79 KZ750 winter work

  • EsaPro
  • EsaPro's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 183
  • Thanks: 2

79 KZ750 winter work

17 Dec 2011 14:05
#493475
Hey gang! Been a while since I posted, but I'm baaaaack! B) The old girl has been running fairly well, but leaking oil around the cylinder head, so I decided to bring her in, replace the gasket, rebuild the carbs, and put on some better looking parts I have been accumulating (Front fender, fork covers, front rim).

I got down to pulling the cylinder head today, and this is what I see. Also, there was a funky burnt / dead animal kind of smell :( It was running good - I had it out for a ride the day before I rolled in into the house.

The question is - should I get the valves re-worked? I was not going to jack with them, hoping to just put it back together and not have to worry about new shims, etc. The valve work is beyond me (OK, most of this is beyond me!!) I would take it to a shop. Though I do have the service manual...

Jim.
Jim
79 KZ750 Twin (Fun!)
07 Yamaha 1300 (Plush!)

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: 79 KZ750 winter work

17 Dec 2011 16:28
#493486
That's a lot of white residue. Not what I've seen in other motors, but I'm not knowledgable enough to say why. Not sure about the smell, either. Usually an off smell would happen if you were burning something else - like a mouse :lol:

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: 79 KZ750 winter work

17 Dec 2011 16:37 - 17 Dec 2011 16:39
#493487
A white exhaust valve can mean running too hot (which means too lean). You need to do a compression test to see if the valves are seating well. I would definitely get the valvews lapped and seals replaced while it's off.
1979 KZ-750 Twin
Last edit: 17 Dec 2011 16:39 by bountyhunter.

Please Log in or Create an account to join the conversation.

  • LarryC
  • LarryC's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1241
  • Thanks: 309

Re: 79 KZ750 winter work

17 Dec 2011 17:54 - 17 Dec 2011 17:57
#493493
Do a liquid test in the ports and see if the valves are leaking. If any are, it needs attention.

If you have the ability to take it apart yourself, then do that and post up photos of the valve seat condition and valve faces.

750 heads sometimes prove to have chipped valve seats on the outside edges. It's not always evident unless you de-carbon the chambers. That happens just outboard of the actual 45 degree seat cut. As such, the bike continues to run fine.

Over time, if the seat is chipped, it can cause a crack that leads down into the 45 cut. That's when it will begin to act up.

That situation doesn't happen all the time but it happens often enough to where it's a good idea to investigate while it's off.
Larry C.
Last edit: 17 Dec 2011 17:57 by LarryC.

Please Log in or Create an account to join the conversation.

  • EsaPro
  • EsaPro's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 183
  • Thanks: 2

Re: 79 KZ750 winter work

17 Dec 2011 21:08
#493533
Oh, I have no doubt I can get it apart - it's getting it back together that concerns me! Seriously, I don't have a spring compressor, but I could get one. I have thought about at least taking them out, cleaning them up and lapping them. Keep in mind, these are all things I have NEVER done before, but then again, I had never rebuilt master cylinders and calipers before I got this bike, and I did those back in 2007. Having the service manual certainly gives one a sense of bravado, at least.

I suppose there is no point in trying to clean them up without taking them apart. As I typed that I know it is true. I might as well do it right since I am this far in. I have a few months of bitchin' cold weather to work on it... and another bike to ride if a warm day comes around!

Thanks guys... more to come I am sure.
Jim
79 KZ750 Twin (Fun!)
07 Yamaha 1300 (Plush!)

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: 79 KZ750 winter work

17 Dec 2011 23:37 - 17 Dec 2011 23:46
#493558
DIY valve spring compressor --










A modified PVC joint or section may also suffice.



Good Fortune! :)
1973 Z1
KZ900 LTD
Last edit: 17 Dec 2011 23:46 by Patton.

Please Log in or Create an account to join the conversation.

  • EsaPro
  • EsaPro's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 183
  • Thanks: 2

Re: 79 KZ750 winter work

18 Dec 2011 21:50
#493692
Thanks Patton - the ruler helps a lot! I have seen where this was done with a cut-out socket as well. What size pipe / socket gets the clearance needed? The manual mentions a "valve guide arbor" to drive the guides out. What is an acceptable substitute for that?

This is getting me dangerously close to actually doing this....
Jim
79 KZ750 Twin (Fun!)
07 Yamaha 1300 (Plush!)

Please Log in or Create an account to join the conversation.

  • EsaPro
  • EsaPro's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 183
  • Thanks: 2

Re: 79 KZ750 winter work

18 Dec 2011 21:52
#493693
LarryC - "de-carbon the chambers" - carb cleaner and a toothbrush?
Jim
79 KZ750 Twin (Fun!)
07 Yamaha 1300 (Plush!)

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: 79 KZ750 winter work

19 Dec 2011 00:01
#493721
EsaPro wrote: ...The manual mentions a "valve guide arbor" to drive the guides out....

Would leave the existing guides in place until determining that new guides are needed.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • EsaPro
  • EsaPro's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 183
  • Thanks: 2

Re: 79 KZ750 winter work

19 Dec 2011 16:06
#493801
Still working on the DIY compressor - I don't even have a C-clamp big enough. I do have a long wood clamp exactly like the one in your picture though, Patton. Only gripe about that is the handle is straight. I used it to push in the brake calipers on my Chrysler van. Quite tiring on the hands. How is it on the valve springs? I think I have some sched 40 PVC around here somewhere - I take it that is strong enough? Certainly would be easier to notch than a socket.

On another note - my brother, the auto mechanic, asked me if I was going to pull the jugs off, noting that now that I have removed the head, the pressure on the base gasket has been released, and it might likely leak at the base when re-assembled. I had not planned on doing that, lacking tools (again) to re-assemble. I believe I need a ring compressor for that job.

Is it advisable to replace the base gasket as well? I have a full gasket set. What am I setting myself up for if I don't? What am I setting myself up for if I pull the jugs off? I have this feeling that I am going this far, I might as well go all the way...

Thanks again for the tips. Perhaps I should start a project post for this. I have a photo album up on Facebook for it already.
Jim
79 KZ750 Twin (Fun!)
07 Yamaha 1300 (Plush!)

Please Log in or Create an account to join the conversation.

  • Flyndrive
  • Flyndrive's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 131
  • Thanks: 4

Re: 79 KZ750 winter work

19 Dec 2011 16:40
#493806
My manual just shows that you can use large hose clamps to hold the rings compressed while you slide the pistons into the cylinders. Then you just unscrew them all the way to take them off.
1980 KZ 550A1
1985 GPZ 900R

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: 79 KZ750 winter work

19 Dec 2011 17:29
#493816
I (and I believe most) just use my hands to install the pistons. Some believe the ring compressors help, others think they are more of a hassle. Having 4 cylinders makes it difficult - you can't just install one piston at a time. Another pair of hands is the best tool you can have.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum