Decreasing engine revs
- PRM068
-
Topic Author
- Offline
- User
-

Registered
- Posts: 67
- Thanks: 0
Decreasing engine revs
18 Dec 2011 02:55
G'day guys,
riding my 82 1000 today (haven't had it long) and was wondering if it's worth looking at trying to drop the revs a little, and if so, is it as simple as changing the rear sprocket ?
At 50 mph she was sitting on roughly 3900 rpm, whilst at 65 mph it was around 5000 rpm. Is that pretty standard, or what ? new to bikes so thought I'd ask.
Is changing the rear srpocket a common alteration ?
Any advice/opinions welcomed.
Thanks,
Peter
riding my 82 1000 today (haven't had it long) and was wondering if it's worth looking at trying to drop the revs a little, and if so, is it as simple as changing the rear sprocket ?
At 50 mph she was sitting on roughly 3900 rpm, whilst at 65 mph it was around 5000 rpm. Is that pretty standard, or what ? new to bikes so thought I'd ask.
Is changing the rear srpocket a common alteration ?
Any advice/opinions welcomed.
Thanks,
Peter
1982 KZ1000 LTD
Please Log in or Create an account to join the conversation.
- clutch
-
- Offline
- User
-

Registered
- I wish I had a tad more patience to do it better!
- Posts: 1051
- Thanks: 13
Re: Decreasing engine revs
18 Dec 2011 03:26
My 750 is about the same on the rpm's at those speeds. Changing the rear sprocket and/or the front sprockets can give you the desired effect (though it will decrease your acceleration as well). I forget whether you need to go bigger or smaller, so I will let someone else give you that info.
Southern Maryland, USA
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
Please Log in or Create an account to join the conversation.
- PRM068
-
Topic Author
- Offline
- User
-

Registered
- Posts: 67
- Thanks: 0
Re: Decreasing engine revs
18 Dec 2011 06:32
I'm pretty sure it's "go one less tooth" on the rear cog to get lower revs (and slower accelleration). Just curious if those revs sounded right and if many people tried to reduce them.
Peter
Peter
1982 KZ1000 LTD
Please Log in or Create an account to join the conversation.
- hugo
-
- Offline
- User
-

Registered
- '92 Zephyr 750
- Posts: 313
- Thanks: 95
Re: Decreasing engine revs
18 Dec 2011 11:52 - 18 Dec 2011 11:55
It is too high. For 1000 cc, at 3900 RPM should be doing about 60 mph, like he Suzuki GS1000 used to do, and I used to have a Yamaha FJ1100 that would 60 mph at 3600 RPM. The KZ750 used to turn about 4400 rpm for 60 mph. I have a Zephyr 750 and have it doing 3900 at 60 mph, by going up two teeth on frong sprocket. Stock was doing 4600 rpm at 60 mph.
Is easier to change fron sproket as you don't have to remove wheel. larger front sprocket is also easier on the chain, as it bends less and less frequently. Although a little accel is lost. I am not interested in racing anybody, so I don't really notice the difference.
Is easier to change fron sproket as you don't have to remove wheel. larger front sprocket is also easier on the chain, as it bends less and less frequently. Although a little accel is lost. I am not interested in racing anybody, so I don't really notice the difference.
Last edit: 18 Dec 2011 11:55 by hugo.
Please Log in or Create an account to join the conversation.
- clutch
-
- Offline
- User
-

Registered
- I wish I had a tad more patience to do it better!
- Posts: 1051
- Thanks: 13
Re: Decreasing engine revs
20 Dec 2011 16:05
Forgot to mention I swapped out the 18" wheel with a 16" wheel. Using the same sprocket though...not sure if that means I have higher or lower rpms now...this hurts my head thinking about it lol
Southern Maryland, USA
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
1980 KZ250 LTD (traded, but still missed)
1982 KZ750 E3 (Cafe Project) (Dyna-S, Dyna Coils, V&H 4-1, K&N Pods, 6 Sigma Jet Kit, Acewell Computer, Woodcraft Clip-ons, Custom Rewire)
1966 A1 Samurai (Restoration Project)
Wish List:
KZ1000 P (For a "touring" bike)
Z1 (need I say more?)
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Decreasing engine revs
20 Dec 2011 17:56
Use
www.gearingcommander.com
to calculate engine rpm's and tire sizes.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- LarryC
-
- Offline
- User
-

Registered
- Posts: 1241
- Thanks: 309
Re: Decreasing engine revs
21 Dec 2011 00:29hugo wrote: It is too high. For 1000 cc, at 3900 RPM should be doing about 60 mph, like he Suzuki GS1000 used to do, and I used to have a Yamaha FJ1100 that would 60 mph at 3600 RPM. The KZ750 used to turn about 4400 rpm for 60 mph. I have a Zephyr 750 and have it doing 3900 at 60 mph, by going up two teeth on frong sprocket. Stock was doing 4600 rpm at 60 mph.
Is easier to change fron sproket as you don't have to remove wheel. larger front sprocket is also easier on the chain, as it bends less and less frequently. Although a little accel is lost. I am not interested in racing anybody, so I don't really notice the difference.
x2 .... go up 1 tooth on the front sprocket. As long as you have enough chain adjustment room left. It will naturally shorten your chain a little.
Larry C.
Please Log in or Create an account to join the conversation.
- tapeworm
-
- Offline
- User
-

Registered
- Posts: 2
- Thanks: 0
Re: Decreasing engine revs
21 Dec 2011 03:58 - 21 Dec 2011 04:01
Hi all. New to this forum; stumbled onto it looking for soln to stolen keys. Got the issue solved thanks to rstnick. If I may weigh into this a little, as I've converted 2 bikes so far (not your class of bike, but close enough). I've changed both sprockets on both bikes. Fol are the situations/conditions. I commute 100 miles round-trip every day, mostly highway, so I'm interested in low RPMs at cruising speeds, and don't really care about lifting the front tire from at a stop sign.
First Bike - 2011 Ninja 250: Buzzed like an angry Mosquito at highway speeds with stock sprockets (F14T, R45T). First gear in this configuration was a brisk walking pace in 1st gear to 5000RPM - silly stuff. New configuration is F15T and R42T. You want to make the front sprocket bigger and the rear sprocket smaller to achieve lower RPM for a given speed. CAUTION: I initially thought I would be able to fit a R39T sprocket, but that would have required me to take links out of the chain. Overall, this mod (up 1T in the front, down 3T in the rear) provides me 1600-less RPM for any given speed, and results in going from 3.7L/100km to 3.2L/100km (64-74 MPG) So I no longer need to think about getting a scooter to save gas...and instead of running near 11000 RPM at 65mph, I now cruise at a comfortable 9000RPM, about a third into the powerband. When you change gearing, you want to consider in what range your bike is peppy, cause you probably don't want to gear it down too far so that when you twist it, not much happens. In deciding which sprocket to upsize, and which one to downsize, think of how a 10-speed bicycle works. Big in front, small in back means less pedaling (but harder to get going from a stand-still).
Second Bike - 1994 Ninja 600: Needed to replace chain and sprockets anyway. Came with F16T and R48T. Went to F17T and R46T. Dropped a cool 1000 RPM, now doing 65mph at 5K vice 6K. Plenty of squirt left, and first gear stretches its legs nicely.
To remove & torque the front sprocket, you should have someone sit on the bike and apply both brakes to ensure the crank/bike does not move. For the removal I used an air wrench without any apparent ill effect. For replacing the rear sprocket, be sure to have a ready supply of studs on hand. One of the studs stripped on my 250 in the process of re-using the old locknut (contrary to what the svc manual suggest, of course), and this resulted in a 30-day downtime as the parts had to come from Japan...intensive search for studs and locknuts turned up zero to exactly fit behind the swing arm. Amazing...you'd think these would be on hand at major Kawi service centers. Overall, highly recommend re-gearing if you are looking to drop RPMs for highway cruising, esp. if it is time to replace chain/sprockets anyway.
The jt gear ratio chart (attached) is accurate (I have no affiliation with JT).
First Bike - 2011 Ninja 250: Buzzed like an angry Mosquito at highway speeds with stock sprockets (F14T, R45T). First gear in this configuration was a brisk walking pace in 1st gear to 5000RPM - silly stuff. New configuration is F15T and R42T. You want to make the front sprocket bigger and the rear sprocket smaller to achieve lower RPM for a given speed. CAUTION: I initially thought I would be able to fit a R39T sprocket, but that would have required me to take links out of the chain. Overall, this mod (up 1T in the front, down 3T in the rear) provides me 1600-less RPM for any given speed, and results in going from 3.7L/100km to 3.2L/100km (64-74 MPG) So I no longer need to think about getting a scooter to save gas...and instead of running near 11000 RPM at 65mph, I now cruise at a comfortable 9000RPM, about a third into the powerband. When you change gearing, you want to consider in what range your bike is peppy, cause you probably don't want to gear it down too far so that when you twist it, not much happens. In deciding which sprocket to upsize, and which one to downsize, think of how a 10-speed bicycle works. Big in front, small in back means less pedaling (but harder to get going from a stand-still).
Second Bike - 1994 Ninja 600: Needed to replace chain and sprockets anyway. Came with F16T and R48T. Went to F17T and R46T. Dropped a cool 1000 RPM, now doing 65mph at 5K vice 6K. Plenty of squirt left, and first gear stretches its legs nicely.
To remove & torque the front sprocket, you should have someone sit on the bike and apply both brakes to ensure the crank/bike does not move. For the removal I used an air wrench without any apparent ill effect. For replacing the rear sprocket, be sure to have a ready supply of studs on hand. One of the studs stripped on my 250 in the process of re-using the old locknut (contrary to what the svc manual suggest, of course), and this resulted in a 30-day downtime as the parts had to come from Japan...intensive search for studs and locknuts turned up zero to exactly fit behind the swing arm. Amazing...you'd think these would be on hand at major Kawi service centers. Overall, highly recommend re-gearing if you are looking to drop RPMs for highway cruising, esp. if it is time to replace chain/sprockets anyway.
The jt gear ratio chart (attached) is accurate (I have no affiliation with JT).
Last edit: 21 Dec 2011 04:01 by tapeworm. Reason: Attaching file as jpeg vice pdf
Please Log in or Create an account to join the conversation.
- 400North
-
- Offline
- User
-

Registered
- Posts: 4
- Thanks: 0
Re: Decreasing engine revs
21 Dec 2011 07:13
The rim size isn't the issue so much as the total diameter of the tire. I am guessing here that the tire is smaller in diameter than the original in which case you can compensate for this buy either going larger on the counter sprocket. 1-2 teeth larger. Go lower on the rear sprocket (fewer teeth),or a combination of both. Generally speaking adding a tooth to the front counter sprocket is essentially the same as running a rear sprocket with 3 fewer teeth. This is only approximate.
The cheapest route here is to run a slightly bigger counter sprocket (maybe 1 tooth) and see what it does for your cruise engine speed and then go from there. There isn't always enough room to run a really large counter sprocket,depends on the engine.It's a trial and error thing.
Cheers,
Lou
The cheapest route here is to run a slightly bigger counter sprocket (maybe 1 tooth) and see what it does for your cruise engine speed and then go from there. There isn't always enough room to run a really large counter sprocket,depends on the engine.It's a trial and error thing.
Cheers,
Lou
Please Log in or Create an account to join the conversation.
- etbike3135
-
- Offline
- User
-

Registered
- Posts: 379
- Thanks: 50
Re: Decreasing engine revs
21 Dec 2011 08:00
Your rpms are right on for how Kawasaki intended these bikes to run. 50 mph seems to be the sweet spot for rpm/fuel mileage. I have taken several different 1000's on cross country rides and did play around with the gearing and found this, the lower motor revs will promote detonation and pinging under load when the motor is really hot. I mean you have to be on the bike for 3 hours straight and then you will start to notice it. The higher revs keep this from happening. Never minded the less acceleration, its really only first gear. I think if I made an adjustment it would be one or two teeth less in the rear at the most, 1 in the front = 3 rear. Some might say its my tune up but some of these bikes were showroom stock and it didnt even matter if I used 87 or 93 gas.
1973 Kawasaki Z1
18 years in dragbikes
18 years in dragbikes
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
