and gets Dew in it, otherwise would not really need to do much with it. Probably should plug the intakes to keep out dust and debris though.
2. While reworking the heads we bought a thread chaser for the plug holes 14mm and one of the holes was pretty rough when we finished, i put a plug in and it tightened up good but we are thinking about a heli coil for it? (My two cents) If its already together don't sweat it till it is a problem, unless it's going to always be in the back of your mind and drive you crazy. If it torques down properly you should not have any trouble with it.
3. When we set the timing by the book everything looked great and we turned it over many times always looked rite untill we installed the cam chain adjuster now the timing marks dont look the same, we took the adjuster off and everything looked fine so we are hoping its fine? (My Opinion)Timing should line up properly with the tensioner,idlers,ect. all in place, if it doesn't it's not right. A good way to check is if it spins over (by hand) and nothing binds (like valves hitting piston) check compression Good numbers means its most likely right. If not then reset it and recheck after tensioner is installed.
2. While reworking the heads we bought a thread chaser for the plug holes 14mm and one of the holes was pretty rough when we finished, i put a plug in and it tightened up good but we are thinking about a heli coil for it? (My two cents) If its already together don't sweat it till it is a problem, unless it's going to always be in the back of your mind and drive you crazy. If it torques down properly you should not have any trouble with it.
3. When we set the timing by the book everything looked great and we turned it over many times always looked rite untill we installed the cam chain adjuster now the timing marks dont look the same, we took the adjuster off and everything looked fine so we are hoping its fine? (My Opinion)Timing should line up properly with the tensioner,idlers,ect. all in place, if it doesn't it's not right. A good way to check is if it spins over (by hand) and nothing binds (like valves hitting piston) check compression Good numbers means its most likely right. If not then reset it and recheck after tensioner is installed.
Kenny Hicks
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)
Please Log in or Create an account to join the conversation.
- nitrochristian
-
Topic Author
- Offline
- User
-

Registered
- Posts: 39
- Thanks: 0
Re: 1978 kz650 reassembley
12 Dec 2011 02:04
Hey Guys I was hopeing for more replies help me out if you can.
78 KZ650
96 Ford Bronco
96 Ford Bronco
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
